[ovirt-users] Hosted-engine-Issue
Budur Nagaraju
nbudoor at gmail.com
Fri Apr 22 06:29:36 EDT 2016
I have created vms in the vmware ESXi.
Thanks,
Nagaraju
On Fri, Apr 22, 2016 at 3:38 PM, Simone Tiraboschi <stirabos at redhat.com>
wrote:
> On Fri, Apr 22, 2016 at 10:27 AM, Budur Nagaraju <nbudoor at gmail.com>
> wrote:
> > HI
> >
> > I thought Its promiscuous mode issue ,after reboot of engine unable to
> reach
> > again ? is there anyways to resolve ?
>
> Are you using a nested env?
>
> > Thanks,
> > Nagaraju
> >
> >
> > On Fri, Apr 22, 2016 at 11:45 AM, Budur Nagaraju <nbudoor at gmail.com>
> wrote:
> >>
> >> I found the solution ,promiscuous mode was rejecting the packets this
> was
> >> causing the issue ,enabled and now able to ping without any issues.
> >> Thanks for the support !
> >>
> >> On Fri, Apr 22, 2016 at 8:39 AM, Budur Nagaraju <nbudoor at gmail.com>
> wrote:
> >>>
> >>> HI
> >>>
> >>> Any updates issue is blocking ?
> >>>
> >>> Thanks,
> >>> Nagaraju
> >>>
> >>>
> >>> On Thu, Apr 21, 2016 at 7:20 PM, Budur Nagaraju <nbudoor at gmail.com>
> >>> wrote:
> >>>>
> >>>> Below are the details, unable to ping the gateway from the ovirt
> engine
> >>>> ,able to ping the ovirt engine from host as both are there in the same
> >>>> network.
> >>>>
> >>>>
> >>>> [root at oe ~]# ip addr
> >>>> 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
> >>>> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
> >>>> inet 127.0.0.1/8 scope host lo
> >>>> inet6 ::1/128 scope host
> >>>> valid_lft forever preferred_lft forever
> >>>> 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> >>>> state UP qlen 1000
> >>>> link/ether 00:16:3e:33:38:e5 brd ff:ff:ff:ff:ff:ff
> >>>> inet 10.206.66.9/23 brd 10.206.67.255 scope global eth0
> >>>> inet6 fe80::216:3eff:fe33:38e5/64 scope link
> >>>> valid_lft forever preferred_lft forever
> >>>> [root at oe ~]#
> >>>> [root at oe ~]#
> >>>> [root at oe ~]#
> >>>> [root at oe ~]# ip route
> >>>> 10.206.66.0/23 dev eth0 proto kernel scope link src 10.206.66.9
> >>>> 169.254.0.0/16 dev eth0 scope link metric 1002
> >>>> default via 10.206.67.254 dev eth0
> >>>> [root at oe ~]#
> >>>> [root at oe ~]#
> >>>> [root at oe ~]#
> >>>> [root at oe ~]# brctl show
> >>>> bridge name bridge id STP enabled interfaces
> >>>> [root at oe ~]#
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> On Thu, Apr 21, 2016 at 4:51 PM, Yedidyah Bar David <didi at redhat.com>
> >>>> wrote:
> >>>>>
> >>>>> On Thu, Apr 21, 2016 at 1:39 PM, Budur Nagaraju <nbudoor at gmail.com>
> >>>>> wrote:
> >>>>> > HI
> >>>>> >
> >>>>> > Installed hosted engine and after configuring IP to ovirt engine
> >>>>> > unable to
> >>>>> > ping the gateway and found that there is no issue with the Network
> .
> >>>>>
> >>>>> You mean that from inside the engine machine, you cannot ping the
> >>>>> gateway?
> >>>>>
> >>>>> Can you ping it from the host?
> >>>>>
> >>>>> Please share output of these commands, from both the host and the
> >>>>> engine vm:
> >>>>>
> >>>>> ip addr
> >>>>> ip route
> >>>>> brctl show
> >>>>>
> >>>>> Thanks,
> >>>>>
> >>>>> >
> >>>>> > Is there any thing am missing while installing Hosted engine ?
> below
> >>>>> > is
> >>>>> > output details,
> >>>>> >
> >>>>> >
> >>>>> > --== CONFIGURATION PREVIEW ==--
> >>>>> >
> >>>>> > Engine FQDN :
> oe.bnglab.psecure.net
> >>>>> > Bridge name : ovirtmgmt
> >>>>> > SSH daemon port : 22
> >>>>> > Gateway address : 10.206.67.254
> >>>>> > Host name for web application : hosted_engine_1
> >>>>> > Host ID : 1
> >>>>> > Image alias : hosted_engine
> >>>>> > Image size GB : 25
> >>>>> > Storage connection :
> >>>>> > 10.204.207.152:/home/heoe
> >>>>> > Console type : vnc
> >>>>> > Memory size MB : 4096
> >>>>> > MAC address : 00:16:3e:2f:5c:40
> >>>>> > Boot type : cdrom
> >>>>> > Number of CPUs : 2
> >>>>> > ISO image (for cdrom boot) :
> >>>>> > /ovirt/CentOS-6.7-x86_64-minimal.iso
> >>>>> > CPU Type : model_SandyBridge
> >>>>> >
> >>>>> > Please confirm installation settings (Yes, No)[Yes]: yes
> >>>>> > [ INFO ] Stage: Transaction setup
> >>>>> > [ INFO ] Stage: Misc configuration
> >>>>> > [ INFO ] Stage: Package installation
> >>>>> > [ INFO ] Stage: Misc configuration
> >>>>> > [ INFO ] Configuring libvirt
> >>>>> > [ INFO ] Configuring VDSM
> >>>>> > [ INFO ] Starting vdsmd
> >>>>> > [ INFO ] Waiting for VDSM hardware info
> >>>>> > [ INFO ] Waiting for VDSM hardware info
> >>>>> > [ INFO ] Creating Storage Domain
> >>>>> > [ INFO ] Creating Storage Pool
> >>>>> > [ INFO ] Connecting Storage Pool
> >>>>> > [ INFO ] Verifying sanlock lockspace initialization
> >>>>> > [ INFO ] Creating VM Image
> >>>>> > [ INFO ] Disconnecting Storage Pool
> >>>>> > [ INFO ] Start monitoring domain
> >>>>> > [ INFO ] Configuring VM
> >>>>> > [ INFO ] Updating hosted-engine configuration
> >>>>> > [ INFO ] Stage: Transaction commit
> >>>>> > [ INFO ] Stage: Closing up
> >>>>> > The following network ports should be opened:
> >>>>> > tcp:5900
> >>>>> > tcp:5901
> >>>>> > udp:5900
> >>>>> > udp:5901
> >>>>> > An example of the required configuration for iptables can
> >>>>> > be found
> >>>>> > at:
> >>>>> > /etc/ovirt-hosted-engine/iptables.example
> >>>>> > In order to configure firewalld, copy the files from
> >>>>> > /etc/ovirt-hosted-engine/firewalld to
> >>>>> > /etc/firewalld/services
> >>>>> > and execute the following commands:
> >>>>> > firewall-cmd -service hosted-console
> >>>>> > [ INFO ] Creating VM
> >>>>> > You can now connect to the VM with the following command:
> >>>>> > /usr/bin/remote-viewer vnc://localhost:5900
> >>>>> > Use temporary password "2049ZfXr" to connect to vnc
> >>>>> > console.
> >>>>> > Please note that in order to use remote-viewer you need
> to
> >>>>> > be able
> >>>>> > to run graphical applications.
> >>>>> > This means that if you are using ssh you have to supply
> the
> >>>>> > -Y
> >>>>> > flag (enables trusted X11 forwarding).
> >>>>> > Otherwise you can run the command from a terminal in your
> >>>>> > preferred desktop environment.
> >>>>> > If you cannot run graphical applications you can connect
> to
> >>>>> > the
> >>>>> > graphic console from another host or connect to the console using
> the
> >>>>> > following command:
> >>>>> > virsh -c qemu+tls://Test/system console HostedEngine
> >>>>> > If you need to reboot the VM you will need to start it
> >>>>> > manually
> >>>>> > using the command:
> >>>>> > hosted-engine --vm-start
> >>>>> > You can then set a temporary password using the command:
> >>>>> > hosted-engine --add-console-password
> >>>>> > The VM has been started. Install the OS and shut down or
> >>>>> > reboot
> >>>>> > it. To continue please make a selection:
> >>>>> >
> >>>>> > (1) Continue setup - VM installation is complete
> >>>>> > (2) Reboot the VM and restart installation
> >>>>> > (3) Abort setup
> >>>>> > (4) Destroy VM and abort setup
> >>>>> >
> >>>>> > _______________________________________________
> >>>>> > Users mailing list
> >>>>> > Users at ovirt.org
> >>>>> > http://lists.ovirt.org/mailman/listinfo/users
> >>>>> >
> >>>>>
> >>>>>
> >>>>>
> >>>>> --
> >>>>> Didi
> >>>>
> >>>>
> >>>
> >>
> >
> >
> > _______________________________________________
> > Users mailing list
> > Users at ovirt.org
> > http://lists.ovirt.org/mailman/listinfo/users
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20160422/c22c8a95/attachment-0001.html>
More information about the Users
mailing list