[ovirt-users] oVirt Windows Guest Tools & Live Migration issues.

[Anantha Raghava]

Hello Michal,

Guest tools are working and getting all details about guest vm as needed.

But one thing I didn't understand. What is the relationship between 
virtioserial driver and oVirt Guest Service? Without virtio serial 
driver, guest services does not start.

Also, how do we install memory baloon driver?

Tomorrow morning, I will post about Live Migration events after I 
attempt it.

-- 

Thanks & Regards,


Anantha Raghava


On Friday 03 June 2016 04:36 PM, Michal Skrivanek wrote:
>
>> On 03 Jun 2016, at 12:57, Anantha Raghava 
>> <raghav at exzatechconsulting.com 
>> <mailto:raghav at exzatechconsulting.com>> wrote:
>>
>> Hello Michal,
>>
>> Thanks for quick feed back.
>>
>> Windows Guests Agents - Where do I download them from? Not getting 
>> the proper links. Or is to a part of virt-drivers that we use during 
>> installation.
>
> Hi Anantha,
> it’s part of ovirt-guest-tools. See 
> http://lists.ovirt.org/pipermail/users/2016-May/039779.html
>
>>
>> Live migration failure - These are pretty busy VMs if not big. The 
>> event does not show any specific message but just as migration 
>> failed. Is the reason logged somewhere? Please share the log location 
>> so that I can check & share the log for meaningful message and proper 
>> screen shots.
>
> There should be more details in the events at the bottom of the 
> webadmin page (just make it a bit bigger it may not be te last message)
> If they are busy VMs then you may have issues migrating them. There is 
> some simple tuning available and it may help. You can increase the 
> maximum downtime in VM properties dialog (500ms by default, you can go 
> up to whatever is feasible for your VM, seconds, tens of seconds)
> Bandwidth is limited to work on 1Gb network, if you have 10Gb availabl 
> you can also tune /etc/vdsm.conf on each host and increase the maximum 
> bandwidth 10 times
>
> Thanks,
> michal
>
>>
>> -- 
>>
>> Thanks & Regards,
>>
>>
>> Anantha Raghava
>>
>>
>>>> On 03 Jun 2016, at 07:14, Anantha Raghava 
>>>> <raghav at exzatechconsulting.com> wrote:
>>>>
>>>> Hi,
>>>>
>>>> We have just installed oVirt 3.6 on 3 hosts with storage volumes on 
>>>> Fibre Channel storage box. Every thing is working fine except the 
>>>> following.
>>>>
>>>> 1. We have created 15 Virtual Machines all VM with Windows Server 
>>>> 2012 R2 OS. VM properties does not report the Operating System nor 
>>>> it shows the IP and FQDN in the Admin Portal. There is always an 
>>>> exclamation mark that reports about OS being different from the 
>>>> template and timezone issues. We have changed the timezone to 
>>>> Indian Standard Time in both VM and Host, same result continues. We 
>>>> have installed Windows Gues Tools, same result continues. Screen 
>>>> shot is below.
>>>
>>> you doesn’t seem to run the guest agent. Make sure the service is 
>>> started and works, then you’ll see IPs and more detailed info about 
>>> each guest, and exclamation marks should go away
>>>
>>>>
>>>> <VMs.PNG>
>>>>
>>>> 2. When we manually tried to migrate the VMs from one host to 
>>>> another one, the migration gets initiated, but will eventually fail.
>>>>
>>>> Any specific setting missing here or is it a bug.
>>>
>>> are they big or busy VMs? What does it fail on? There should be a 
>>> menaingful message even if it’s just a timeout
>>>
>>>>
>>>> Note:
>>>>
>>>> All hosts are installed with CentOS 7.2 minimal installation oVirt 
>>>> node is installed and activated.
>>>> We do not have a DNS in our environment. We have to do with IPs.
>>>
>>> as long as engine works with FQDN it’s ok
>>>
>>>> We are yet to apply the 3.6.6 patch on Engine and Nodes.
>>>
>>> that may help with some of the issues above, so please try to do that
>>>
>>> Thanks,
>>> michal
>>>
>>>> We are running a stand alone engine, not a Hosted Engine.
>>>> --
>>>>
>>>> Thanks & Regards,
>>>>
>>>>
>>>> Anantha Raghava
>>>>
>>>> eXza Technology Consulting & Services
>>>>
>>>>
>>>> _______________________________________________
>>>> Users mailing list
>>>> Users at ovirt.org <mailto:Users at ovirt.org>
>>>> http://lists.ovirt.org/mailman/listinfo/users
>>>
>>
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.ovirt.org/pipermail/users/attachments/20160607/d60f48ee/attachment.html>