9:23 a.m.
Hi all,
I have a setup as detailed below
- iSCSI Storage Domain
- Template with Thin QCOW2 disk
- Multiple VMs from Template with Thin disk
oVirt Node 4.4.4
When the VMs boots up it downloads some data to it and that leads to
increase in volume size.
I see that every few seconds the VM gets paused with
"VM X has been paused due to no Storage space error."
and then after few seconds
"VM X has recovered from paused back to up"
Sometimes after a many pause and recovery the VM dies with
"VM X is down with error. Exit message: Lost connection with qemu process."
and I have to restart the VMs.
My questions.
1. How to work around this dying VM?
2. Is there a way to use sparse disks without VM being paused again and
again?
Thanks in advance.
Shantur
4:25 p.m.
On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore
<shantur.rathore(a)gmail.com> wrote:
Hi all,
I have a setup as detailed below
- iSCSI Storage Domain
- Template with Thin QCOW2 disk
- Multiple VMs from Template with Thin disk
Note that a single template disk used by many vms can become a performance
bottleneck, and is a single point of failure. Cloning the template when creating
vms avoids such issues.
oVirt Node 4.4.4
4.4.4 is old, you should upgrade to 4.4.7.
When the VMs boots up it downloads some data to it and that leads to
increase in volume size.
I see that every few seconds the VM gets paused with
"VM X has been paused due to no Storage space error."
and then after few seconds
"VM X has recovered from paused back to up"
This is normal operation when a vm writes too quickly and oVirt cannot
extend the disk quick enough. To mitigate this, you can increase the
volume chunk size.
Created this configuration drop in file:
# cat /etc/vdsm/vdsm.conf.d/99-local.conf
[irs]
volume_utilization_percent = 25
volume_utilization_chunk_mb = 2048
And restart vdsm.
With this setting, when free space in a disk is 1.5g, the disk will
be extended by 2g. With the default setting, when free space is
0.5g the disk was extended by 1g.
If this does not eliminate the pauses, try a larger chunk size
like 4096.
Sometimes after a many pause and recovery the VM dies with
"VM X is down with error. Exit message: Lost connection with qemu process."
This means qemu has crashed. You can find more info in the vm log at:
/var/log/libvirt/qemu/vm-name.log
We know about bugs in qemu that cause such crashes when vm disk is
extended. I think the latest bug was fixed in 4.4.6, so upgrading to 4.4.7
will fix this issue.
Even with these settings, if you have a very bursty io in the vm, it may
become paused. The only way to completely avoid these pauses is to
use a preallocated disk, or use file storage (e.g. NFS). Preallocated disk
can be thin provisioned on the server side so it does not mean you need
more storage, but you will not be able to use shared templates in the way
you use them now. You can create vm from template, but the template
is cloned to the new vm.
Another option with (still tech preview) is Managed Block Storage (Cinder
based storage). If your storage server is supported by Cinder, we can
managed it using cinderlib. In this setup every disk is a LUN, which may
be thin provisioned on the storage server. This can also offload storage
operations to the server, like cloning disks, which may be much faster and
more efficient.
Nir
5:43 p.m.
Thanks for the detailed response Nir.
In my use case, we keep creating VMs from templates and deleting them so
we need the VMs to be created quickly and cloning it will use a lot of time
and storage.
I will try to add the config and try again tomorrow. Also I like the
Managed Block storage idea, I had read about it in the past and used it
with Ceph.
Just to understand it better, is this issue only on iSCSI based storage?
Thanks again.
Regards
Shantur
On Tue, Aug 10, 2021 at 9:26 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore
<shantur.rathore(a)gmail.com> wrote:
>
> Hi all,
>
> I have a setup as detailed below
>
> - iSCSI Storage Domain
> - Template with Thin QCOW2 disk
> - Multiple VMs from Template with Thin disk
Note that a single template disk used by many vms can become a performance
bottleneck, and is a single point of failure. Cloning the template when
creating
vms avoids such issues.
> oVirt Node 4.4.4
4.4.4 is old, you should upgrade to 4.4.7.
> When the VMs boots up it downloads some data to it and that leads to
increase in volume size.
> I see that every few seconds the VM gets paused with
>
> "VM X has been paused due to no Storage space error."
>
> and then after few seconds
>
> "VM X has recovered from paused back to up"
This is normal operation when a vm writes too quickly and oVirt cannot
extend the disk quick enough. To mitigate this, you can increase the
volume chunk size.
Created this configuration drop in file:
# cat /etc/vdsm/vdsm.conf.d/99-local.conf
[irs]
volume_utilization_percent = 25
volume_utilization_chunk_mb = 2048
And restart vdsm.
With this setting, when free space in a disk is 1.5g, the disk will
be extended by 2g. With the default setting, when free space is
0.5g the disk was extended by 1g.
If this does not eliminate the pauses, try a larger chunk size
like 4096.
> Sometimes after a many pause and recovery the VM dies with
>
> "VM X is down with error. Exit message: Lost connection with qemu
process."
This means qemu has crashed. You can find more info in the vm log at:
/var/log/libvirt/qemu/vm-name.log
We know about bugs in qemu that cause such crashes when vm disk is
extended. I think the latest bug was fixed in 4.4.6, so upgrading to 4.4.7
will fix this issue.
Even with these settings, if you have a very bursty io in the vm, it may
become paused. The only way to completely avoid these pauses is to
use a preallocated disk, or use file storage (e.g. NFS). Preallocated disk
can be thin provisioned on the server side so it does not mean you need
more storage, but you will not be able to use shared templates in the way
you use them now. You can create vm from template, but the template
is cloned to the new vm.
Another option with (still tech preview) is Managed Block Storage (Cinder
based storage). If your storage server is supported by Cinder, we can
managed it using cinderlib. In this setup every disk is a LUN, which may
be thin provisioned on the storage server. This can also offload storage
operations to the server, like cloning disks, which may be much faster and
more efficient.
Nir
7:25 a.m.
On Wed, Aug 11, 2021 at 12:43 AM Shantur Rathore
<shantur.rathore(a)gmail.com> wrote:
Thanks for the detailed response Nir.
In my use case, we keep creating VMs from templates and deleting them so we need the VMs
to be created quickly and cloning it will use a lot of time and storage.
That's a good reason to use a template.
If your vm is temporary and you like to drop the data written while
the vm is running, you
could use a temporary disk based on the template. This is called a
"transient disk" in vdsm.
Arik, maybe you remember how transient disks are used in engine?
Do we have an API to run a VM once, dropping the changes to the disk
done while the VM was running?
I will try to add the config and try again tomorrow. Also I like the
Managed Block storage idea, I had read about it in the past and used it with Ceph.
Just to understand it better, is this issue only on iSCSI based storage?
Yes, on file based storage a snapshot is a file, and it grows as
needed. On block based
storage, a snapshot is a logical volume, and oVirt needs to extend it
when needed.
Nir
Thanks again.
Regards
Shantur
On Tue, Aug 10, 2021 at 9:26 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
>
> On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore
> <shantur.rathore(a)gmail.com> wrote:
> >
> > Hi all,
> >
> > I have a setup as detailed below
> >
> > - iSCSI Storage Domain
> > - Template with Thin QCOW2 disk
> > - Multiple VMs from Template with Thin disk
>
> Note that a single template disk used by many vms can become a performance
> bottleneck, and is a single point of failure. Cloning the template when creating
> vms avoids such issues.
>
> > oVirt Node 4.4.4
>
> 4.4.4 is old, you should upgrade to 4.4.7.
>
> > When the VMs boots up it downloads some data to it and that leads to increase in
volume size.
> > I see that every few seconds the VM gets paused with
> >
> > "VM X has been paused due to no Storage space error."
> >
> > and then after few seconds
> >
> > "VM X has recovered from paused back to up"
>
> This is normal operation when a vm writes too quickly and oVirt cannot
> extend the disk quick enough. To mitigate this, you can increase the
> volume chunk size.
>
> Created this configuration drop in file:
>
> # cat /etc/vdsm/vdsm.conf.d/99-local.conf
> [irs]
> volume_utilization_percent = 25
> volume_utilization_chunk_mb = 2048
>
> And restart vdsm.
>
> With this setting, when free space in a disk is 1.5g, the disk will
> be extended by 2g. With the default setting, when free space is
> 0.5g the disk was extended by 1g.
>
> If this does not eliminate the pauses, try a larger chunk size
> like 4096.
>
> > Sometimes after a many pause and recovery the VM dies with
> >
> > "VM X is down with error. Exit message: Lost connection with qemu
process."
>
> This means qemu has crashed. You can find more info in the vm log at:
> /var/log/libvirt/qemu/vm-name.log
>
> We know about bugs in qemu that cause such crashes when vm disk is
> extended. I think the latest bug was fixed in 4.4.6, so upgrading to 4.4.7
> will fix this issue.
>
> Even with these settings, if you have a very bursty io in the vm, it may
> become paused. The only way to completely avoid these pauses is to
> use a preallocated disk, or use file storage (e.g. NFS). Preallocated disk
> can be thin provisioned on the server side so it does not mean you need
> more storage, but you will not be able to use shared templates in the way
> you use them now. You can create vm from template, but the template
> is cloned to the new vm.
>
> Another option with (still tech preview) is Managed Block Storage (Cinder
> based storage). If your storage server is supported by Cinder, we can
> managed it using cinderlib. In this setup every disk is a LUN, which may
> be thin provisioned on the storage server. This can also offload storage
> operations to the server, like cloning disks, which may be much faster and
> more efficient.
>
> Nir
>
7:56 a.m.
If your vm is temporary and you like to drop the data written while
the vm is running, you
could use a temporary disk based on the template. This is called a
"transient disk" in vdsm.
Arik, maybe you remember how transient disks are used in engine?
Do we have an API to run a VM once, dropping the changes to the disk
done while the VM was running?
I think that's how stateless VMs work
9:24 a.m.
On Wed, Aug 11, 2021 at 2:56 PM Benny Zlotnik <bzlotnik(a)redhat.com> wrote:
> If your vm is temporary and you like to drop the data written
while
> the vm is running, you
> could use a temporary disk based on the template. This is called a
> "transient disk" in vdsm.
>
> Arik, maybe you remember how transient disks are used in engine?
> Do we have an API to run a VM once, dropping the changes to the disk
> done while the VM was running?
I think that's how stateless VMs work
+1
It doesn't work exactly like Nir wrote above - stateless VMs that are
thin-provisioned would have a qcow volume on top of each template's volume
and when they starts, their active volume would be a qcow volume on top of
the aforementioned qcow volume and that active volume will be removed when
the VM goes down
But yeah, stateless VMs are intended for such use case
9:41 a.m.
On Wed, Aug 11, 2021 at 4:24 PM Arik Hadas <ahadas(a)redhat.com> wrote:
On Wed, Aug 11, 2021 at 2:56 PM Benny Zlotnik <bzlotnik(a)redhat.com> wrote:
>
> > If your vm is temporary and you like to drop the data written while
> > the vm is running, you
> > could use a temporary disk based on the template. This is called a
> > "transient disk" in vdsm.
> >
> > Arik, maybe you remember how transient disks are used in engine?
> > Do we have an API to run a VM once, dropping the changes to the disk
> > done while the VM was running?
>
> I think that's how stateless VMs work
+1
It doesn't work exactly like Nir wrote above - stateless VMs that are
thin-provisioned would have a qcow volume on top of each template's volume and when
they starts, their active volume would be a qcow volume on top of the aforementioned qcow
volume and that active volume will be removed when the VM goes down
But yeah, stateless VMs are intended for such use case
I was referring to transient disks - created in vdsm:
https://github.com/oVirt/vdsm/blob/45903d01e142047093bf844628b5d90df12b6f...
This creates a *local* temporary file using qcow2 format, using the
disk on shared
storage as a backing file.
Maybe this is not used by engine?
11:39 a.m.
Hi Nir,
Just to report.
As suggested, I created a Posix compliant storage domain with CephFS
and copied my templates to CephFS.
Now I created VMs from CephFS templates and the storage error happens again.
As I understand, the storage growth issue is only on iSCSI.
Am I doing something wrong?
Kind regards,
Shantur
On Wed, Aug 11, 2021 at 2:42 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
>
> On Wed, Aug 11, 2021 at 4:24 PM Arik Hadas <ahadas(a)redhat.com> wrote:
> >
> >
> >
> > On Wed, Aug 11, 2021 at 2:56 PM Benny Zlotnik <bzlotnik(a)redhat.com>
wrote:
> >>
> >> > If your vm is temporary and you like to drop the data written while
> >> > the vm is running, you
> >> > could use a temporary disk based on the template. This is called a
> >> > "transient disk" in vdsm.
> >> >
> >> > Arik, maybe you remember how transient disks are used in engine?
> >> > Do we have an API to run a VM once, dropping the changes to the disk
> >> > done while the VM was running?
> >>
> >> I think that's how stateless VMs work
> >
> >
> > +1
> > It doesn't work exactly like Nir wrote above - stateless VMs that are
thin-provisioned would have a qcow volume on top of each template's volume and when
they starts, their active volume would be a qcow volume on top of the aforementioned qcow
volume and that active volume will be removed when the VM goes down
> > But yeah, stateless VMs are intended for such use case
>
> I was referring to transient disks - created in vdsm:
>
https://github.com/oVirt/vdsm/blob/45903d01e142047093bf844628b5d90df12b6f...
>
> This creates a *local* temporary file using qcow2 format, using the
> disk on shared
> storage as a backing file.
>
> Maybe this is not used by engine?
>
12:09 p.m.
I have actually tried many types of storage now and all have this issue.
I am not of ideas what to do
On Wed, Sep 22, 2021 at 4:39 PM Shantur Rathore
<shantur.rathore(a)gmail.com> wrote:
>
> Hi Nir,
>
> Just to report.
> As suggested, I created a Posix compliant storage domain with CephFS
> and copied my templates to CephFS.
> Now I created VMs from CephFS templates and the storage error happens again.
> As I understand, the storage growth issue is only on iSCSI.
>
> Am I doing something wrong?
>
> Kind regards,
> Shantur
>
> On Wed, Aug 11, 2021 at 2:42 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
> >
> > On Wed, Aug 11, 2021 at 4:24 PM Arik Hadas <ahadas(a)redhat.com> wrote:
> > >
> > >
> > >
> > > On Wed, Aug 11, 2021 at 2:56 PM Benny Zlotnik <bzlotnik(a)redhat.com>
wrote:
> > >>
> > >> > If your vm is temporary and you like to drop the data written
while
> > >> > the vm is running, you
> > >> > could use a temporary disk based on the template. This is called
a
> > >> > "transient disk" in vdsm.
> > >> >
> > >> > Arik, maybe you remember how transient disks are used in engine?
> > >> > Do we have an API to run a VM once, dropping the changes to the
disk
> > >> > done while the VM was running?
> > >>
> > >> I think that's how stateless VMs work
> > >
> > >
> > > +1
> > > It doesn't work exactly like Nir wrote above - stateless VMs that are
thin-provisioned would have a qcow volume on top of each template's volume and when
they starts, their active volume would be a qcow volume on top of the aforementioned qcow
volume and that active volume will be removed when the VM goes down
> > > But yeah, stateless VMs are intended for such use case
> >
> > I was referring to transient disks - created in vdsm:
> >
https://github.com/oVirt/vdsm/blob/45903d01e142047093bf844628b5d90df12b6f...
> >
> > This creates a *local* temporary file using qcow2 format, using the
> > disk on shared
> > storage as a backing file.
> >
> > Maybe this is not used by engine?
> >
1:46 a.m.
On Wednesday, 22 September 2021 18:09:28 CEST Shantur Rathore wrote:
I have actually tried many types of storage now and all have this
issue.
This is weird. Could you please use file-based storage (e.g. NFS) and post here
whole exceptions from vdsm log (/var/log/vdsm/vdsm.log) and qemu log (/var/
log/libvirt/qemu/vm_name.log) from the host which runs the VM? Hopefully this
will give us some hint what is the real issue there.
Thanks
Vojta
I am not of ideas what to do
On Wed, Sep 22, 2021 at 4:39 PM Shantur Rathore
<shantur.rathore(a)gmail.com> wrote:
>
>
> Hi Nir,
>
>
>
> Just to report.
> As suggested, I created a Posix compliant storage domain with CephFS
> and copied my templates to CephFS.
> Now I created VMs from CephFS templates and the storage error happens
> again.
As I understand, the storage growth issue is only on iSCSI.
>
>
>
> Am I doing something wrong?
>
>
>
> Kind regards,
> Shantur
>
>
>
> On Wed, Aug 11, 2021 at 2:42 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
>
> >
> >
> > On Wed, Aug 11, 2021 at 4:24 PM Arik Hadas <ahadas(a)redhat.com> wrote:
> >
> > >
> > >
> > >
> > >
> > > On Wed, Aug 11, 2021 at 2:56 PM Benny Zlotnik <bzlotnik(a)redhat.com>
> > > wrote:
> > >
> > >>
> > >>
> > >> > If your vm is temporary and you like to drop the data written
> > >> > while
> > >> > the vm is running, you
> > >> > could use a temporary disk based on the template. This is called
a
> > >> > "transient disk" in vdsm.
> > >> >
> > >> >
> > >> >
> > >> > Arik, maybe you remember how transient disks are used in engine?
> > >> > Do we have an API to run a VM once, dropping the changes to the
> > >> > disk
> > >> > done while the VM was running?
> > >>
> > >>
> > >>
> > >> I think that's how stateless VMs work
> > >
> > >
> > >
> > >
> > > +1
> > > It doesn't work exactly like Nir wrote above - stateless VMs that are
> > > thin-provisioned would have a qcow volume on top of each template's
> > > volume and when they starts, their active volume would be a qcow
> > > volume on top of the aforementioned qcow volume and that active
> > > volume will be removed when the VM goes down
But yeah, stateless
VMs
> > > are intended for such use case
> >
> >
> >
> > I was referring to transient disks - created in vdsm:
> > https://github.com/oVirt/vdsm/blob/45903d01e142047093bf844628b5d90df12b6
> > ffb/lib/vdsm/virt/vm.py#L3789
>
> >
> >
> > This creates a *local* temporary file using qcow2 format, using the
> > disk on shared
> > storage as a backing file.
> >
> >
> >
> > Maybe this is not used by engine?
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org
Privacy Statement: https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/ List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/3UEXYH2IGNDWW
YEHEHKLAREJS74LMXUI/
8:13 a.m.
Yes, on file based storage a snapshot is a file, and it grows as
needed. On block based
storage, a snapshot is a logical volume, and oVirt needs to extend it
when needed.
Forgive my ignorance, coming from vSphere background where a filesystem was
created on iSCSI LUN.
I take that this isn't the case in case of a iSCSI Storage Domain in oVirt.
On Wed, Aug 11, 2021 at 12:26 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
> On Wed, Aug 11, 2021 at 12:43 AM Shantur Rathore
> <shantur.rathore(a)gmail.com> wrote:
> >
> > Thanks for the detailed response Nir.
> >
> > In my use case, we keep creating VMs from templates and deleting them so
> we need the VMs to be created quickly and cloning it will use a lot of time
> and storage.
>
> That's a good reason to use a template.
>
> If your vm is temporary and you like to drop the data written while
> the vm is running, you
> could use a temporary disk based on the template. This is called a
> "transient disk" in vdsm.
>
> Arik, maybe you remember how transient disks are used in engine?
> Do we have an API to run a VM once, dropping the changes to the disk
> done while the VM was running?
>
> > I will try to add the config and try again tomorrow. Also I like the
> Managed Block storage idea, I had read about it in the past and used it
> with Ceph.
> >
> > Just to understand it better, is this issue only on iSCSI based storage?
>
Yes, on file based storage a snapshot is a file, and it grows as
needed. On block based
storage, a snapshot is a logical volume, and oVirt needs to extend it
when needed.
>
> Nir
>
> > Thanks again.
> >
> > Regards
> > Shantur
> >
> > On Tue, Aug 10, 2021 at 9:26 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
> >>
> >> On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore
> >> <shantur.rathore(a)gmail.com> wrote:
> >> >
> >> > Hi all,
> >> >
> >> > I have a setup as detailed below
> >> >
> >> > - iSCSI Storage Domain
> >> > - Template with Thin QCOW2 disk
> >> > - Multiple VMs from Template with Thin disk
> >>
> >> Note that a single template disk used by many vms can become a
> performance
> >> bottleneck, and is a single point of failure. Cloning the template when
> creating
> >> vms avoids such issues.
> >>
> >> > oVirt Node 4.4.4
> >>
> >> 4.4.4 is old, you should upgrade to 4.4.7.
> >>
> >> > When the VMs boots up it downloads some data to it and that leads to
> increase in volume size.
> >> > I see that every few seconds the VM gets paused with
> >> >
> >> > "VM X has been paused due to no Storage space error."
> >> >
> >> > and then after few seconds
> >> >
> >> > "VM X has recovered from paused back to up"
> >>
> >> This is normal operation when a vm writes too quickly and oVirt cannot
> >> extend the disk quick enough. To mitigate this, you can increase the
> >> volume chunk size.
> >>
> >> Created this configuration drop in file:
> >>
> >> # cat /etc/vdsm/vdsm.conf.d/99-local.conf
> >> [irs]
> >> volume_utilization_percent = 25
> >> volume_utilization_chunk_mb = 2048
> >>
> >> And restart vdsm.
> >>
> >> With this setting, when free space in a disk is 1.5g, the disk will
> >> be extended by 2g. With the default setting, when free space is
> >> 0.5g the disk was extended by 1g.
> >>
> >> If this does not eliminate the pauses, try a larger chunk size
> >> like 4096.
> >>
> >> > Sometimes after a many pause and recovery the VM dies with
> >> >
> >> > "VM X is down with error. Exit message: Lost connection with qemu
> process."
> >>
> >> This means qemu has crashed. You can find more info in the vm log at:
> >> /var/log/libvirt/qemu/vm-name.log
> >>
> >> We know about bugs in qemu that cause such crashes when vm disk is
> >> extended. I think the latest bug was fixed in 4.4.6, so upgrading to
> 4.4.7
> >> will fix this issue.
> >>
> >> Even with these settings, if you have a very bursty io in the vm, it may
> >> become paused. The only way to completely avoid these pauses is to
> >> use a preallocated disk, or use file storage (e.g. NFS). Preallocated
> disk
> >> can be thin provisioned on the server side so it does not mean you need
> >> more storage, but you will not be able to use shared templates in the
> way
> >> you use them now. You can create vm from template, but the template
> >> is cloned to the new vm.
> >>
> >> Another option with (still tech preview) is Managed Block Storage
> (Cinder
> >> based storage). If your storage server is supported by Cinder, we can
> >> managed it using cinderlib. In this setup every disk is a LUN, which may
> >> be thin provisioned on the storage server. This can also offload storage
> >> operations to the server, like cloning disks, which may be much faster
> and
> >> more efficient.
> >>
> >> Nir
> >>
>
>
9:25 a.m.
On Wed, Aug 11, 2021 at 3:13 PM Shantur Rathore
<shantur.rathore(a)gmail.com> wrote:
> Yes, on file based storage a snapshot is a file, and it grows as
> needed. On block based
> storage, a snapshot is a logical volume, and oVirt needs to extend it
> when needed.
Forgive my ignorance, coming from vSphere background where a filesystem was created on
iSCSI LUN.
I take that this isn't the case in case of a iSCSI Storage Domain in oVirt.
Yes, for block storage, we create a LVM volume group with one or more LUNs
to create a storage domain. Disks are created using LVM logical volume on
this VG.
When you create a vm from template on block storage we create a new 1g
logical volume for the vm disk, and create a qcow2 image on this logical volume
with the backing file using the template logical volume.
The logical volume needs to be extended when free space is low. This is done
automatically on the host running the VM, but since oVirt is not in the data
path, the VM may write data too fast and pause trying to write after the end
of the logical volume. In this case the VM will be resumed when oVirt finish
to extend the volume.
On Wed, Aug 11, 2021 at 12:26 PM Nir Soffer
<nsoffer(a)redhat.com> wrote:
>
> On Wed, Aug 11, 2021 at 12:43 AM Shantur Rathore
> <shantur.rathore(a)gmail.com> wrote:
> >
> > Thanks for the detailed response Nir.
> >
> > In my use case, we keep creating VMs from templates and deleting them so we need
the VMs to be created quickly and cloning it will use a lot of time and storage.
>
> That's a good reason to use a template.
>
> If your vm is temporary and you like to drop the data written while
> the vm is running, you
> could use a temporary disk based on the template. This is called a
> "transient disk" in vdsm.
>
> Arik, maybe you remember how transient disks are used in engine?
> Do we have an API to run a VM once, dropping the changes to the disk
> done while the VM was running?
>
> > I will try to add the config and try again tomorrow. Also I like the Managed
Block storage idea, I had read about it in the past and used it with Ceph.
> >
> > Just to understand it better, is this issue only on iSCSI based storage?
>
> Yes, on file based storage a snapshot is a file, and it grows as
> needed. On block based
> storage, a snapshot is a logical volume, and oVirt needs to extend it
> when needed.
>
> Nir
>
> > Thanks again.
> >
> > Regards
> > Shantur
> >
> > On Tue, Aug 10, 2021 at 9:26 PM Nir Soffer <nsoffer(a)redhat.com> wrote:
> >>
> >> On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore
> >> <shantur.rathore(a)gmail.com> wrote:
> >> >
> >> > Hi all,
> >> >
> >> > I have a setup as detailed below
> >> >
> >> > - iSCSI Storage Domain
> >> > - Template with Thin QCOW2 disk
> >> > - Multiple VMs from Template with Thin disk
> >>
> >> Note that a single template disk used by many vms can become a performance
> >> bottleneck, and is a single point of failure. Cloning the template when
creating
> >> vms avoids such issues.
> >>
> >> > oVirt Node 4.4.4
> >>
> >> 4.4.4 is old, you should upgrade to 4.4.7.
> >>
> >> > When the VMs boots up it downloads some data to it and that leads to
increase in volume size.
> >> > I see that every few seconds the VM gets paused with
> >> >
> >> > "VM X has been paused due to no Storage space error."
> >> >
> >> > and then after few seconds
> >> >
> >> > "VM X has recovered from paused back to up"
> >>
> >> This is normal operation when a vm writes too quickly and oVirt cannot
> >> extend the disk quick enough. To mitigate this, you can increase the
> >> volume chunk size.
> >>
> >> Created this configuration drop in file:
> >>
> >> # cat /etc/vdsm/vdsm.conf.d/99-local.conf
> >> [irs]
> >> volume_utilization_percent = 25
> >> volume_utilization_chunk_mb = 2048
> >>
> >> And restart vdsm.
> >>
> >> With this setting, when free space in a disk is 1.5g, the disk will
> >> be extended by 2g. With the default setting, when free space is
> >> 0.5g the disk was extended by 1g.
> >>
> >> If this does not eliminate the pauses, try a larger chunk size
> >> like 4096.
> >>
> >> > Sometimes after a many pause and recovery the VM dies with
> >> >
> >> > "VM X is down with error. Exit message: Lost connection with qemu
process."
> >>
> >> This means qemu has crashed. You can find more info in the vm log at:
> >> /var/log/libvirt/qemu/vm-name.log
> >>
> >> We know about bugs in qemu that cause such crashes when vm disk is
> >> extended. I think the latest bug was fixed in 4.4.6, so upgrading to 4.4.7
> >> will fix this issue.
> >>
> >> Even with these settings, if you have a very bursty io in the vm, it may
> >> become paused. The only way to completely avoid these pauses is to
> >> use a preallocated disk, or use file storage (e.g. NFS). Preallocated disk
> >> can be thin provisioned on the server side so it does not mean you need
> >> more storage, but you will not be able to use shared templates in the way
> >> you use them now. You can create vm from template, but the template
> >> is cloned to the new vm.
> >>
> >> Another option with (still tech preview) is Managed Block Storage (Cinder
> >> based storage). If your storage server is supported by Cinder, we can
> >> managed it using cinderlib. In this setup every disk is a LUN, which may
> >> be thin provisioned on the storage server. This can also offload storage
> >> operations to the server, like cloning disks, which may be much faster and
> >> more efficient.
> >>
> >> Nir
> >>
>
2:19 a.m.
Another option with (still tech preview) is Managed Block Storage (Cinder based storage).
It still tech preview in 4.4 ??
-----Original Message-----
From: users-bounces(a)ovirt.org <users-bounces(a)ovirt.org> On Behalf Of Nir Soffer
Sent: Wednesday, August 11, 2021 4:26 AM
To: Shantur Rathore <shantur.rathore(a)gmail.com>
Cc: users <users(a)ovirt.org>; Roman Bednar <rbednar(a)redhat.com>
Subject: [ovirt-users] Re: Sparse VMs from Templates - Storage issues
On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore <shantur.rathore(a)gmail.com> wrote:
Hi all,
I have a setup as detailed below
- iSCSI Storage Domain
- Template with Thin QCOW2 disk
- Multiple VMs from Template with Thin disk
Note that a single template disk used by many vms can become a performance bottleneck, and
is a single point of failure. Cloning the template when creating vms avoids such issues.
oVirt Node 4.4.4
4.4.4 is old, you should upgrade to 4.4.7.
When the VMs boots up it downloads some data to it and that leads to
increase in volume size.
I see that every few seconds the VM gets paused with
"VM X has been paused due to no Storage space error."
and then after few seconds
"VM X has recovered from paused back to up"
This is normal operation when a vm writes too quickly and oVirt cannot extend the disk
quick enough. To mitigate this, you can increase the volume chunk size.
Created this configuration drop in file:
# cat /etc/vdsm/vdsm.conf.d/99-local.conf
[irs]
volume_utilization_percent = 25
volume_utilization_chunk_mb = 2048
And restart vdsm.
With this setting, when free space in a disk is 1.5g, the disk will be extended by 2g.
With the default setting, when free space is 0.5g the disk was extended by 1g.
If this does not eliminate the pauses, try a larger chunk size like 4096.
Sometimes after a many pause and recovery the VM dies with
"VM X is down with error. Exit message: Lost connection with qemu process."
This means qemu has crashed. You can find more info in the vm log at:
/var/log/libvirt/qemu/vm-name.log
We know about bugs in qemu that cause such crashes when vm disk is extended. I think the
latest bug was fixed in 4.4.6, so upgrading to 4.4.7 will fix this issue.
Even with these settings, if you have a very bursty io in the vm, it may become paused.
The only way to completely avoid these pauses is to use a preallocated disk, or use file
storage (e.g. NFS). Preallocated disk can be thin provisioned on the server side so it
does not mean you need more storage, but you will not be able to use shared templates in
the way you use them now. You can create vm from template, but the template is cloned to
the new vm.
Another option with (still tech preview) is Managed Block Storage (Cinder based storage).
If your storage server is supported by Cinder, we can managed it using cinderlib. In this
setup every disk is a LUN, which may be thin provisioned on the storage server. This can
also offload storage operations to the server, like cloning disks, which may be much
faster and more efficient.
Nir
_______________________________________________
Users mailing list -- users(a)ovirt.org
To unsubscribe send an email to users-leave(a)ovirt.org Privacy Statement:
https://www.ovirt.org/privacy-policy.html
oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/W653KLDZMLU...
7:37 a.m.
So,
I did more digging and now I know how to reproduce it.
I created a VM and added a disk on local ssd using scratchpad hook,
formatted and mounted this scratchdisk.
Now, when I try to do heavy IO on this scratchdisk on local ssd, like,
dd if=/dev/zero of=/mnt/scratchdisk/test bs=1M count=10000, qemu
pauses VM.
Debug logs in libvirt shows
2021-09-23 11:04:32.765+0000: 463319: debug : virThreadJobSet:94 :
Thread 463319 (rpc-worker) is now running job
remoteDispatchNodeGetFreePages
2021-09-23 11:04:32.765+0000: 463319: debug : virNodeGetFreePages:1614
: conn=0x7f8620018ba0, npages=3, pages=0x7f8670009960,
startCell=4294967295, cellCount=1, counts=0x7f8670007db0, flags=0x0
2021-09-23 11:04:32.765+0000: 463319: debug : virThreadJobClear:119 :
Thread 463319 (rpc-worker) finished job remoteDispatchNodeGetFreePages
with ret=0
2021-09-23 11:04:34.235+0000: 488774: debug :
qemuMonitorJSONIOProcessLine:220 : Line [{"timestamp": {"seconds":
1632395074, "microseconds": 235454}, "event":
"BLOCK_IO_ERROR",
"data": {"device": "", "nospace": false,
"node-name":
"libvirt-3-format", "reason": "Input/output error",
"operation":
"write", "action": "stop"}}]
2021-09-23 11:04:34.235+0000: 488774: info :
qemuMonitorJSONIOProcessLine:235 : QEMU_MONITOR_RECV_EVENT:
mon=0x7f860c14b700 event={"timestamp": {"seconds": 1632395074,
"microseconds": 235454}, "event": "BLOCK_IO_ERROR",
"data": {"device":
"", "nospace": false, "node-name":
"libvirt-3-format", "reason":
"Input/output error", "operation": "write",
"action": "stop"}}
2021-09-23 11:04:34.235+0000: 488774: debug :
qemuMonitorJSONIOProcessEvent:181 : mon=0x7f860c14b700
obj=0x7f860c0e7450
2021-09-23 11:04:34.235+0000: 488774: debug :
qemuMonitorEmitEvent:1166 : mon=0x7f860c14b700 event=BLOCK_IO_ERROR
2021-09-23 11:04:34.235+0000: 488774: debug :
qemuProcessHandleEvent:581 : vm=0x7f86201d6df0
2021-09-23 11:04:34.235+0000: 488774: debug : virObjectEventNew:624 :
obj=0x7f860c0d82f0
2021-09-23 11:04:34.235+0000: 488774: debug :
qemuMonitorJSONIOProcessEvent:206 : handle BLOCK_IO_ERROR
handler=0x7f8639c77a90 data=0x7f860c0661c0
To confirm the local ssd is fine, have enough space where scratch disk
is located and I could run dd in host without any issues.
This happens on other storages as well.
So this seems like an issue with qemu when heavy IO is happening on a disk.
On Thu, Sep 23, 2021 at 7:19 AM Tommy Sway <sz_cuitao(a)163.com> wrote:
>
> Another option with (still tech preview) is Managed Block Storage (Cinder based
storage).
>
> It still tech preview in 4.4 ??
>
>
>
>
>
>
>
> -----Original Message-----
> From: users-bounces(a)ovirt.org <users-bounces(a)ovirt.org> On Behalf Of Nir
Soffer
> Sent: Wednesday, August 11, 2021 4:26 AM
> To: Shantur Rathore <shantur.rathore(a)gmail.com>
> Cc: users <users(a)ovirt.org>; Roman Bednar <rbednar(a)redhat.com>
> Subject: [ovirt-users] Re: Sparse VMs from Templates - Storage issues
>
> On Tue, Aug 10, 2021 at 4:24 PM Shantur Rathore <shantur.rathore(a)gmail.com>
wrote:
> >
> > Hi all,
> >
> > I have a setup as detailed below
> >
> > - iSCSI Storage Domain
> > - Template with Thin QCOW2 disk
> > - Multiple VMs from Template with Thin disk
>
> Note that a single template disk used by many vms can become a performance
bottleneck, and is a single point of failure. Cloning the template when creating vms
avoids such issues.
>
> > oVirt Node 4.4.4
>
> 4.4.4 is old, you should upgrade to 4.4.7.
>
> > When the VMs boots up it downloads some data to it and that leads to increase in
volume size.
> > I see that every few seconds the VM gets paused with
> >
> > "VM X has been paused due to no Storage space error."
> >
> > and then after few seconds
> >
> > "VM X has recovered from paused back to up"
>
> This is normal operation when a vm writes too quickly and oVirt cannot extend the
disk quick enough. To mitigate this, you can increase the volume chunk size.
>
> Created this configuration drop in file:
>
> # cat /etc/vdsm/vdsm.conf.d/99-local.conf
> [irs]
> volume_utilization_percent = 25
> volume_utilization_chunk_mb = 2048
>
> And restart vdsm.
>
> With this setting, when free space in a disk is 1.5g, the disk will be extended by
2g. With the default setting, when free space is 0.5g the disk was extended by 1g.
>
> If this does not eliminate the pauses, try a larger chunk size like 4096.
>
> > Sometimes after a many pause and recovery the VM dies with
> >
> > "VM X is down with error. Exit message: Lost connection with qemu
process."
>
> This means qemu has crashed. You can find more info in the vm log at:
> /var/log/libvirt/qemu/vm-name.log
>
> We know about bugs in qemu that cause such crashes when vm disk is extended. I think
the latest bug was fixed in 4.4.6, so upgrading to 4.4.7 will fix this issue.
>
> Even with these settings, if you have a very bursty io in the vm, it may become
paused. The only way to completely avoid these pauses is to use a preallocated disk, or
use file storage (e.g. NFS). Preallocated disk can be thin provisioned on the server side
so it does not mean you need more storage, but you will not be able to use shared
templates in the way you use them now. You can create vm from template, but the template
is cloned to the new vm.
>
> Another option with (still tech preview) is Managed Block Storage (Cinder based
storage). If your storage server is supported by Cinder, we can managed it using
cinderlib. In this setup every disk is a LUN, which may be thin provisioned on the storage
server. This can also offload storage operations to the server, like cloning disks, which
may be much faster and more efficient.
>
> Nir
> _______________________________________________
> Users mailing list -- users(a)ovirt.org
> To unsubscribe send an email to users-leave(a)ovirt.org Privacy Statement:
https://www.ovirt.org/privacy-policy.html
> oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/
> List Archives:
https://lists.ovirt.org/archives/list/users@ovirt.org/message/W653KLDZMLU...
>
1189
days inactive
1233
days old
13 comments
6 participants
participants (6)
-
Arik Hadas -
Benny Zlotnik -
Nir Soffer -
Shantur Rathore -
Tommy Sway -
Vojtech Juranek