10:01 a.m.
Hi All,
I've been trying to install latest ovirt node on IBM system X blade server
(UEFI based server) but not even able to start the installation.
I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from
http://ovirt.org/releases/3.1/tools/
Server boots up and detects the ISO, gives me initial screen of Install or
Upgrade / Reinstall etc. but the moment default install is selected (or it
goes into default if initial screen is not interrupted for 30 seconds.) -
it just waits for 3-4 seconds and the server is rebooted. These problem of
server reboot persist with any available option to install on the screen.
Note : I was able to successfully install RHEV-H and it worked fine. Not
sure why ovirt node installation is not even starting and goes into
infinite reboot loop with doing anything.
Out of curiosity - I tried this version of node as well
http://jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/...
that too resulted in same behavior.
Request Ovirt experts to assist and help resolve this issue.
Thanks & Regards,
Keyur
5:39 p.m.
Hello All,
Same is the case with Fedora install on this IBM server I am using.
Regards,
Keyur
On Fri, Nov 16, 2012 at 12:31 PM, Keyur Makwana <kurmakwana(a)gmail.com>wrote:
Hi All,
I've been trying to install latest ovirt node on IBM system X blade server
(UEFI based server) but not even able to start the installation.
I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from
http://ovirt.org/releases/3.1/tools/
Server boots up and detects the ISO, gives me initial screen of Install or
Upgrade / Reinstall etc. but the moment default install is selected (or it
goes into default if initial screen is not interrupted for 30 seconds.) -
it just waits for 3-4 seconds and the server is rebooted. These problem of
server reboot persist with any available option to install on the screen.
Note : I was able to successfully install RHEV-H and it worked fine. Not
sure why ovirt node installation is not even starting and goes into
infinite reboot loop with doing anything.
Out of curiosity - I tried this version of node as well
http://jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/...
that too resulted in same behavior.
Request Ovirt experts to assist and help resolve this issue.
Thanks & Regards,
Keyur
8:09 p.m.
Hello Ovirt Users,
Did anyone else also faced same issue or ovirt node not getting installed
and servers just reboots when option to install / upgrade / reinstall is
used.
Its on IBM system X server with UEFI. I've tried both latest Ovirt node and
Fedora 17 also. Both gives same behavior or just reboot in loop and nothing
else. I am unable to take ovirt further in my office at this moment.
Kindly advice.
Regards,
Keyur
On Fri, Nov 16, 2012 at 8:09 PM, Keyur Makwana <kurmakwana(a)gmail.com> wrote:
Hello All,
Same is the case with Fedora install on this IBM server I am using.
Regards,
Keyur
On Fri, Nov 16, 2012 at 12:31 PM, Keyur Makwana <kurmakwana(a)gmail.com>wrote:
> Hi All,
>
> I've been trying to install latest ovirt node on IBM system X blade
> server (UEFI based server) but not even able to start the installation.
>
> I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from
> http://ovirt.org/releases/3.1/tools/
>
> Server boots up and detects the ISO, gives me initial screen of Install
> or Upgrade / Reinstall etc. but the moment default install is selected (or
> it goes into default if initial screen is not interrupted for 30 seconds.)
> - it just waits for 3-4 seconds and the server is rebooted. These problem
> of server reboot persist with any available option to install on the screen.
>
> Note : I was able to successfully install RHEV-H and it worked fine. Not
> sure why ovirt node installation is not even starting and goes into
> infinite reboot loop with doing anything.
>
> Out of curiosity - I tried this version of node as well
>
http://jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/...
that too resulted in same behavior.
>
> Request Ovirt experts to assist and help resolve this issue.
>
> Thanks & Regards,
> Keyur
>
>
3:51 a.m.
--_3dede87b-3844-43eb-b692-ff4293a545fa_
Content-Type: text/plain; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
Node is based on Fedora 17=2C so if you have the same problem with both=2C =
that means it is likely upstream on the Fedora end of things. Fedora 18 is =
due to have support for UEFI=2C but release has been delayed until Jan 8th =
at the earliest. If Fedora 18 works=2C I'd say you'll likely be able to use=
an oVirt Node based on F18. Any way to disable UEFI on your server? - Nick
From: kurmakwana(a)gmail.com
Date: Sun=2C 18 Nov 2012 22:39:53 +0530
To: users(a)ovirt.org
Subject: Re: [Users] Unable to install ovirt node on IBM system X blade ser=
ver
Hello Ovirt Users=2C
Did anyone else also faced same issue or ovirt node not getting installed a=
nd servers just reboots when option to install / upgrade / reinstall is use=
d.
Its on IBM system X server with UEFI. I've tried both latest Ovirt node and=
Fedora 17 also. Both gives same behavior or just reboot in loop and nothin=
g else. I am unable to take ovirt further in my office at this moment.
=0A=
=0A=
Kindly advice.
Regards=2CKeyur
On Fri=2C Nov 16=2C 2012 at 8:09 PM=2C Keyur Makwana <kurmakwana(a)gmail.com>=
wrote:
=0A=
=0A=
Hello All=2C
Same is the case with Fedora install on this IBM server I am using.
=0A=
=0A=
Regards=2CKeyur
On Fri=2C Nov 16=2C 2012 at 12:31 PM=2C Keyur Makwana <kurmakwana(a)gmail.com=
<head <style><!--
.hmmessage P
{
margin:0px=3B
padding:0px
}
body.hmmessage
{
font-size: 12pt=3B
font-family:Calibri
}
--></style></head <body
class=3D'hmmessage'><div dir=3D'ltr'>Node is based on Fedora
17=2C so=
if you have the same problem with both=2C =3Bthat =3Bmeans it is l=
ikely upstream on the Fedora =3Bend of things. Fedora 18 is due to have=
support for UEFI=2C =3Bbut =3Brelease has been delayed until Jan 8=
th at the earliest. =3BIf Fedora 18 works=2C =3BI'd say
you'll =
=3Blikely be able to use an oVirt Node based on F18.<BR> =3B<BR>Any
way=
to disable =3BUEFI on your server?<BR> =3B<BR>-
Nick<br> =3B<B=
R><div><div id=3D"SkyDrivePlaceholder"></div><hr
id=3D"stopSpelling">From: =
kurmakwana(a)gmail.com<br>Date: Sun=2C 18 Nov 2012 22:39:53 +0530<br>To: user=
s(a)ovirt.org<br>Subject: Re: [Users] Unable to install ovirt node on IBM sys=
tem X blade server<br><br>Hello Ovirt
Users=2C<div><br></div><div>Did anyon=
e else also faced same issue or ovirt node not getting installed and server=
s just reboots when option to install / upgrade / reinstall is used.</div><=
div><br></div><div>Its on IBM system X server with UEFI. I've
tried both la=
test Ovirt node and Fedora 17 also. Both gives same behavior or just reboot=
in loop and nothing else. I am unable to take ovirt further in my office a=
t this moment.<br>=0A=
=0A=
<div><div class=3D"ecxgmail_extra"><br>Kindly
advice.</div><div class=3D"ec=
xgmail_extra"><br></div><div
class=3D"ecxgmail_extra">Regards=2C</div><div =
class=3D"ecxgmail_extra">Keyur</div><div
class=3D"ecxgmail_extra"><br><div =
class=3D"ecxgmail_quote">On Fri=2C Nov 16=2C 2012 at 8:09 PM=2C Keyur Makwa=
na <span dir=3D"ltr"><=3B<a
href=3D"mailto:kurmakwana@gmail.com">kurmakwa=
na(a)gmail.com</a>&gt=3B</span> wrote:<br>=0A=
=0A=
<blockquote style=3D"padding-left: 1ex=3B border-left-color: rgb(204=2C 204=
=2C 204)=3B border-left-width: 1px=3B border-left-style: solid=3B" class=3D=
"ecxgmail_quote">Hello All=2C<div><br></div><div>Same
is the case with Fedo=
ra install on this IBM server I am
using.</div><div><br></div>=0A=
<div>=0A=
Regards=2C</div><div>Keyur</div><div
class=3D"ecxgmail_extra"><br><br><div =
class=3D"ecxgmail_quote"><div class=3D"ecxim">On Fri=2C Nov
16=2C 2012 at 1=
2:31 PM=2C Keyur Makwana <span dir=3D"ltr"><=3B<a
href=3D"mailto:kurmakwa=
na@gmail.com">kurmakwana(a)gmail.com</a>&gt=3B</span>
wrote:<br>=0A=
=0A=
=0A=
</div><div><div class=3D"h5"><blockquote
style=3D"padding-left: 1ex=3B bord=
er-left-color: rgb(204=2C 204=2C 204)=3B border-left-width: 1px=3B border-l=
eft-style: solid=3B" class=3D"ecxgmail_quote">Hi
All=2C<div><br></div><div>=
I've been trying to install latest ovirt node on IBM system X blade server =
(UEFI based server) but not even able to start the installation.</div>=0A=
=0A=
=0A=
<div><br></div><div>I'm using latest image
ovirt-node-iso-2.5.5-0.1.fc17.is=
o from =3B<a href=3D"http://ovirt.org/releases/3.1/tools/"
target=3D"_b=
lank">http://ovirt.org/releases/3.1/tools/</a></div>=0A=
<div><br></div><div>Server boots up and detects the ISO=2C gives
me initial=
screen of Install or Upgrade / Reinstall etc. but the moment default insta=
ll is selected (or it goes into default if initial screen is not interrupte=
d for 30 seconds.) - it just waits for 3-4 seconds and the server is reboot=
ed. These problem of server reboot persist with any available option to ins=
tall on the screen.</div>=0A=
=0A=
=0A=
=0A=
<div><br></div><div>Note : I was able to successfully install
RHEV-H and it=
worked fine. Not sure why ovirt node installation is not even starting and=
goes into infinite reboot loop with doing
anything. =3B</div><div><br>=
</div>=0A=
=0A=
=0A=
=0A=
<div>Out of curiosity - I tried this version of node as well =3B<a href=
=3D"http://jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifac=
t/ovirt-node-iso-2.5.999-999.20121115114700git3d0fec5.446.fc17.iso" target=
=3D"_blank">http://jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild=
/artifact/ovirt-node-iso-2.5.999-999.20121115114700git3d0fec5.446.fc17.iso<=
/a> but that too resulted in same =3Bbehavior.</div>=0A=
=0A=
=0A=
=0A=
<div><br></div><div>Request Ovirt experts to assist and help
resolve this i=
ssue.</div><div><br></div><div>Thanks &=3B
Regards=2C</div><div>Keyur</d=
iv><div><br></div>=0A=
</blockquote></div></div></div><br></div>=0A=
</blockquote></div><br></div></div></div>=0A=
<br>_______________________________________________=0A=
Users mailing list=0A=
Users(a)ovirt.org=0A=
http://lists.ovirt.org/mailman/listinfo/users</div>
</div></body=
</html>=
--_3dede87b-3844-43eb-b692-ff4293a545fa_--
wrote:
=0A=
=0A=
=0A=
Hi All=2C
I've been trying to install latest ovirt node on IBM system X blade server =
(UEFI based server) but not even able to start the installation.=0A=
=0A=
=0A=
I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from http://ovirt.=
org/releases/3.1/tools/=0A=
Server boots up and detects the ISO=2C gives me initial screen of Install o=
r Upgrade / Reinstall etc. but the moment default install is selected (or i=
t goes into default if initial screen is not interrupted for 30 seconds.) -=
it just waits for 3-4 seconds and the server is rebooted. These problem of=
server reboot persist with any available option to install on the screen.=
=0A=
=0A=
=0A=
=0A=
Note : I was able to successfully install RHEV-H and it worked fine. Not su=
re why ovirt node installation is not even starting and goes into infinite =
reboot loop with doing anything.=20
=0A=
=0A=
=0A=
=0A=
Out of curiosity - I tried this version of node as well http://jenkins.ovir=
t.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/ovirt-node-iso-2.5.99=
9-999.20121115114700git3d0fec5.446.fc17.iso but that too resulted in same b=
ehavior.=0A=
=0A=
=0A=
=0A=
Request Ovirt experts to assist and help resolve this issue.
Thanks & Regards=2CKeyur
=0A=
=0A=
=0A=
_______________________________________________=0A=
Users mailing list=0A=
Users(a)ovirt.org=0A=
http://lists.ovirt.org/mailman/listinfo/users =
--_3dede87b-3844-43eb-b692-ff4293a545fa_
Content-Type: text/html; charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<html
4:15 p.m.
I've tested F17 on IBM bladeservers (HS20,HS21,HS22,HS22V) It's been
installed correctly with UEFI as well as with legacy.
Unfortunately I cannot check bladecenter with ovirt-node right now.
Which bladeserver have you tested?
--
Best regards, Pavel Zhukov
mailto:pavel@zhukoff.net
On Sun, 18 Nov 2012, Nicholas Kesick wrote:
Node is based on Fedora 17, so if you have the same problem with
both, that means it is likely upstream on the Fedora end of things. Fedora 18
is due to have support for UEFI, but release has been delayed until Jan 8th at
the earliest. If Fedora 18 works, I'd say you'll likely be able to use an oVirt
Node based on F18.
Any way to disable UEFI on your server?
- Nick
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
From: kurmakwana(a)gmail.com
Date: Sun, 18 Nov 2012 22:39:53 +0530
To: users(a)ovirt.org
Subject: Re: [Users] Unable to install ovirt node on IBM system X blade server
Hello Ovirt Users,
Did anyone else also faced same issue or ovirt node not getting installed and
servers just reboots when option to install / upgrade / reinstall is used.
Its on IBM system X server with UEFI. I've tried both latest Ovirt node and
Fedora 17 also. Both gives same behavior or just reboot in loop and nothing
else. I am unable to take ovirt further in my office at this moment.
Kindly advice.
Regards,
Keyur
On Fri, Nov 16, 2012 at 8:09 PM, Keyur Makwana <kurmakwana(a)gmail.com> wrote:
Hello All,
Same is the case with Fedora install on this IBM server I am using.
Regards,
Keyur
On Fri, Nov 16, 2012 at 12:31 PM, Keyur Makwana <kurmakwana(a)gmail.com>
wrote:
Hi All,
I've been trying to install latest ovirt node on IBM system X blade
server (UEFI based server) but not even able to start the installation.
I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from http://
ovirt.org/releases/3.1/tools/
Server boots up and detects the ISO, gives me initial screen of Install
or Upgrade / Reinstall etc. but the moment default install is selected
(or it goes into default if initial screen is not interrupted for 30
seconds.) - it just waits for 3-4 seconds and the server is rebooted.
These problem of server reboot persist with any available option to
install on the screen.
Note : I was able to successfully install RHEV-H and it worked fine.
Not sure why ovirt node installation is not even starting and goes into
infinite reboot loop with doing anything.
Out of curiosity - I tried this version of node as well http://
jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/
ovirt-node-iso-2.5.999-999.20121115114700git3d0fec5.446.fc17.iso but
that too resulted in same behavior.
Request Ovirt experts to assist and help resolve this issue.
Thanks & Regards,
Keyur
_______________________________________________ Users mailing list
Users(a)ovirt.org http://lists.ovirt.org/mailman/listinfo/users
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
4:19 p.m.
Hi,
That sounds good. I have HS22.
Regards,
Keyur
On Mon, Nov 19, 2012 at 6:45 PM, Pavel Zhukov <pavel(a)zhukoff.net> wrote:
I've tested F17 on IBM bladeservers (HS20,HS21,HS22,HS22V)
It's been
installed correctly with UEFI as well as with legacy.
Unfortunately I cannot check bladecenter with ovirt-node right now.
Which bladeserver have you tested?
--
Best regards, Pavel Zhukov
mailto:pavel@zhukoff.net
On Sun, 18 Nov 2012, Nicholas Kesick wrote:
> Node is based on Fedora 17, so if you have the same problem with
> both, that means it is likely upstream on the Fedora end of things.
Fedora 18
> is due to have support for UEFI, but release has been delayed until Jan
8th at
> the earliest. If Fedora 18 works, I'd say you'll likely be able to use
an oVirt
> Node based on F18.
>
> Any way to disable UEFI on your server?
>
> - Nick
>
>
━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
> From: kurmakwana(a)gmail.com
> Date: Sun, 18 Nov 2012 22:39:53 +0530
> To: users(a)ovirt.org
> Subject: Re: [Users] Unable to install ovirt node on IBM system X blade
server
>
> Hello Ovirt Users,
>
> Did anyone else also faced same issue or ovirt node not getting
installed and
> servers just reboots when option to install / upgrade / reinstall is
used.
>
> Its on IBM system X server with UEFI. I've tried both latest Ovirt node
and
> Fedora 17 also. Both gives same behavior or just reboot in loop and
nothing
> else. I am unable to take ovirt further in my office at this moment.
>
> Kindly advice.
>
> Regards,
> Keyur
>
> On Fri, Nov 16, 2012 at 8:09 PM, Keyur Makwana <kurmakwana(a)gmail.com>
wrote:
>
> Hello All,
>
> Same is the case with Fedora install on this IBM server I am using.
>
> Regards,
> Keyur
>
>
> On Fri, Nov 16, 2012 at 12:31 PM, Keyur Makwana <
kurmakwana(a)gmail.com>
> wrote:
>
> Hi All,
>
> I've been trying to install latest ovirt node on IBM system X
blade
> server (UEFI based server) but not even able to start the
installation.
>
> I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from
http://
> ovirt.org/releases/3.1/tools/
>
> Server boots up and detects the ISO, gives me initial screen of
Install
> or Upgrade / Reinstall etc. but the moment default install is
selected
> (or it goes into default if initial screen is not interrupted
for 30
> seconds.) - it just waits for 3-4 seconds and the server is
rebooted.
> These problem of server reboot persist with any available option
to
> install on the screen.
>
> Note : I was able to successfully install RHEV-H and it worked
fine.
> Not sure why ovirt node installation is not even starting and
goes into
> infinite reboot loop with doing anything.
>
> Out of curiosity - I tried this version of node as well http://
>
jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/
> ovirt-node-iso-2.5.999-999.20121115114700git3d0fec5.446.fc17.iso
but
> that too resulted in same behavior.
>
> Request Ovirt experts to assist and help resolve this issue.
>
> Thanks & Regards,
> Keyur
>
>
>
>
>
>
> _______________________________________________ Users mailing list
> Users(a)ovirt.org http://lists.ovirt.org/mailman/listinfo/users
> _______________________________________________
> Users mailing list
> Users(a)ovirt.org
> http://lists.ovirt.org/mailman/listinfo/users
4201
days inactive
4204
days old
5 comments
3 participants
participants (3)
-
Keyur Makwana -
Nicholas Kesick -
Pavel Zhukov