Network Setup after ovirt node Install and before add node to cluster
Hello, I ve downloaded an installed OVIRT NODE 4.2.7.1. During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp, both work) The installation passes and after the reboot ovirt node starts without any problems. BUT the network is not configured. I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ and I know https://www.ovirt.org/documentation/admin-guide/chap-Hosts/ and now I am between these two documents oVirt is installed but network is not configured to add it to datacenter of course I know the scripts under /etc/sysconfig/network-scripts do I really have do edit it manuel? if I change ip in command line ip a add … dev.. and ip route add … it fails to add node to datacenter - with one of the last version I ‘ve added the IP address in bash - added the host to datacenter, - after reboot readd the ip address in bash after reboot - an then I could change network settings in oVirt Manger What is best practices for adding a node to datacenter when the ip address is not assigned after installation Thx shb
On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb256@gmail.com> wrote:
Hello,
I ve downloaded an installed OVIRT NODE 4.2.7.1.
During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp, both work)
how did you setup the static ip? did you use Cockpit?
The installation passes and after the reboot ovirt node starts without any problems.
BUT the network is not configured.
what do you mean by 'network is not configured'? the static IP is not assigned to your selected NIC or sth else?
I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ and I know
https://www.ovirt.org/documentation/admin-guide/chap-Hosts/
and now I am between these two documents
oVirt is installed but network is not configured to add it to datacenter
of course I know the scripts under /etc/sysconfig/network-scripts
do I really have do edit it manuel?
if I change ip in command line
ip a add … dev..
and ip route add …
it fails to add node to datacenter
- with one of the last version I ‘ve added the IP address in bash
- added the host to datacenter,
- after reboot readd the ip address in bash after reboot
- an then I could change network settings in oVirt Manger
What is best practices for adding a node to datacenter when the ip address is not assigned after installation
Thx shb
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4SI62...
This happened to me too. The NIC doesn't come "up" on the first boot, even though it was initiated during the setup. DHCP or static makes no difference to this situation. iirc I used nmtui to bring the interface up and verify the hostname. Can't do it in cockpit without the interface being up... Once you're in the engine you can initialize and add the rest of the required nics. I'm not sure if this is as designed or a bug, but it last happened to me on 4.2.5, and was the same process on my 3 hosts. On Sun, Dec 9, 2018 at 12:14 AM Eitan Raviv <eraviv@redhat.com> wrote:
On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb256@gmail.com> wrote:
Hello,
I ve downloaded an installed OVIRT NODE 4.2.7.1.
During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp,
both work)
how did you setup the static ip? did you use Cockpit?
The installation passes and after the reboot ovirt node starts without any problems.
BUT the network is not configured.
what do you mean by 'network is not configured'? the static IP is not assigned to your selected NIC or sth else?
I know
https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ and I know
https://www.ovirt.org/documentation/admin-guide/chap-Hosts/
and now I am between these two documents
oVirt is installed but network is not configured to add it to datacenter
of course I know the scripts under /etc/sysconfig/network-scripts
do I really have do edit it manuel?
if I change ip in command line
ip a add … dev..
and ip route add …
it fails to add node to datacenter
- with one of the last version I ‘ve added the IP address in bash
- added the host to datacenter,
- after reboot readd the ip address in bash after reboot
- an then I could change network settings in oVirt Manger
What is best practices for adding a node to datacenter when the ip
address is not assigned after installation
Thx shb
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct:
https://www.ovirt.org/community/about/community-guidelines/
List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4SI62...
Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/PULDN5JRT6PZYV...
Ran into the same issue with oVirt Node 4.2.7.1 when installing as a virtual guest. Didi, Can you point us in the right direction? Thanks On Mon, Dec 10, 2018 at 2:23 AM Vincent Royer <vincent@epicenergy.ca> wrote:
This happened to me too.
The NIC doesn't come "up" on the first boot, even though it was initiated during the setup. DHCP or static makes no difference to this situation. iirc I used nmtui to bring the interface up and verify the hostname. Can't do it in cockpit without the interface being up...
Once you're in the engine you can initialize and add the rest of the required nics.
I'm not sure if this is as designed or a bug, but it last happened to me on 4.2.5, and was the same process on my 3 hosts.
On Sun, Dec 9, 2018 at 12:14 AM Eitan Raviv <eraviv@redhat.com> wrote:
On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb256@gmail.com> wrote:
Hello,
I ve downloaded an installed OVIRT NODE 4.2.7.1.
During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp, both work)
how did you setup the static ip? did you use Cockpit?
The installation passes and after the reboot ovirt node starts without any problems.
BUT the network is not configured.
what do you mean by 'network is not configured'? the static IP is not assigned to your selected NIC or sth else?
I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ and I know
https://www.ovirt.org/documentation/admin-guide/chap-Hosts/
and now I am between these two documents
oVirt is installed but network is not configured to add it to datacenter
of course I know the scripts under /etc/sysconfig/network-scripts
do I really have do edit it manuel?
if I change ip in command line
ip a add … dev..
and ip route add …
it fails to add node to datacenter
- with one of the last version I ‘ve added the IP address in bash
- added the host to datacenter,
- after reboot readd the ip address in bash after reboot
- an then I could change network settings in oVirt Manger
What is best practices for adding a node to datacenter when the ip address is not assigned after installation
Thx shb
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4SI62...
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/PULDN5JRT6PZYV...
On Mon, Dec 10, 2018 at 10:56 AM Eitan Raviv <eraviv@redhat.com> wrote:
Ran into the same issue with oVirt Node 4.2.7.1 when installing as a virtual guest. Didi, Can you point us in the right direction?
Sorry, I didn't try this myself recently and not sure about the details. Obviously it should all be automatic. Adding Simone. I suggest to open a bug about this and attach relevant logs (hosted-engine-setup logs, engine (and engine-setup) logs, vdsm, etc). Best regards,
Thanks On Mon, Dec 10, 2018 at 2:23 AM Vincent Royer <vincent@epicenergy.ca> wrote:
This happened to me too.
The NIC doesn't come "up" on the first boot, even though it was initiated during the setup. DHCP or static makes no difference to this situation. iirc I used nmtui to bring the interface up and verify the hostname. Can't do it in cockpit without the interface being up...
Once you're in the engine you can initialize and add the rest of the required nics.
I'm not sure if this is as designed or a bug, but it last happened to me on 4.2.5, and was the same process on my 3 hosts.
On Sun, Dec 9, 2018 at 12:14 AM Eitan Raviv <eraviv@redhat.com> wrote:
On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb256@gmail.com> wrote:
Hello,
I ve downloaded an installed OVIRT NODE 4.2.7.1.
During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp, both work)
how did you setup the static ip? did you use Cockpit?
The installation passes and after the reboot ovirt node starts without any problems.
BUT the network is not configured.
what do you mean by 'network is not configured'? the static IP is not assigned to your selected NIC or sth else?
I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ and I know
https://www.ovirt.org/documentation/admin-guide/chap-Hosts/
and now I am between these two documents
oVirt is installed but network is not configured to add it to datacenter
of course I know the scripts under /etc/sysconfig/network-scripts
do I really have do edit it manuel?
if I change ip in command line
ip a add … dev..
and ip route add …
it fails to add node to datacenter
- with one of the last version I ‘ve added the IP address in bash
- added the host to datacenter,
- after reboot readd the ip address in bash after reboot
- an then I could change network settings in oVirt Manger
What is best practices for adding a node to datacenter when the ip address is not assigned after installation
Thx shb
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4SI62...
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/PULDN5JRT6PZYV...
-- Didi
I think it's the installer/anaconda issue, the default is not to activate the network connection on boot. The same with RHEL/Centos I think, you have to remember to enable it in the check-box, it's quite annoying when your doing remote installs. Regards, Paul S. ________________________________________ From: Yedidyah Bar David <didi@redhat.com> Sent: 11 December 2018 10:22 To: Eitan Raviv; Simone Tiraboschi Cc: shb256@gmail.com; users Subject: [ovirt-users] Re: Network Setup after ovirt node Install and before add node to cluster On Mon, Dec 10, 2018 at 10:56 AM Eitan Raviv <eraviv@redhat.com> wrote:
Ran into the same issue with oVirt Node 4.2.7.1 when installing as a virtual guest. Didi, Can you point us in the right direction?
Sorry, I didn't try this myself recently and not sure about the details. Obviously it should all be automatic. Adding Simone. I suggest to open a bug about this and attach relevant logs (hosted-engine-setup logs, engine (and engine-setup) logs, vdsm, etc). Best regards,
Thanks On Mon, Dec 10, 2018 at 2:23 AM Vincent Royer <vincent@epicenergy.ca> wrote:
This happened to me too.
The NIC doesn't come "up" on the first boot, even though it was initiated during the setup. DHCP or static makes no difference to this situation. iirc I used nmtui to bring the interface up and verify the hostname. Can't do it in cockpit without the interface being up...
Once you're in the engine you can initialize and add the rest of the required nics.
I'm not sure if this is as designed or a bug, but it last happened to me on 4.2.5, and was the same process on my 3 hosts.
On Sun, Dec 9, 2018 at 12:14 AM Eitan Raviv <eraviv@redhat.com> wrote:
On Thu, Dec 6, 2018 at 7:10 PM Stefan Wolf <shb256@gmail.com> wrote:
Hello,
I ve downloaded an installed OVIRT NODE 4.2.7.1.
During the installation I ‘ve setup a static ip (I ‘ve also tried dhcp, both work)
how did you setup the static ip? did you use Cockpit?
The installation passes and after the reboot ovirt node starts without any problems.
BUT the network is not configured.
what do you mean by 'network is not configured'? the static IP is not assigned to your selected NIC or sth else?
I know https://www.ovirt.org/documentation/install-guide/chap-oVirt_Nodes/ and I know
https://www.ovirt.org/documentation/admin-guide/chap-Hosts/
and now I am between these two documents
oVirt is installed but network is not configured to add it to datacenter
of course I know the scripts under /etc/sysconfig/network-scripts
do I really have do edit it manuel?
if I change ip in command line
ip a add … dev..
and ip route add …
it fails to add node to datacenter
- with one of the last version I ‘ve added the IP address in bash
- added the host to datacenter,
- after reboot readd the ip address in bash after reboot
- an then I could change network settings in oVirt Manger
What is best practices for adding a node to datacenter when the ip address is not assigned after installation
Thx shb
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/TH5MRXJUU4SI62...
_______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/PULDN5JRT6PZYV...
-- Didi _______________________________________________ Users mailing list -- users@ovirt.org To unsubscribe send an email to users-leave@ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/TS4RHLMLC6KDKU... To view the terms under which this email is distributed, please go to:- http://leedsbeckett.ac.uk/disclaimer/email/
участники (5)
-
Eitan Raviv -
Staniforth, Paul -
Stefan Wolf -
Vincent Royer -
Yedidyah Bar David