Re: [Users] Unable to install ovirt node on IBM system X blade server

I've tested F17 on IBM bladeservers (HS20,HS21,HS22,HS22V) It's been installed correctly with UEFI as well as with legacy. Unfortunately I cannot check bladecenter with ovirt-node right now. Which bladeserver have you tested? -- Best regards, Pavel Zhukov mailto:pavel@zhukoff.net On Sun, 18 Nov 2012, Nicholas Kesick wrote: > Node is based on Fedora 17, so if you have the same problem with > both, that means it is likely upstream on the Fedora end of things. Fedora 18 > is due to have support for UEFI, but release has been delayed until Jan 8th at > the earliest. If Fedora 18 works, I'd say you'll likely be able to use an oVirt > Node based on F18. > > Any way to disable UEFI on your server? > > - Nick > > ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━ > From: kurmakwana(a)gmail.com > Date: Sun, 18 Nov 2012 22:39:53 +0530 > To: users(a)ovirt.org > Subject: Re: [Users] Unable to install ovirt node on IBM system X blade server > > Hello Ovirt Users, > > Did anyone else also faced same issue or ovirt node not getting installed and > servers just reboots when option to install / upgrade / reinstall is used. > > Its on IBM system X server with UEFI. I've tried both latest Ovirt node and > Fedora 17 also. Both gives same behavior or just reboot in loop and nothing > else. I am unable to take ovirt further in my office at this moment. > > Kindly advice. > > Regards, > Keyur > > On Fri, Nov 16, 2012 at 8:09 PM, Keyur Makwana <kurmakwana(a)gmail.com&gt; wrote: > > Hello All, > > Same is the case with Fedora install on this IBM server I am using. > > Regards, > Keyur > > > On Fri, Nov 16, 2012 at 12:31 PM, Keyur Makwana < kurmakwana(a)gmail.com&gt; > wrote: > > Hi All, > > I've been trying to install latest ovirt node on IBM system X blade > server (UEFI based server) but not even able to start the installation. > > I'm using latest image ovirt-node-iso-2.5.5-0.1.fc17.iso from http:// > ovirt.org/releases/3.1/tools/ > > Server boots up and detects the ISO, gives me initial screen of Install > or Upgrade / Reinstall etc. but the moment default install is selected > (or it goes into default if initial screen is not interrupted for 30 > seconds.) - it just waits for 3-4 seconds and the server is rebooted. > These problem of server reboot persist with any available option to > install on the screen. > > Note : I was able to successfully install RHEV-H and it worked fine. > Not sure why ovirt node installation is not even starting and goes into > infinite reboot loop with doing anything. > > Out of curiosity - I tried this version of node as well http:// > jenkins.ovirt.org/job/ovirt-node-iso/lastSuccessfulBuild/artifact/ > ovirt-node-iso-2.5.999-999.20121115114700git3d0fec5.446.fc17.iso but > that too resulted in same behavior. > > Request Ovirt experts to assist and help resolve this issue. > > Thanks & Regards, > Keyur > > > > > > > _______________________________________________ Users mailing list > Users(a)ovirt.org http://lists.ovirt.org/mailman/listinfo/users > _______________________________________________ > Users mailing list > Users(a)ovirt.org > http://lists.ovirt.org/mailman/listinfo/users