9:27 a.m.
I have noticed what seems to me to be a quirk, but wanted to see if
this is correct behaviour, or perhaps my configuration.
I am running a test install ov oVirt 3.3.2 in an all-in-one install.
My test box only has one physical NIC, so I am using that for
management/external network access, and I have create a dummy
interface called "dummy_0" to be used for the VMs.
I created four networks, each assigned their own VLAN (I am wanted to
simulate a "real-world" . I added the first network ("VLAN001") to
"dummy_0" with no problem (I was able to save the configuration). The
system created the "dummy_0.1".
When I tried to add another network ("VLAN002") to "dummy_0" and save
it, I got the following error:
--- START ---
Error while executing action:
local_host:
Cannot setup Networks. The following Network Interfaces were
specified more than once: dummy_0.1.
--- END ---
I found that in the "Setup Host Network" if I dragged "VLAN001" off
dummy_0 to the right under "Required", and left "VLAN002" on
"dummy_0", I could save it, and "VLAN001" appeared to remain active on
the host. Indeed, when I went back into "Setup Host Network", both
"VLAN001" and "VLAN002" were showing up on "dummy_0".
However, if I highlight "VLAN002" under "Networks" and click on the
"Hosts" tab, the "Network Interface" is showing a red down arrow,
indicating it is not up. The "Network Interface" for "VLAN001" is a
green up arrow. I have refreshed several times and at this point in
time, have left it for almost thirty minutes, but it remains as a red
down arrow. The same is true for the other two networks I tried
adding: I was able to add them as above, but they are also showing a
red down arrow.
My questions:
1.) Is doing what I had to do to add additional networks to an
interface normal, or is it a quirk of using a dummy interface?
2.) Any ideas why my additional networks are showing a red down
arrow? Again, maybe a quirk of using a dummy interface?
I am going to leave it overnight and see what happens (maybe some
background process needs to run??), but if that does not work, I am
sure I can scrounge up another NIC in the next couple of days and
install it into my test server to see if it does the same thing.
Thanks, in advance.
-Alan
9:32 a.m.
New subject: [Users] Error: "The following Network Interfaces were specified more than once:"
Please run:
"vdsClient -s 0 getVdsCaps"
And paste the output.
If this is caused by what I think is causing it, then this bug was fixed
during the 3.4 development cycle and is available in the 3.4 beta release.
(It affects dummy devices and VLANs).
Assaf Muller, Cloud Networking Engineer
Red Hat
----- Original Message -----
From: "Alan Murrell" <lists(a)murrell.ca>
To: users(a)ovirt.org
Sent: Wednesday, January 29, 2014 10:27:21 AM
Subject: [Users] Error: "The following Network Interfaces were specified more
than once:"
I have noticed what seems to me to be a quirk, but wanted to see if
this is correct behaviour, or perhaps my configuration.
I am running a test install ov oVirt 3.3.2 in an all-in-one install.
My test box only has one physical NIC, so I am using that for
management/external network access, and I have create a dummy
interface called "dummy_0" to be used for the VMs.
I created four networks, each assigned their own VLAN (I am wanted to
simulate a "real-world" . I added the first network ("VLAN001") to
"dummy_0" with no problem (I was able to save the configuration). The
system created the "dummy_0.1".
When I tried to add another network ("VLAN002") to "dummy_0" and save
it, I got the following error:
--- START ---
Error while executing action:
local_host:
Cannot setup Networks. The following Network Interfaces were
specified more than once: dummy_0.1.
--- END ---
I found that in the "Setup Host Network" if I dragged "VLAN001" off
dummy_0 to the right under "Required", and left "VLAN002" on
"dummy_0", I could save it, and "VLAN001" appeared to remain active on
the host. Indeed, when I went back into "Setup Host Network", both
"VLAN001" and "VLAN002" were showing up on "dummy_0".
However, if I highlight "VLAN002" under "Networks" and click on the
"Hosts" tab, the "Network Interface" is showing a red down arrow,
indicating it is not up. The "Network Interface" for "VLAN001" is a
green up arrow. I have refreshed several times and at this point in
time, have left it for almost thirty minutes, but it remains as a red
down arrow. The same is true for the other two networks I tried
adding: I was able to add them as above, but they are also showing a
red down arrow.
My questions:
1.) Is doing what I had to do to add additional networks to an
interface normal, or is it a quirk of using a dummy interface?
2.) Any ideas why my additional networks are showing a red down
arrow? Again, maybe a quirk of using a dummy interface?
I am going to leave it overnight and see what happens (maybe some
background process needs to run??), but if that does not work, I am
sure I can scrounge up another NIC in the next couple of days and
install it into my test server to see if it does the same thing.
Thanks, in advance.
-Alan
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
1:38 p.m.
On 29/01/14 10:27, Alan Murrell wrote:
I have noticed what seems to me to be a quirk, but wanted to see if
this
is correct behaviour, or perhaps my configuration.
I am running a test install ov oVirt 3.3.2 in an all-in-one install. My
test box only has one physical NIC, so I am using that for
management/external network access, and I have create a dummy interface
called "dummy_0" to be used for the VMs.
I created four networks, each assigned their own VLAN (I am wanted to
simulate a "real-world" . I added the first network ("VLAN001") to
"dummy_0" with no problem (I was able to save the configuration). The
system created the "dummy_0.1".
When I tried to add another network ("VLAN002") to "dummy_0" and
save
it, I got the following error:
--- START ---
Error while executing action:
local_host:
Cannot setup Networks. The following Network Interfaces were
specified more than once: dummy_0.1.
--- END ---
I found that in the "Setup Host Network" if I dragged "VLAN001" off
dummy_0 to the right under "Required", and left "VLAN002" on
"dummy_0",
I could save it, and "VLAN001" appeared to remain active on the host.
Indeed, when I went back into "Setup Host Network", both "VLAN001"
and
"VLAN002" were showing up on "dummy_0".
However, if I highlight "VLAN002" under "Networks" and click on the
"Hosts" tab, the "Network Interface" is showing a red down arrow,
indicating it is not up. The "Network Interface" for "VLAN001" is a
green up arrow. I have refreshed several times and at this point in
time, have left it for almost thirty minutes, but it remains as a red
down arrow. The same is true for the other two networks I tried adding:
I was able to add them as above, but they are also showing a red down
arrow.
My questions:
1.) Is doing what I had to do to add additional networks to an
interface normal, or is it a quirk of using a dummy interface?
2.) Any ideas why my additional networks are showing a red down
arrow? Again, maybe a quirk of using a dummy interface?
It's a quirk of oVirt at the moment :) The interface state as shown in
the GUI currently has very little to do with whether there's
connectivity on a network. There should be an open RFE for connectivity
indicators, though I can't seem to find it at the moment.
What it SHOULD tell you is whether a link is up or down on the host
("administrative state"), but according to this bug it doesn't even do
that (will be fixed soon):
https://bugzilla.redhat.com/show_bug.cgi?id=1038741
I am going to leave it overnight and see what happens (maybe some
background process needs to run??), but if that does not work, I am sure
I can scrounge up another NIC in the next couple of days and install it
into my test server to see if it does the same thing.
Thanks, in advance.
-Alan
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
3:58 p.m.
New subject: [Users] Error: "The following Network Interfaces were specified more than once:"
Quoting "Assaf Muller" <amuller(a)redhat.com>:
Please run:
"vdsClient -s 0 getVdsCaps"
Here you go:
--- START ---
HBAInventory = {'FC': [], 'iSCSI': [{'InitiatorName':
'iqn.1994-05.com.redhat:63b5586465eb'}]}
ISCSIInitiatorName = 'iqn.1994-05.com.redhat:63b5586465eb'
bondings = {'bond0': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond1': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond2': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond3': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond4': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []}}
bridges = {'VLAN001': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN001',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.1'],
'stp': 'off'},
'VLAN002': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN002',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.2'],
'stp': 'off'},
'VLAN009': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN009',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.9'],
'stp': 'off'},
'VLAN010': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN010',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.10'],
'stp': 'off'},
'ovirtmgmt': {'addr': '10.20.37.104',
'cfg': {'BOOTPROTO': 'dhcp',
'DEFROUTE': 'yes',
'DELAY': '0',
'DEVICE': 'ovirtmgmt',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '10.20.37.1',
'ipv6addrs':
['fe80::21e:c9ff:feea:46dc/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '255.255.255.0',
'ports': ['eth0'],
'stp': 'off'}}
clusterLevels = ['3.0', '3.1', '3.2', '3.3']
cpuCores = '2'
cpuFlags =
'fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,ht,tm,pbe,syscall,nx,lm,constant_tsc,arch_perfmon,pebs,bts,rep_good,aperfmperf,pni,dtes64,monitor,ds_cpl,vmx,tm2,ssse3,cx16,xtpr,pdcm,dca,lahf_lm,dts,tpr_shadow,vnmi,flexpriority,model_Conroe,model_coreduo,model_core2duo,model_n270'
cpuModel = 'Intel(R) Xeon(R) CPU 5110 @ 1.60GHz'
cpuSockets = '1'
cpuSpeed = '1595.818'
cpuThreads = '2'
emulatedMachines = ['rhel6.5.0',
'pc',
'rhel6.4.0',
'rhel6.3.0',
'rhel6.2.0',
'rhel6.1.0',
'rhel6.0.0',
'rhel5.5.0',
'rhel5.4.4',
'rhel5.4.0']
guestOverhead = '65'
hooks = {}
kvmEnabled = 'true'
lastClient = '10.20.37.104'
lastClientIface = 'ovirtmgmt'
management_ip = '0.0.0.0'
memSize = '15946'
netConfigDirty = 'False'
networks = {'VLAN001': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN001',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN001',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.1'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'VLAN002': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN002',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN002',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.2'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'VLAN009': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN009',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN009',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.9'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'VLAN010': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN010',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN010',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.10'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'ovirtmgmt': {'addr': '10.20.37.104',
'bridged': True,
'cfg': {'BOOTPROTO': 'dhcp',
'DEFROUTE': 'yes',
'DELAY': '0',
'DEVICE': 'ovirtmgmt',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '10.20.37.1',
'iface': 'ovirtmgmt',
'ipv6addrs':
['fe80::21e:c9ff:feea:46dc/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '255.255.255.0',
'ports': ['eth0'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'}}
nics = {'dummy_0': {'addr': '',
'cfg': {'DEVICE': 'dummy_0',
'HWADDR': '2e:cd:0e:e5:6a:65',
'MTU': '1500',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.1': {'addr': '',
'cfg': {'BRIDGE': 'VLAN001',
'DEVICE': 'dummy_0.1',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.10': {'addr': '',
'cfg': {'BRIDGE': 'VLAN010',
'DEVICE': 'dummy_0.10',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.2': {'addr': '',
'cfg': {'BRIDGE': 'VLAN002',
'DEVICE': 'dummy_0.2',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.9': {'addr': '',
'cfg': {'BRIDGE': 'VLAN009',
'DEVICE': 'dummy_0.9',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'eth0': {'addr': '',
'cfg': {'BRIDGE': 'ovirtmgmt',
'DEVICE': 'eth0',
'HWADDR': '00:1e:c9:ea:46:dc',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no'},
'hwaddr': '00:1e:c9:ea:46:dc',
'ipv6addrs': ['fe80::21e:c9ff:feea:46dc/64'],
'mtu': '1500',
'netmask': '',
'speed': 100}}
operatingSystem = {'name': 'RHEL', 'release':
'5.el6.centos.11.1', 'version': '6'}
packages2 = {'kernel': {'buildtime': 1385118909.0,
'release': '431.el6.x86_64',
'version': '2.6.32'},
'libvirt': {'buildtime': 1387360004,
'release': '29.el6_5.2',
'version': '0.10.2'},
'mom': {'buildtime': 1385055971, 'release':
'6.el6',
'version': '0.3.2'},
'qemu-img': {'buildtime': 1390980531,
'release': '2.416.el6',
'version': '0.12.1.2'},
'qemu-kvm': {'buildtime': 1390980531,
'release': '2.416.el6',
'version': '0.12.1.2'},
'spice-server': {'buildtime': 1386756528,
'release': '6.el6_5.1',
'version': '0.12.4'},
'vdsm': {'buildtime': 1390508936, 'release':
'2.el6',
'version': '4.13.3'}}
reservedMem = '321'
software_revision = '2'
software_version = '4.13'
supportedENGINEs = ['3.0', '3.1', '3.2', '3.3']
supportedProtocols = ['2.2', '2.3']
uuid = '44454C4C-5100-1031-804D-B2C04F4E4831'
version_name = 'Snow Man'
vlans = {'dummy_0.1': {'addr': '',
'cfg': {'BRIDGE': 'VLAN001',
'DEVICE': 'dummy_0.1',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 1},
'dummy_0.10': {'addr': '',
'cfg': {'BRIDGE': 'VLAN010',
'DEVICE': 'dummy_0.10',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 10},
'dummy_0.2': {'addr': '',
'cfg': {'BRIDGE': 'VLAN002',
'DEVICE': 'dummy_0.2',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 2},
'dummy_0.9': {'addr': '',
'cfg': {'BRIDGE': 'VLAN009',
'DEVICE': 'dummy_0.9',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 9}}
vmTypes = ['kvm']
--- END ---
-Alan
4:18 p.m.
New subject: [Users] Error: "The following Network Interfaces were specified more than once:"
Quoting "Lior Vernia" <lvernia(a)redhat.com>:
It's a quirk of oVirt at the moment :) The interface state as
shown in
the GUI currently has very little to do with whether there's
connectivity on a network. There should be an open RFE for connectivity
OK, so at this point it is a cosmetic issue as opposed to a functional one?
-Alan
4:36 p.m.
New subject: [Users] Error: "The following Network Interfaces were specified more than once:"
Thanks Alan, that confirms that it was the issue I had in mind.
This bug is fixed in oVirt 3.4, which has a first beta release out.
Assaf Muller, Cloud Networking Engineer
Red Hat
----- Original Message -----
From: "Alan Murrell" <lists(a)murrell.ca>
To: users(a)ovirt.org
Sent: Wednesday, January 29, 2014 4:58:59 PM
Subject: Re: [Users] Error: "The following Network Interfaces were specified more
than once:"
Quoting "Assaf Muller" <amuller(a)redhat.com>:
Please run:
"vdsClient -s 0 getVdsCaps"
Here you go:
--- START ---
HBAInventory = {'FC': [], 'iSCSI': [{'InitiatorName':
'iqn.1994-05.com.redhat:63b5586465eb'}]}
ISCSIInitiatorName = 'iqn.1994-05.com.redhat:63b5586465eb'
bondings = {'bond0': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond1': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond2': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond3': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []},
'bond4': {'addr': '',
'cfg': {},
'hwaddr': '00:00:00:00:00:00',
'ipv6addrs': [],
'mtu': '1500',
'netmask': '',
'slaves': []}}
bridges = {'VLAN001': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN001',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.1'],
'stp': 'off'},
'VLAN002': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN002',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.2'],
'stp': 'off'},
'VLAN009': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN009',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.9'],
'stp': 'off'},
'VLAN010': {'addr': '',
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN010',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.10'],
'stp': 'off'},
'ovirtmgmt': {'addr': '10.20.37.104',
'cfg': {'BOOTPROTO': 'dhcp',
'DEFROUTE': 'yes',
'DELAY': '0',
'DEVICE': 'ovirtmgmt',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '10.20.37.1',
'ipv6addrs':
['fe80::21e:c9ff:feea:46dc/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '255.255.255.0',
'ports': ['eth0'],
'stp': 'off'}}
clusterLevels = ['3.0', '3.1', '3.2', '3.3']
cpuCores = '2'
cpuFlags =
'fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,ht,tm,pbe,syscall,nx,lm,constant_tsc,arch_perfmon,pebs,bts,rep_good,aperfmperf,pni,dtes64,monitor,ds_cpl,vmx,tm2,ssse3,cx16,xtpr,pdcm,dca,lahf_lm,dts,tpr_shadow,vnmi,flexpriority,model_Conroe,model_coreduo,model_core2duo,model_n270'
cpuModel = 'Intel(R) Xeon(R) CPU 5110 @ 1.60GHz'
cpuSockets = '1'
cpuSpeed = '1595.818'
cpuThreads = '2'
emulatedMachines = ['rhel6.5.0',
'pc',
'rhel6.4.0',
'rhel6.3.0',
'rhel6.2.0',
'rhel6.1.0',
'rhel6.0.0',
'rhel5.5.0',
'rhel5.4.4',
'rhel5.4.0']
guestOverhead = '65'
hooks = {}
kvmEnabled = 'true'
lastClient = '10.20.37.104'
lastClientIface = 'ovirtmgmt'
management_ip = '0.0.0.0'
memSize = '15946'
netConfigDirty = 'False'
networks = {'VLAN001': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN001',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN001',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.1'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'VLAN002': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN002',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN002',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.2'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'VLAN009': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN009',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN009',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.9'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'VLAN010': {'addr': '',
'bridged': True,
'cfg': {'DEFROUTE': 'no',
'DELAY': '0',
'DEVICE': 'VLAN010',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '0.0.0.0',
'iface': 'VLAN010',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '',
'ports': ['dummy_0.10'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'},
'ovirtmgmt': {'addr': '10.20.37.104',
'bridged': True,
'cfg': {'BOOTPROTO': 'dhcp',
'DEFROUTE': 'yes',
'DELAY': '0',
'DEVICE': 'ovirtmgmt',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'TYPE': 'Bridge'},
'gateway': '10.20.37.1',
'iface': 'ovirtmgmt',
'ipv6addrs':
['fe80::21e:c9ff:feea:46dc/64'],
'ipv6gateway': '::',
'mtu': '1500',
'netmask': '255.255.255.0',
'ports': ['eth0'],
'qosInbound': '',
'qosOutbound': '',
'stp': 'off'}}
nics = {'dummy_0': {'addr': '',
'cfg': {'DEVICE': 'dummy_0',
'HWADDR': '2e:cd:0e:e5:6a:65',
'MTU': '1500',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.1': {'addr': '',
'cfg': {'BRIDGE': 'VLAN001',
'DEVICE': 'dummy_0.1',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.10': {'addr': '',
'cfg': {'BRIDGE': 'VLAN010',
'DEVICE': 'dummy_0.10',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.2': {'addr': '',
'cfg': {'BRIDGE': 'VLAN002',
'DEVICE': 'dummy_0.2',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'dummy_0.9': {'addr': '',
'cfg': {'BRIDGE': 'VLAN009',
'DEVICE': 'dummy_0.9',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'hwaddr': '2e:cd:0e:e5:6a:65',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'speed': 0},
'eth0': {'addr': '',
'cfg': {'BRIDGE': 'ovirtmgmt',
'DEVICE': 'eth0',
'HWADDR': '00:1e:c9:ea:46:dc',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no'},
'hwaddr': '00:1e:c9:ea:46:dc',
'ipv6addrs': ['fe80::21e:c9ff:feea:46dc/64'],
'mtu': '1500',
'netmask': '',
'speed': 100}}
operatingSystem = {'name': 'RHEL', 'release':
'5.el6.centos.11.1', 'version': '6'}
packages2 = {'kernel': {'buildtime': 1385118909.0,
'release': '431.el6.x86_64',
'version': '2.6.32'},
'libvirt': {'buildtime': 1387360004,
'release': '29.el6_5.2',
'version': '0.10.2'},
'mom': {'buildtime': 1385055971, 'release':
'6.el6',
'version': '0.3.2'},
'qemu-img': {'buildtime': 1390980531,
'release': '2.416.el6',
'version': '0.12.1.2'},
'qemu-kvm': {'buildtime': 1390980531,
'release': '2.416.el6',
'version': '0.12.1.2'},
'spice-server': {'buildtime': 1386756528,
'release': '6.el6_5.1',
'version': '0.12.4'},
'vdsm': {'buildtime': 1390508936, 'release':
'2.el6',
'version': '4.13.3'}}
reservedMem = '321'
software_revision = '2'
software_version = '4.13'
supportedENGINEs = ['3.0', '3.1', '3.2', '3.3']
supportedProtocols = ['2.2', '2.3']
uuid = '44454C4C-5100-1031-804D-B2C04F4E4831'
version_name = 'Snow Man'
vlans = {'dummy_0.1': {'addr': '',
'cfg': {'BRIDGE': 'VLAN001',
'DEVICE': 'dummy_0.1',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 1},
'dummy_0.10': {'addr': '',
'cfg': {'BRIDGE': 'VLAN010',
'DEVICE': 'dummy_0.10',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs':
['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 10},
'dummy_0.2': {'addr': '',
'cfg': {'BRIDGE': 'VLAN002',
'DEVICE': 'dummy_0.2',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 2},
'dummy_0.9': {'addr': '',
'cfg': {'BRIDGE': 'VLAN009',
'DEVICE': 'dummy_0.9',
'NM_CONTROLLED': 'no',
'ONBOOT': 'yes',
'STP': 'no',
'VLAN': 'yes'},
'iface': 'dummy_0',
'ipv6addrs': ['fe80::2ccd:eff:fee5:6a65/64'],
'mtu': '1500',
'netmask': '',
'vlanid': 9}}
vmTypes = ['kvm']
--- END ---
-Alan
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
1:16 p.m.
New subject: [Users] Error: "The following Network Interfaces were specified more than once:"
On 29/01/14 17:18, Alan Murrell wrote:
Quoting "Lior Vernia" <lvernia(a)redhat.com>:
> It's a quirk of oVirt at the moment :) The interface state as shown in
> the GUI currently has very little to do with whether there's
> connectivity on a network. There should be an open RFE for connectivity
OK, so at this point it is a cosmetic issue as opposed to a functional one?
It's a little of both. It is a cosmetic issue if you're looking to see
the link state, functional if you were expecting it to tell you whether
there's layer 3 connectivity.
-Alan
_______________________________________________
Users mailing list
Users(a)ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
3760
days inactive
3761
days old
6 comments
3 participants
participants (3)
-
Alan Murrell -
Assaf Muller -
Lior Vernia