iSCSI multipath issue
by Nick Kas
Hello evryone,
setup ovirt 4.4.1 on CentOS 8.2 as an experiment, and I am trying to get an iSCSI domain working but have issues. The little experimental cluster has 3 hosts. There is an ovirtmgmt network on the default vlan, and two iSCSI network (172.27.0/1.X) with vlans 20/21. ovirtmgmt has all the functions (Data, display, migration etc), and the iSCSI networks nothing yet, and they are not set as required.
The SAN device is already serving a few iSCSI volumes to a vmware cluster, so I know things are fine on this end. It has two controllers, and four NICs per controller so a total of 8 NICs, half of the NICS per controller on 172.27.0.X and half on 172.27.1.X.
When I create the iSCSI domain, I login to only one of the targets, and add the Volume, all is good and I can use the disc fine.
However when I login to more than one of the targets, then I start having issues with the Volume. Even when I enabled multipath in the cluster, and I created a single multipath by selecting both of the 172.27.0/1.X networks, and all the targets, the end result was the same. The hosts have difficulty accessing the volume, they may even swing between 'non-operational' and 'up' if I transfer data to the volume. When I ssh to the hosts and i check things in the command line I also get inconsistent results between hosts, and blocks that appear with lsblk when I first setup iSCSI have dissapeared after I try to actively use the volume.
I am new to iSCSI so I am not sure how to debug this. I am not sure if my multipath configuration is correct or not. The documentation on this part was not very detailed. I also tried to remove the domain, and try to experiment with mounting the iSCSI volume from the command line, but I cannot even discover the target from the command line, which is very bizarre. The command
iscsiadm --mode discovery --target sendtargets --portal 172.27.0.55 --discover
returns the message 'iscsiadm: cannot make connection to 172.27.0.55: No route to host'. Yet through ovirt, and if I select only one target, everything work fine!
Any suggestions on how to start debugging this would really be appreciated.
4 years, 7 months
Error exporting into ova
by Gianluca Cecchi
Hello,
I'm playing with export_vm_as_ova.py downloaded from the examples github:
https://github.com/oVirt/ovirt-engine-sdk/blob/master/sdk/examples/export...
My environment is oVirt 4.3.3.7 with iSCSI storage domain.
It fails leaving an ova.tmp file
In webadmin gui:
Starting to export Vm enginecopy1 as a Virtual Appliance
7/19/1911:55:12 AM
VDSM ov301 command TeardownImageVDS failed: Cannot deactivate Logical
Volume: ('General Storage Exception: ("5 [] [\' Logical volume
fa33df49-b09d-4f86-9719-ede649542c21/0420ef47-0ad0-4cf9-babd-d89383f7536b
in
use.\']\\nfa33df49-b09d-4f86-9719-ede649542c21/[\'a7480dc5-b5ca-4cb3-986d-77bc12165be4\',
\'0420ef47-0ad0-4cf9-babd-d89383f7536b\']",)',)
7/19/1912:25:36 PM
Failed to export Vm enginecopy1 as a Virtual Appliance to path
/save_ova/base/dump/myvm2.ova on Host ov301
7/19/1912:25:37 PM
During export I have this qemu-img process creating the disk over the loop
device:
root 30878 30871 0 11:55 pts/2 00:00:00 su -p -c qemu-img convert
-T none -O qcow2
'/rhev/data-center/mnt/blockSD/fa33df49-b09d-4f86-9719-ede649542c21/images/59a4a324-4c99-4ff5-abb1-e9bbac83292a/0420ef47-0ad0-4cf9-babd-d89383f7536b'
'/dev/loop1' vdsm
vdsm 30882 30878 10 11:55 ? 00:00:00 qemu-img convert -T none -O
qcow2
/rhev/data-center/mnt/blockSD/fa33df49-b09d-4f86-9719-ede649542c21/images/59a4a324-4c99-4ff5-abb1-e9bbac83292a/0420ef47-0ad0-4cf9-babd-d89383f7536b
/dev/loop1
The ova.tmp file is getting filled while command runs
eg:
[root@ov301 ]# du -sh /save_ova/base/dump/myvm2.ova.tmp
416M /save_ova/base/dump/myvm2.ova.tmp
[root@ov301 sysctl.d]#
[root@ov301 sysctl.d]# du -sh /save_ova/base/dump/myvm2.ova.tmp
911M /save_ova/base/dump/myvm2.ova.tmp
[root@ov301 ]#
and the final generated / not completed file is in this state:
[root@ov301 ]# qemu-img info /save_ova/base/dump/myvm2.ova.tmp
image: /save_ova/base/dump/myvm2.ova.tmp
file format: raw
virtual size: 30G (32217446400 bytes)
disk size: 30G
[root@ov301 sysctl.d]#
But I notice that the timestamp of the file is about 67 minutes after start
of job and well after the notice of its failure....
[root@ov301 sysctl.d]# ll /save_ova/base/dump/
total 30963632
-rw-------. 1 root root 32217446400 Jul 19 13:02 myvm2.ova.tmp
[root@ov301 sysctl.d]#
[root@ov301 sysctl.d]# du -sh /save_ova/base/dump/myvm2.ova.tmp
30G /save_ova/base/dump/myvm2.ova.tmp
[root@ov301 sysctl.d]#
In engine.log the first error I see is 30 minutes after start
2019-07-19 12:25:31,563+02 ERROR
[org.ovirt.engine.core.common.utils.ansible.AnsibleExecutor]
(EE-ManagedThreadFactory-engineScheduled-Thread-64) [2001ddf4] Ansible
playbook execution failed: Timeout occurred while executing Ansible
playbook.
2019-07-19 12:25:31,563+02 INFO
[org.ovirt.engine.core.common.utils.ansible.AnsibleExecutor]
(EE-ManagedThreadFactory-engineScheduled-Thread-64) [2001ddf4] Ansible
playbook command has exited with value: 1
2019-07-19 12:25:31,564+02 ERROR
[org.ovirt.engine.core.bll.CreateOvaCommand]
(EE-ManagedThreadFactory-engineScheduled-Thread-64) [2001ddf4] Failed to
create OVA. Please check logs for more details:
/var/log/ovirt-engine/ova/ovirt-export-ova-ansible-20190719115531-ov301-2001ddf4.log
2019-07-19 12:25:31,565+02 INFO
[org.ovirt.engine.core.vdsbroker.vdsbroker.TeardownImageVDSCommand]
(EE-ManagedThreadFactory-engineScheduled-Thread-64) [2001ddf4] START,
TeardownImageVDSCommand(HostName = ov301,
ImageActionsVDSCommandParameters:{hostId='8ef1ce6f-4e38-486c-b3a4-58235f1f1d06'}),
log id: 3d2246f7
2019-07-19 12:25:36,569+02 ERROR
[org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLogDirector]
(EE-ManagedThreadFactory-engineScheduled-Thread-64) [2001ddf4] EVENT_ID:
VDS_BROKER_COMMAND_FAILURE(10,802), VDSM ov301 command TeardownImageVDS
failed: Cannot deactivate Logical Volume: ('General Storage Exception: ("5
[] [\' Logical volume
fa33df49-b09d-4f86-9719-ede649542c21/0420ef47-0ad0-4cf9-babd-d89383f7536b
in
use.\']\\nfa33df49-b09d-4f86-9719-ede649542c21/[\'a7480dc5-b5ca-4cb3-986d-77bc12165be4\',
\'0420ef47-0ad0-4cf9-babd-d89383f7536b\']",)',)
In ansible playbook suggested log file I don't see anything useful.
It ends with timestamps when the script has been launched.
Last lines are:
2019-07-19 11:55:33,877 p=5699 u=ovirt | TASK [ovirt-ova-export-pre-pack :
Retrieving the temporary path for the OVA file] ***
2019-07-19 11:55:34,198 p=5699 u=ovirt | changed: [ov301] => {
"changed": true,
"dest": "/save_ova/base/dump/myvm2.ova.tmp",
"gid": 0,
"group": "root",
"mode": "0600",
"owner": "root",
"secontext": "system_u:object_r:nfs_t:s0",
"size": 32217446912,
"state": "file",
"uid": 0
}
2019-07-19 11:55:34,204 p=5699 u=ovirt | TASK [ovirt-ova-pack : Run
packing script] *************************************
It seems 30 minutes... for timeout? About what, ansible job?
Or possibly implicit user session created when running the python script?
The snapshot has been correctly deleted (as I see also in engine.log), I
don't see it in webadmin gui.
Any known problem?
Just for test I executed again at 14:24 and I see same Ansible error at
14:54
The snapshot gets deleted, while the qemu-img command still continues....
[root@ov301 sysctl.d]# ps -ef | grep qemu-img
root 13504 13501 0 14:24 pts/1 00:00:00 su -p -c qemu-img convert
-T none -O qcow2
'/rhev/data-center/mnt/blockSD/fa33df49-b09d-4f86-9719-ede649542c21/images/59a4a324-4c99-4ff5-abb1-e9bbac83292a/0420ef47-0ad0-4cf9-babd-d89383f7536b'
'/dev/loop0' vdsm
vdsm 13505 13504 3 14:24 ? 00:01:26 qemu-img convert -T none -O
qcow2
/rhev/data-center/mnt/blockSD/fa33df49-b09d-4f86-9719-ede649542c21/images/59a4a324-4c99-4ff5-abb1-e9bbac83292a/0420ef47-0ad0-4cf9-babd-d89383f7536b
/dev/loop0
root 17587 24530 0 15:05 pts/0 00:00:00 grep --color=auto qemu-img
[root@ov301 sysctl.d]#
[root@ov301 sysctl.d]# du -sh /save_ova/base/dump/myvm2.ova.tmp
24G /save_ova/base/dump/myvm2.ova.tmp
[root@ov301 sysctl.d]# ll /save_ova/base/dump/myvm2.ova.tmp
-rw-------. 1 root root 32217446400 Jul 19 15:14
/save_ova/base/dump/myvm2.ova.tmp
[root@ov301 sysctl.d]#
and then continues until image copy completes, but at this time the job has
already aborted and so the completion of the ova composition doesn't go
ahead... and I remain with the ova.tmp file...
How to extend timeout?
Thanks in advance,
Gianluca
4 years, 7 months
deprecating export domain?
by Charles Kozler
Hello,
I recently read on this list from a redhat member that export domain is
either being deprecated or looking at being deprecated
To that end, can you share details? Can you share any notes/postings/bz's
that document this? I would imagine something like this would be discussed
in larger audience
This seems like a somewhat significant change to make and I am curious
where this is scheduled? Currently, a lot of my backups rely explicitly on
an export domain for online snapshots, so I'd like to plan accordingly
Thanks!
4 years, 7 months
Upgrade Memory of oVirt Nodes
by souvaliotimaria＠mail.com
Hello everyone,
I have an oVirt 4.3.2.5 hyperconverged 3 node production environment and we want to add some RAM to it.
Can I upgrade the RAM without my users noticing any disruptions and keep the VMs running?
The way I thought I should do it was to migrate any running VMs to the other nodes, then set one node in maintenance mode, shut it down, place the new memory, bring it back up, remove it from maintenance mode and see how the installation reacts and repeat for the other two nodes. Is this correct or should I follow another way?
Will there be a problem during the time when the nodes will not be identical in their resources?
Thank you for your time,
Souvalioti Maria
4 years, 8 months
Support for Shared SAS storage
by Vinícius Ferrão
Hello,
I’ve two compute nodes with SAS Direct Attached sharing the same disks.
Looking at the supported types I can’t see this on the documentation: https://www.ovirt.org/documentation/admin-guide/chap-Storage.html
There’s is local storage on this documentation, but my case is two machines, both using SAS, connected to the same machines. It’s the VRTX hardware from Dell.
Is there any support for this? It should be just like Fibre Channel and iSCSI, but with SAS instead.
Thanks,
4 years, 8 months
oVirt 4.4.0 Release is now generally available
by Sandro Bonazzola
oVirt 4.4.0 Release is now generally available
The oVirt Project is excited to announce the general availability of the
oVirt 4.4.0 Release, as of May 20th, 2020
This release unleashes an altogether more powerful and flexible open source
virtualization solution that encompasses hundreds of individual changes and
a wide range of enhancements across the engine, storage, network, user
interface, and analytics, as compared to oVirt 4.3.
Important notes before you install / upgrade
Some of the features included in the oVirt 4.4.0 release require content
that will be available in CentOS Linux 8.2 but cannot be tested on RHEL 8.2
yet due to some incompatibility in the openvswitch package that is shipped
in CentOS Virt SIG, which requires rebuilding openvswitch on top of CentOS
8.2. The cluster switch type OVS is not implemented for CentOS 8 hosts.
Please note that oVirt 4.4 only supports clusters and datacenters with
compatibility version 4.2 and above. If clusters or datacenters are running
with an older compatibility version, you need to upgrade them to at least
4.2 (4.3 is recommended).
Please note that in RHEL 8 / CentOS 8 several devices that worked on EL7
are no longer supported.
For example, megaraid_sas driver is removed. If you use Enterprise Linux 8
hosts you can try to provide the necessary drivers for the deprecated
hardware using the DUD method (See users mailing list thread on this at
https://lists.ovirt.org/archives/list/users@ovirt.org/thread/NDSVUZSESOXE...
)
Installation instructions
For the engine: either use the oVirt appliance or install CentOS Linux 8
minimal by following these steps:
- Install the CentOS Linux 8 image from
http://centos.mirror.garr.it/centos/8.1.1911/isos/x86_64/CentOS-8.1.1911-...
- dnf install https://resources.ovirt.org/pub/yum-repo/ovirt-release44.rpm
- dnf update (reboot if needed)
- dnf module enable -y javapackages-tools pki-deps postgresql:12
- dnf install ovirt-engine
- engine-setup
For the nodes:
Either use oVirt Node ISO or:
- Install CentOS Linux 8 from
http://centos.mirror.garr.it/centos/8.1.1911/isos/x86_64/CentOS-8.1.1911-...,
selecting the minimal installation.
- dnf install https://resources.ovirt.org/pub/yum-repo/ovirt-release44.rpm
- dnf update (reboot if needed)
- Attach the host to the engine and let it be deployed.
Update instructionsUpdate from oVirt 4.4 Release Candidate
On the engine side and on CentOS hosts, you’ll need to switch from
ovirt44-pre to ovirt44 repositories.
In order to do so, you need to:
1.
dnf remove ovirt-release44-pre
2.
rm -f /etc/yum.repos.d/ovirt-4.4-pre-dependencies.repo
3.
rm -f /etc/yum.repos.d/ovirt-4.4-pre.repo
4.
dnf install https://resources.ovirt.org/pub/yum-repo/ovirt-release44.rpm
5.
dnf update
On the engine side you’ll need to run engine-setup only if you were not
already on the latest release candidate.
On oVirt Node, you’ll need to upgrade with:
1.
Move node to maintenance
2.
dnf install
https://resources.ovirt.org/pub/ovirt-4.4/rpm/el8/noarch/ovirt-node-ng-im...
3.
Reboot
4.
Activate the host
Update from oVirt 4.3
oVirt 4.4 is available only for CentOS 8. In-place upgrades from previous
installations, based on CentOS 7, are not possible. For the engine, use
backup, and restore that into a new engine. Nodes will need to be
reinstalled.
A 4.4 engine can still manage existing 4.3 hosts, but you can’t add new
ones.
For a standalone engine, please refer to upgrade procedure at
https://ovirt.org/documentation/upgrade_guide/#Upgrading_from_4-3
If needed, run ovirt-engine-rename (see engine rename tool documentation at
https://www.ovirt.org/documentation/admin-guide/chap-Utilities.html )
When upgrading hosts:
You need to upgrade one host at a time.
1.
Turn host to maintenance. Virtual machines on that host should migrate
automatically to a different host.
2.
Remove it from the engine
3.
Re-install it with el8 or oVirt Node as per installation instructions
4.
Re-add the host to the engine
Please note that you may see some issues live migrating VMs from el7 to
el8. If you hit such a case, please turn off the vm on el7 host and get it
started on the new el8 host in order to be able to move the next el7 host
to maintenance.
What’s new in oVirt 4.4.0 Release?
-
Hypervisors based on CentOS Linux 8 (rebuilt from award winning RHEL8),
for both oVirt Node and standalone CentOS Linux hosts.
-
Easier network management and configuration flexibility with
NetworkManager.
-
VMs based on a more modern Q35 chipset with legacy SeaBIOS and UEFI
firmware.
-
Support for direct passthrough of local host disks to VMs.
-
Live migration improvements for High Performance guests.
-
New Windows guest tools installer based on WiX framework now moved to
VirtioWin project.
-
Dropped support for cluster level prior to 4.2.
-
Dropped API/SDK v3 support deprecated in past versions.
-
4K block disk support only for file-based storage. iSCSI/FC storage do
not support 4K disks yet.
-
You can export a VM to a data domain.
-
You can edit floating disks.
-
Ansible Runner (ansible-runner) is integrated within the engine,
enabling more detailed monitoring of playbooks executed from the engine.
-
Adding and reinstalling hosts is now completely based on Ansible,
replacing ovirt-host-deploy, which is not used anymore.
-
The OpenStack Neutron Agent cannot be configured by oVirt anymore, it
should be configured by TripleO instead.
This release is available now on x86_64 architecture for:
* Red Hat Enterprise Linux 8.1
* CentOS Linux (or similar) 8.1
This release supports Hypervisor Hosts on x86_64 and ppc64le architectures
for:
* Red Hat Enterprise Linux 8.1
* CentOS Linux (or similar) 8.1
* oVirt Node 4.4 based on CentOS Linux 8.1 (available for x86_64 only)
See the release notes [1] for installation instructions and a list of new
features and bugs fixed.
If you manage more than one oVirt instance, OKD or RDO we also recommend to
try ManageIQ <http://manageiq.org/>.
In such a case, please be sure to take the qc2 image and not the ova image.
Notes:
- oVirt Appliance is already available for CentOS Linux 8
- oVirt Node NG is already available for CentOS Linux 8
Additional Resources:
* Read more about the oVirt 4.4.0 release highlights:
http://www.ovirt.org/release/4.4.0/
* Get more oVirt project updates on Twitter: https://twitter.com/ovirt
* Check out the latest project news on the oVirt blog:
http://www.ovirt.org/blog/
[1] http://www.ovirt.org/release/4.4.0/
[2] http://resources.ovirt.org/pub/ovirt-4.4/iso/
--
Sandro Bonazzola
MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV
Red Hat EMEA <https://www.redhat.com/>
sbonazzo(a)redhat.com
<https://www.redhat.com/>
[image: |Our code is open_] <https://www.redhat.com/en/our-code-is-open>
*Red Hat respects your work life balance. Therefore there is no need to
answer this email out of your office hours.*
4 years, 8 months
It is possible to export a vm bigger as 5 TB?
by miguel.garcia＠toshibagcs.com
We have a vm with many virtual drives and need to backup as ova file. Since this demands a lot of space I had mounted an nfs directory in the host but get next message after try to export ova:
Error whle executing action: Cannot export VM. Invalid target folder: /mnt/shared2 on Host. You may refer to the engine.log file for further details.
Looking at the engine.log file got this mesage:
2020-07-03 11:42:37,268-04 INFO [org.ovirt.engine.core.bll.exportimport.ExportVmToOvaCommand] (default task-1929) [e357a397-3dc3-4566-900f-6e0e0cb39030] Lock Acquired to object 'EngineLock:{exclusiveLocks='[0b65c67d-98ae-435a-9c0a-2d9f0856a98b=VM]', sharedLocks=''}'
2020-07-03 11:42:37,275-04 INFO [org.ovirt.engine.core.common.utils.ansible.AnsibleExecutor] (default task-1929) [e357a397-3dc3-4566-900f-6e0e0cb39030] Executing Ansible command: /usr/bin/ansible-playbook --ssh-common-args=-F /var/lib/ovirt-engine/.ssh/config -v --private-key=/etc/pki/ovirt-engine/keys/engine_id_rsa --inventory=/tmp/ansible-inventory2275650137225503626 --extra-vars=target_directory="/nt/shared2" --extra-vars=validate_only="True" /usr/share/ovirt-engine/playbooks/ovirt-ova-export.yml [Logfile: /var/log/ovirt-engine/ova/ovirt-export-ova-validate-ansible-20200703114237-172.16.99.13-e357a397-3dc3-4566-900f-6e0e0cb39030.log]
2020-07-03 11:42:39,554-04 INFO [org.ovirt.engine.core.common.utils.ansible.AnsibleExecutor] (default task-1929) [e357a397-3dc3-4566-900f-6e0e0cb39030] Ansible playbook command has exited with value: 2
2020-07-03 11:42:39,555-04 WARN [org.ovirt.engine.core.bll.exportimport.ExportVmToOvaCommand] (default task-1929) [e357a397-3dc3-4566-900f-6e0e0cb39030] Validation of action 'ExportVmToOva' failed for user Miguel.Garcia. Reasons: VAR__ACTION__EXPORT,VAR__TYPE__VM,ACTION_TYPE_FAILED_INVALID_OVA_DESTINATION_FOLDER,$vdsName hyp11.infra,$directory /nt/shared2
2020-07-03 11:42:39,556-04 INFO [org.ovirt.engine.core.bll.exportimport.ExportVmToOvaCommand] (default task-1929) [e357a397-3dc3-4566-900f-6e0e0cb39030] Lock freed to object 'EngineLock:{exclusiveLocks='[0b65c67d-98ae-435a-9c0a-2d9f0856a98b=VM]', sharedLocks=''}'
2020-07-03 11:44:53,021-04 INFO [org.ovirt.engine.core.bll.exportimport.ExportVmToOvaCommand] (default task-1937) [ba070d4b-5f76-4fd7-adc0-53e0f96e6635] Lock Acquired to object 'EngineLock:{exclusiveLocks='[0b65c67d-98ae-435a-9c0a-2d9f0856a98b=VM]', sharedLocks=''}'
2020-07-03 11:44:53,027-04 INFO [org.ovirt.engine.core.common.utils.ansible.AnsibleExecutor] (default task-1937) [ba070d4b-5f76-4fd7-adc0-53e0f96e6635] Executing Ansible command: /usr/bin/ansible-playbook --ssh-common-args=-F /var/lib/ovirt-engine/.ssh/config -v --private-key=/etc/pki/ovirt-engine/keys/engine_id_rsa --inventory=/tmp/ansible-inventory3629946116235444875 --extra-vars=target_directory="/mnt/shared2" --extra-vars=validate_only="True" /usr/share/ovirt-engine/playbooks/ovirt-ova-export.yml [Logfile: /var/log/ovirt-engine/ova/ovirt-export-ova-validate-ansible-20200703114453-172.16.99.13-ba070d4b-5f76-4fd7-adc0-53e0f96e6635.log]
2020-07-03 11:44:55,538-04 INFO [org.ovirt.engine.core.common.utils.ansible.AnsibleExecutor] (default task-1937) [ba070d4b-5f76-4fd7-adc0-53e0f96e6635] Ansible playbook command has exited with value: 2
2020-07-03 11:44:55,538-04 WARN [org.ovirt.engine.core.bll.exportimport.ExportVmToOvaCommand] (default task-1937) [ba070d4b-5f76-4fd7-adc0-53e0f96e6635] Validation of action 'ExportVmToOva' failed for user Miguel.Garcia. Reasons: VAR__ACTION__EXPORT,VAR__TYPE__VM,ACTION_TYPE_FAILED_INVALID_OVA_DESTINATION_FOLDER,$vdsName hyp11.infra,$directory /mnt/shared2
2020-07-03 11:44:55,539-04 INFO [org.ovirt.engine.core.bll.exportimport.ExportVmToOvaCommand] (default task-1937) [ba070d4b-5f76-4fd7-adc0-53e0f96e6635] Lock freed to object 'EngineLock:{exclusiveLocks='[0b65c67d-98ae-435a-9c0a-2d9f0856a98b=VM]', sharedLocks=''}'
2020-07-03 11:45:17,391-04 INFO [org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-11) [6d510f0c] Lock Acquired to object 'EngineLock:{exclusiveLocks='[f762fb4b-57c1-40d0-bf3f-be4c83f16f44=PROVIDER]', sharedLocks=''}'
I had tried to addthe nfs partition as a Storage Domain data type but that didn't help either.
The mount persmission is as follow:
drwxr-xr-x. 3 vdsm kvm 50 Jul 3 11:47 /mnt/shared2
Any idea how can export this vm?
4 years, 8 months
OVA export creates empty and unusable images
by thomas＠hoberg.net
I've tested this now in three distinct farms with CentOS7.8 and the latest oVirt 4.3 release: OVA export files only contain an XML header and then lots of zeros where the disk images should be.
Where an 'ls -l <vmname>.ova' shows a file about the size of the disk, 'du -h <vmname>.ova' shows mere kilobytes, 'strings <vmname>.ova' dumps the XML and then nothing but repeating zeros until the end of the file.
Exporting existing VMs from a CentOS/RHEL 7 farm and importing them after a rebuild on CentOS/RHEL 8 would seem like a safe migration strategy, except when OVA export isn't working.
Please treat with priority!
4 years, 8 months
4.4 HCI Install Failure - Missing /etc/pki/CA/cacert.pem
by Stephen Panicho
Hi all! I'm using Cockpit to perform an HCI install, and it fails at the
hosted engine deploy. Libvirtd can't restart because of a missing
/etc/pki/CA/cacert.pem file.
The log (tasks seemingly from
/usr/share/ansible/roles/ovirt.hosted_engine_setup/tasks/initial_clean.yml):
[ INFO ] TASK [ovirt.hosted_engine_setup : Stop libvirt service]
[ INFO ] changed: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Drop vdsm config statements]
[ INFO ] changed: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Restore initial abrt config
files]
[ INFO ] changed: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Restart abrtd service]
[ INFO ] changed: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Drop libvirt sasl2 configuration
by vdsm]
[ INFO ] changed: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Stop and disable services]
[ INFO ] ok: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Restore initial libvirt default
network configuration]
[ INFO ] changed: [localhost]
[ INFO ] TASK [ovirt.hosted_engine_setup : Start libvirt]
[ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "Unable
to start service libvirtd: Job for libvirtd.service failed because the
control process exited with error code.\nSee \"systemctl status
libvirtd.service\" and \"journalctl -xe\" for details.\n"}
journalctl -u libvirtd:
May 22 04:33:25 node1 libvirtd[26392]: libvirt version: 5.6.0, package:
10.el8 (CBS <cbs(a)centos.org>, 2020-02-27-01:09:46, )
May 22 04:33:25 node1 libvirtd[26392]: hostname: node1
May 22 04:33:25 node1 libvirtd[26392]: Cannot read CA certificate
'/etc/pki/CA/cacert.pem': No such file or directory
May 22 04:33:25 node1 systemd[1]: libvirtd.service: Main process exited,
code=exited, status=6/NOTCONFIGURED
May 22 04:33:25 node1 systemd[1]: libvirtd.service: Failed with result
'exit-code'.
May 22 04:33:25 node1 systemd[1]: Failed to start Virtualization daemon.
From a fresh CentOS 8.1 minimal install, I've installed the following:
- The 4.4 repo
- cockpit
- ovirt-cockpit-dashboard
- vdsm-gluster (providing glusterfs-server and allowing the Gluster Wizard
to complete)
- gluster-ansible-roles (only on the bootstrap host)
I'm not exactly sure what that initial bit of the playbook does. Comparing
the bootstrap node with another that has yet to be touched, both
/etc/libvirt/libvirtd.conf and /etc/sysconfig/libvirtd are the same on both
hosts. Yet the bootstrap host can no longer start libvirtd while the other
host can. Neither host has the /etc/pki/CA/cacert.pem file.
Please let me know if I can provide any more information. Thanks!
4 years, 8 months
Deploy host engine error: The task includes an option with an undefined variable
by Angel R. Gonzalez
Hi all!
I'm deploying a host engine in a host node with a 8x Intel(R) Xeon(R)
CPU E5410 @ 2.33GHz.
The deploy proccess show the next message
> [INFO]TASK [ovirt.hosted_engine_setup : Convert CPU model name]
> [ERROR]fatal: [localhost]: FAILED! => {"msg": "The task includes an
> option with an undefined variable. The error was: 'dict object' has no
> attribute ''\n\nThe error appears to be in
> '/usr/share/ansible/roles/ovirt.hosted_engine_setup/tasks/create_target_vm/01_create_target_hosted_engine_vm.yml':
> line 105, column 15, but may\nbe elsewhere in the file depending on
> the exact syntax problem.\n\nThe offending line appears to be:\n\n -
> debug: var=server_cpu_dict\n ^ here\n\nThere appears to be both 'k=v'
> shorthand syntax and YAML in this task. Only one syntax may be used.\n"}
The ansible deploy script in his 105 line show:
> - name: Parse server CPU list
> set_fact:
> server_cpu_dict: "{{ server_cpu_dict |
> combine({item.split(':')[1]: item.split(':')[3]}) }}"
> with_items: >-
> {{
> server_cpu_list.json['values']['system_option_value'][0]['value'].split(';
> ')|list|difference(['']) }}
> - debug: var=server_cpu_dict
I don´t know ansible and i don't how to resolve this issue. Any idea?
Thanks in advance,
Ángel González.
4 years, 8 months
