Re: [ovirt-users] MacPoolRanges not working as expected

----- Original Message ----- > From: "Xavier Naveira" <xnaveira(a)gmail.com&gt; > To: users(a)ovirt.org > Sent: Monday, October 27, 2014 10:42:47 AM > Subject: [ovirt-users] MacPoolRanges not working as expected > > Hi everyone, > > First of all I'd like to say that we have been using oVirt successfully > for more than a year, creating an automated deploy system with help of > foreman and puppet. > > That being said, we're currently facing the first serious problem and > we'd appreciate some help. > > Everything was working fine until we exhausted the default > MacPoolRanges. After looking for a solution to the error message we > found this document: > http://www.ovirt.org/Engine_config_examples#MacPoolRanges > > Following the instructions on it we executed the following commands: > > First we found out what our current pool was: > > # engine-config -g MacPoolRanges > MacPoolRanges: 00:1a:4a:24:26:00-00:1a:4a:24:26:ff version: general > > So we proceeded to expand it: > > # engine-config -s "MacPoolRanges=00:1a:4a:24:26:00-00:1a:4a:24:27:ff" > # service ovirt-engine restart > > After this we were able to create new machines but none of them seemed > to have network. > > After some unsuccessful troubleshooting we restored the original pool > and instead added a new one: > > # engine-config -s "MacPoolRanges=00:1a:4a:24:26:00-00:1a:4a:24:26:ff" > # service ovirt-engine restart > > # engine-config -s > "MacPoolRanges=00:1a:4a:24:26:00-00:1a:4a:24:26:ff,00:1a:4a:24:27:00-00:1a:4a:24:27:ff" > > # service ovirt-engine restart > > After doing this and test to create a new host everything seemed to work > fine. > > The problem is that after the successful creation of some hosts the > original problem where the new hosts didn't seem to have network, > reappeared. > > Trying to narrow down the problem what we've find out so far is: > > This oVirt environment kickstarts hosts via PXE, when trying to PXE boot > a new host, the DHCP process fails (timeout). > > Tracing the network packets, we are able to see that the virtual host > sends the dhcp request, the dhcp server receives it and acknowledges it > and it sends the dhcp offer back. The dhcp offer reaches the hypervisor > to the vnetxx network interface BUT it doesn't go further and it doesn't > reach the virtual host. This behavior is consistent through different > hypervisors and vlans, including the ones that have been used/created > before the problems appeared. > > The only pattern that we've been able to identify so far is through > issuing the command "brctl showmacs <bridge_name>" > > This command list the mac addresses for the interfaces connected to the > bridge. In the cases where everything works fine the output looks like this: > > port no mac addr is local? ageing timer > 2 00:1a:4a:24:27:e0 no 0.01 > 2 fe:1a:4a:24:27:e0 yes 0.00 > > The virtual host MAC address begins with "00" and it has a corresponding > address beginning with "fe" which is assigned to the "vnetxx" interface > in the hypervisor. > > In the cases where the virtual host doesn't get the dhcp answers the > output of "brctl showmacs <bridge_name>" is: > > port no mac addr is local? ageing timer > 6 fe:1a:4a:24:27:a0 yes 0.00 > It seems that the vm has no vnic connected to the destined bridge. Which is weird due to the fact that you've noticed outgoing traffic from the vm to the DHCP server. Could you verify it by dumping the xml used to create the vm ? (could be obtained either from /var/log/vdsm/vdsm.log or by "virsh -r dumpxml <domain_id>" and the domain id could be obtained by "virsh -r list" or "vdsClient -s 0 list table" This will allow us to verify there is an actual interface device configured for that vm with the expected mac address and connected to the expect bridge. What is the nature of fe:1a:4a:24:27:a0 ? where did it come from ? Just to make sure - the expectation is for the virtual host to have a single interface only, with a mac address as allocated from the mac addresses pool. ovirt enables the nwfilter vdsm-no-mac-spoofing on libvirt to prevent spoofing of the assigned vnic mac address. But that should be confirmed. > This is, the actual virtual host's MAC address is missing from the bridge. > > We haven't been able to find a detailed explanation on how the network > internals of oVirt should work but hopefully someone in this list can > point us to the right resource. > > Thank you. > > Xavier. > > > > > > > > _______________________________________________ > Users mailing list > Users(a)ovirt.org > http://lists.ovirt.org/mailman/listinfo/users >