December 2019 - Users - Ovirt List Archives

[ovirt 4.2]vdsm host was shutdown unexpectly, configure of some vms was changed or lost when host was re-powered on and vm was started

by lifuqiong＠sunyainfo.com

Dear All: My ovirt engine managed two vdsms with nfs storage on another nfs server, it worked fine about three months. One of host (host_1.3; ip:172.18.1.3) was created about 16 vms, but the host_1.3 was shutdown unexpectly about 2019-12-23 16:11, when re-started host and vms; half of the vms was lost some configure or changed , such as lost theirs ip etc.(the vm name is 'zzh_Chain49_ACG_M' in the vdsm.log) the vm zzh_Chain49_ACG_M was create by rest API through vm's templated . the template is 20.1.1.161; the vm zzh_Chain49_ACG_M was created by ovirt rest api and changed the ip to 20.1.1.219 by ovirt rest api. But the ip was changed to templated ip when the accident happened. the vm's os is centos. Hope get help from you soon, Thank you. Mark Sincerely.

5 years

1
0
0 / 0

Re: Subscribe to mailing list and install oVirt with freeIPA

by Yedidyah Bar David

On Wed, Dec 25, 2019 at 10:45 AM Kien Pham <ptkcc(a)outlook.com> wrote: > > Dear oVirt team, > > I have post a thread on forum but I got problem with mailing list. How can I subscribe the mailing list. > > This is the question. > > Dear all, > > I am installing oVirt but I got an error when running engine-setup and get the following notification: > > [ INFO ] Restarting httpd > [ ERROR ] Failed to execute stage 'Closing up': Failed to start service 'httpd' > [ INFO ] Stage: Clean up > Log file is located at /var/log/ovirt-engine/setup/ovirt-engine-setup-20191224111455-ppsefr.log > [ INFO ] Generating answer file '/var/lib/ovirt-engine/setup/answers/20191224111745-setup.conf' > [ INFO ] Stage: Pre-termination > [ INFO ] Stage: Termination > [ ERROR ] Execution of setup failed > > I think that the problem is freeIPA. I installed freeIPA to manage user authetication. But IPA is currently using port 80 so httpd service cannot start. Right. This isn't supported, for exactly this reason. The ovirt-engine rpm conflicts with ipa-server. How did you install it? I now see that there is also a package python2-ipaserver, and in fedora and el8 also python3-ipaserver. Now pushed a patch to conflict with them as well: https://gerrit.ovirt.org/105935 Anyway, you'll have to set them up on two different machines. Thanks for the report, and sorry for the failure... Good luck and best regards, -- Didi

5 years

1
0
0 / 0

Re: oVirt and Containers

by Jan Zmeskal

Hi Robert, there are different answers based on what you mean by integrating oVirt and containers. Do you mean: - Installing container management (Kubernetes or OpenShift) on top of oVirt and using oVirt as infrastructure? - Managing containers from oVirt interface? - Running VM workloads inside containers? - Something different? I can elaborate more based on your specific needs Best regards Jan On Tue, Dec 24, 2019 at 3:52 PM Robert Webb <rwebb(a)ropeguru.com> wrote: > I was searching around to try and figure out the best way to integrate > oVirt and containers. > > > > I have found some sites that discuss it but all of them are like 2017 and > older. > > > > Any recommendations? > > > > Just build VM’s to host containers or is there some direct integration? > > > > Here are a couple of the old sites > > > > https://fromanirh.github.io/containers-in-ovirt.html > > > > > https://kubernetes.io/docs/setup/production-environment/on-premises-vm/ov... > > > > > https://www.ovirt.org/develop/release-management/features/integration/con... > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: > https://www.ovirt.org/community/about/community-guidelines/ > List Archives: > https://lists.ovirt.org/archives/list/users@ovirt.org/message/7BIW2Z3ILBS... > -- Jan Zmeskal Quality Engineer, RHV Core System Red Hat <https://www.redhat.com> <https://www.redhat.com>

5 years

2
1
0 / 0

Subscribe to mailing list and install oVirt with freeIPA

by Kien Pham

Dear oVirt team, I have post a thread on forum but I got problem with mailing list. How can I subscribe the mailing list. This is the question. Dear all, I am installing oVirt but I got an error when running engine-setup and get the following notification: [ INFO ] Restarting httpd [ ERROR ] Failed to execute stage 'Closing up': Failed to start service 'httpd' [ INFO ] Stage: Clean up Log file is located at /var/log/ovirt-engine/setup/ovirt-engine-setup-20191224111455-ppsefr.log [ INFO ] Generating answer file '/var/lib/ovirt-engine/setup/answers/20191224111745-setup.conf' [ INFO ] Stage: Pre-termination [ INFO ] Stage: Termination [ ERROR ] Execution of setup failed I think that the problem is freeIPA. I installed freeIPA to manage user authetication. But IPA is currently using port 80 so httpd service cannot start. Is there any suggest. Thank for all reply. Best regards. Kimloai.

5 years

1
0
0 / 0

Re: ovirt 4.3.7 + Gluster in hyperconverged (production design)

by Strahil

On Dec 24, 2019 02:18, Jayme <jaymef(a)gmail.com> wrote: > > If you can afford it I would definitely do raid. Being able to monitor and replace disks at the raid level is much easier than brick. With raid I’d do a gluster arbiter setup so your aren’t losing too much space. > > Keep an eye on libgfapi. It’s not default setting due to a few bugs but I’ve been testing it in my ssd hci cluster and have been seeing up to 5x io improvement. Also jumbo frames on those 10Gbps switches. > > Someone else will probably chime in re the other questions. I believe the GUI can only deploy a three sever cluster then you have to add the remaining hosts afterward. > > On Mon, Dec 23, 2019 at 5:56 PM <adrianquintero(a)gmail.com> wrote: >> >> Hi, >> After playing a bit with oVirt and Gluster in our pre-production environment for the last year, we have decided to move forward with a our production design using ovirt 4.3.7 + Gluster in a hyperconverged setup. >> >> For this we are looking get answers to a few questions that will help out with our design and eventually lead to our production deployment phase: >> >> Current HW specs (total servers = 18): >> 1.- Server type: DL380 GEN 9 >> 2.- Memory: 256GB >> 3.-Disk QTY per hypervisor: >> - 2x600GB SAS (RAID 0) for the OS I would pick Raid1 and split that between OS and brick for engine 's gluster volume >> - 9x1.2TB SSD (RAID[0, 6..]..? ) for GLUSTER. If you had bigger NICs I would preffer RAID0. Have you considered JBOD approach (each disk is presented as a standalone LUN from the raid array) ? Raid 6 is waste for your SSDs (when you already have replica 3 volumes). Ask HPE to provide SSDs from different manufacturing batches. I think that with SSD thee best compromise will be RAID 5 with replica3 for faster reads. As the SSDs will be overwritten with the same ammount of data, there could be a situation where all 3 from a replica set will be in predictive failiure (which is not nice) - that's why a raid 5 is a good option. >> 4.-Network: >> - Bond1: 2x10Gbps >> - Bond2: 2x10Gbps (for migration and gluster) Do not use Active-Backup bond as you will loose bandwidth. LACP (with hashing on layer 3+ layer4) is a good option, but it depends if your machines will be in the same LAN segment (communicating over layer 2 and no gateway inbetween). >> Our plan is to build 2x9 node clusters, however the following questions come up: >> >> 1.-Should we build 2 separate environments each with its own engine? or should we do 1 engine that will manage both clusters? If you decide to split - you have less fault tollerance - for example loosing 3 ot of 18 is better than loosing 3 out of 9 nodes :) >> 2.-What would be the best gluster volume layout for #1 above with regards to RAID configuration: >> - JBOD or RAID6 or…?. RAID6 wastes alot of space >> - what is the benefit or downside of using JBOD vs RAID 6 for this particular scenario? >> 3.-Would you recommend Ansible-based deployment (if supported)? If yes where would I find the documentation for it? or should we just deploy using the UI?. There is a topic in the mailing list about issues with ansible.It's up to you. >> - I have reviewed the following and in Chapter 5 it only mentions Web UI https://access.redhat.com/documentation/en-us/red_hat_hyperconverged_infr... >> - Also looked at https://github.com/gluster/gluster-ansible/tree/master/playbooks/hc-ansib... but could not get it to work properly. >> >> 4.-what is the recommended max server qty in a hyperconverged setup with gluster, 12, 15, 18...? I don't remmember but I think it was 9 nodes for Hyperconverged setup in RHV. >> Thanks, >> >> Adrian Best Regards, Strahil Nikolov

5 years

1
0
0 / 0

Re: Problems after 4.3.8 update

by Mahdi Adnan

We had an issue after upgrading Gluster nodes to 6.6, we had memory leak in gluster self heal daemon which cause it to do infinite heal and ate all of the nodes RAM "128GB", we had to downgrade to 6.5 to solve the problem. I think it is related to the changes made to the SHD code in version 6.6 ( 1760706 <https://bugzilla.redhat.com/1760706>) I might find the time and try to bug report the issue. Anyway, glad you solved your issue.

5 years

1
0
0 / 0

oVirt and Containers

by Robert Webb

I was searching around to try and figure out the best way to integrate oVirt and containers. I have found some sites that discuss it but all of them are like 2017 and older. Any recommendations? Just build VM's to host containers or is there some direct integration? Here are a couple of the old sites https://fromanirh.github.io/containers-in-ovirt.html https://kubernetes.io/docs/setup/production-environment/on-premises-vm/ov... https://www.ovirt.org/develop/release-management/features/integration/con...

5 years

1
0
0 / 0

Problems with ovirt-web-ui-1.6.0-1.el7.noarch

by Matthias Leopold

Hi, after upgrading oVirt from 4.3.5 to 4.3.7 some things in the VM Portal stopped working for users with "User" role: * running guest agent is not recognized ("It looks like no guest agent is configured on the VM.") * CD/ISO list is "[Empty]" for this I found "- limit CD/ISO list by data center" in rpm changelog, but this doesn't help me in any way Assigning other roles (UserVmRunTimeManager, PowerUserRole) doesn't change anything. /var/log/ovirt-engine/ui.log is quiet. Downgrading to ovirt-web-ui-1.5.3-1.el7.noarch resolves both issues. Am I the only one who is experiencing this? thx for advice Matthias

5 years

2
3
0 / 0

Re: Strategy to Mange Ovirt VMs Created from Templates

by Strahil

Sealing the VM is not something specific to oVirt, and is also valid for KVM. Actually sealing the VM is to run virt-sysprep against the VM/disk. You can check http://libguestfs.org/virt-sysprep.1.html and especially the --list-operations which can help you understand what ia being cleaned up. So you can: 1. Update the VM 2. Install and enable cloudinit service 3. Maybe try to create your ansible user and allow ssh keys (Using ansible over root is not good and is a bad practice) 4. Power off and seal the machine as a template (details at https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Virtuali... ) 5. Create VM from the template and power it up manually. 6. Verify that the new VM matches your needs and remove. About cloud init - you should know that is used extensively in OpenStack and VmWare has it's own solution similar to CloudInit. Some examples can be found at: https://cloudinit.readthedocs.io/en/latest/topics/examples.html So you can change passwords, configure network, create your ansible user with necessary permissions and way more. Best Regards, Strahil NikolovOn Dec 23, 2019 18:46, jeremy_tourville(a)hotmail.com wrote: > > Thank you for your reply Luca, > In general your work flow is helpful and makes sense to me. > > I meant to say above- "As part of the template creation process ***the Ovirt docs*** say to seal the VM". > > So I think I understand that you need to use both processes (seal template + cloudinit) to get everything to work as desired. I'd still appreciate any more specifics about what sealing a VM does. > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/BRLNWOQB6FM...

5 years

1
0
0 / 0

Strategy to Mange Ovirt VMs Created from Templates

by jeremy_tourville＠hotmail.com

I want to be able to manage VMs using Ansible. As part of the template creation process it says to seal the VM. Can someone tell me what sealing does to a Linux VM? I understand it removes some of things that make the VM unique but no real specifics. So, if I want to manage a VM created from a template would this general process work?- Seal the VM Install CloudInit and keys, accounts, etc Shut off VM and create template from it. Create new VM using Ansbile & CloudInit CloudInit would have just enough info so that you could manage the VM with Ansible. Would that work? I am just starting to explore what CloudInit can do and what it is. I am brand new to it. I didn't find enough info on template sealing to help me devise a full cycle management strategy. Perhaps there are other/easier methods? Thanks for your advice and input.

5 years

3
4
0 / 0

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

Users December 2019