July 2019 - Users - oVirt List Archives

Add Instance_type option for VM Portal
by Vrgotic, Marko 15 Jul '19

15 Jul '19

Dear oVIrt, We are relying on Templates more and more, which is great. Images/templates built using “official” cloud images usually have 1CPU and 1GB of RAM. Using this feature via Administration portal is super, since we can attach Instance_type to template to provide sufficient CPU and RAM, regardless of via UI or using Ansible. Would it be possible to consider adding Instance_Type option to Create New VM options in VM Portal? Haven’t tested yet, but is Instance_type supported via ovirt_vm ansible module, in case of EndUser privileges? Kindly awaiting your reply. — — — Met vriendelijke groet / Kind regards, Marko Vrgotic Sr. System Engineer @ System Administration m.vrgotic(a)activevideo.com<mailto:m.vrgotic@activevideo.com> tel. +31 (0)35 677 4131 ActiveVideo BV Mediacentrum 3741 Joop van den Endeplein 1 1217 WJ Hilversum

1 0

iptables with 4.3+?
by Jordan Conway 15 Jul '19

15 Jul '19

Hello, I'm working on migrating an existing ovirt setup to a new hosted-engine setup and I've been seeing messages about iptables support being deprecated and slated to be removed. Can I continue using iptables to manage the firewalls on my ovirt hosts if I don't care about allowing ovirt to configure the firewalls? We manage all of our machines with puppet and iptables is deeply integrated into this. It would be non-trivial to migrate to firewalld support. As it stands I already manage the firewall rules for our ovirt hosts with puppet and iptables and have always ignored the "Automatically Configure Firewall" option when adding new hosts. Will this continue to work? Also with hosted engine, I had to cowboy enable firewalld to get the engine installed, but now that I've got a cluster up and running with hosted engine enabled on several hosts, can I just switch back from firewalld to iptables assuming I've got all the correct ports open? Thank you, Jordan Conway

4 3

Re: ovirt-engine-appliance ova
by Strahil 14 Jul '19

14 Jul '19

Based on my experience - the OVA contains the xml and the actual disk of the hosted engine. Then the deployment starts locally the VM and populates the necessary data in it Once it's over , the deployment shuts down and copies the disk of that local VM, undefines it and then ovirt's ha agents are being configured - so they can mount the shared storage and power up the VM (special tar /OVMF/ file on shared storage has the agent configuration file). So , in the ova there should be a template VM + the xml config (cpus, ram, devices, etc) . I would be surprised if there is something else in it. Best Regards, Strahil NikolovOn Jul 11, 2019 23:39, Jingjie Jiang <jingjie.jiang(a)oracle.com> wrote: > > Hi Strahil, > > Yes, you are right. > > After install ovirt-engine-appliance rpm, the ova file will be save at /usr/share/ovirt-engine-appliance/ovirt-engine-appliance-4.3-20190610.1.el7.ova > > I was trying to understand what the ova file included. > > I thought it only has the CentOS7.6. > > I observed that ovirt-engine was installed during "host-engine --deploy" > > Is ovirt-engine-appliance-4.3-20190610.1.el7.ova only used for deploy host-engine? > > Is there a document about how to generate? > > > Thanks, > > Jingjie > > > On 7/11/19 4:20 PM, Strahil Nikolov wrote: > > If I'm not wrong, this rpm is being downloaded to one of the hosts during self-hosted engine's deployment. > Why would you try to import a second self-hosted engine ? > > Best Regards, > Strahil Nikolov > > > В четвъртък, 11 юли 2019 г., 22:37:56 ч. Гринуич+3, <jingjie.jiang(a)oracle.com> написа: > > > Hi, > Can someone tell me how to generate ovirt-engine-appliance ova file in ovirt-engine-appliance-4.3-20190610.1.el7.x86_64.rpm? > I tried to import ovirt-engine-appliance ova(ovirt-engine-appliance-4.3-20190610.1.el7.ova) from ovirt-engine, but I got error as following: > Failed to load VM configuration from OVA file: /var/tmp/ovirt-engine-appliance-4.2-20190121.1.el7.ova > > I guess ovirt-engine-appliance-4.2-20190121.1.el7.ova has more than CentOS7.6. > > Thanks, > Jingjie > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/EP2BMVXRXUM6F…" rel="nofollow" target="_blank" moz-do-not-send="true">https://lists.ovirt.org/archives/list/users@o

3 3

hosted engine installation on iscsi multipath/mpath device fails
by Michael Frank 14 Jul '19

14 Jul '19

Dear all, since several days i try to install the hosted engine initially to an iscsi multipath device without success. Some information on the environment: - Ovirt Version 4.3.3 - using two 10gbe interfaces as single lacp - bond for the ovirtmgmt interface - using two 10gbe storage interfaces on each hypervisor for iscsi storage -- each storage interface is configured without any lacp bonding or 802.1q tagging, etc (on the switches the vlan is configured; port based vlan) -- each storage interface lives in a serarate vlan were also the iscsi target is available, the iscsi target has 4x10ge interfaces -- so; each storage interface is connected to a iscsi target through a different vlan The documentation here is for me unclear: https://ovirt.org/documentation/self-hosted/chap-Deploying_Self-Hosted_Engi… <https://ovirt.org/documentation/self-hosted/chap-Deploying_Self-Hosted_Engi…> >Note: To specify more than one iSCSI target, you must enable multipathing before deploying the self-hosted engine. There is also a Multipath >Helper tool that generates a script to install and configure multipath with different options. This indicates for me that it should be possbile to install the HE directly on the /dev/mapper/mpath device which is availibale when I have prepared the host accordingly before installing the HE (log in to multiple iscsi targets, create proper multipath,conf, etc) - right ? I login to the two iscsi targets and get in sum 8 pathes, 4 from each interface and iscsi target. I have then the mpath device on the hypervisor available and i can mount the mpath device and put (test) data on it. In the cockpit interface the mount can also be activated and is recognized correctly. multipathd -ll and lsblk looks good. Everything seems to be fine. But when I run the "hosted-engine" --deploy, the last option while running the assistant is to enter the iscsi data. So, basically i just want to define my mpath device - when entering the data for one of my iscsi target I can see the 4 pathes of the single target, and when i choose the path where the "lun" is finally available it fails. I think in general this option is not that what i want to have here for using the multipath device. I' m lost - what is the usual way to install the HE on a mutlipath device ? Do I have to change the configuration of the storage interfaces or the iscsi network design? - Are bond interfaces for these iscsi connections mandatory ? Did I missed something obvious ? Can I put in my multipath data into the answerfile somehow to get rid of the last step of the assistant ? Is it not possible in general ?? : https://bugzilla.redhat.com/show_bug.cgi?id=1193961 <https://bugzilla.redhat.com/show_bug.cgi?id=1193961> Sorry in advance for the long mail .... 1!^^ br, michael

1 0

Re: System unable to recover after a crash
by Strahil 13 Jul '19

13 Jul '19

Hi Carl, I'd recommend you to avoid DNS & DHCP unless you oVirt infra consistes of hundreds of servers. It is far more reliable to use static IPs + /etc/hosts . As you could 'ssh' to the engine, check the logs - there should be a clue why it failed. Most probably it's related to the DNS/IP used. I think the devs can tell their opinion on Monday. Best Regards, Strahil NikolovOn Jul 13, 2019 15:08, carl langlois <crl.langlois(a)gmail.com> wrote: > > Hi > Thanks for the info. There have been some progress with the situation. So to make the story as short as possible we are in a process of changing our range of IP addresse to 10.8.X.X to 10.16.X.X for all of the ovirt infra. This implies a new DHCP server, new switchs etc etc. For now we went back to our old IP address ranges because we were not able to stabilize the system. > > So the last status using our new range of addresses was that gluster was all fine, the hosted engine domaine was moutning okey. I suspect DNS table was not properly updated.. but i am not 100% sure. But if we tried to used the new range of adrreses everything seems to be fine except that the hosted-engine always fail the "liveliness check" after going up. I was not able to solve this situation so i went back to our previous DHCP server. > > So i am not sure what is missing for the hosted-engine to use the DHCP server. Is there any hardcode config in the hosted-egnine that need to be updated when chaging DHCP server(i.e new address with the same hostname, new gateway..) > > More info on the test i did with the new DHCP server -- > All node have name resolution working. I am able to ssh to the hosted-engine > > Any suggestions will be appreciated as i am out of idea for now. Do i need to redo some sort of setup in the engine to take into account the range of address/new gateway? There is also a LDAP server access configure in the engine for username mapping.. > Carl > > > > > On Sat, Jul 13, 2019 at 6:31 AM Strahil Nikolov <hunter86_bg(a)yahoo.com> wrote: >> >> Can you mount the volume manually at another location ? >> Also, have you done any changes to Gluster ? >> >> Please provide "gluster volume info engine" . I have noticed the following in your logs: option 'parallel-readdir' is not recognized >> >> Best Regards, >> Strahil Nikolov >> >> В петък, 12 юли 2019 г., 22:30:41 ч. Гринуич+3, carl langlois <crl.langlois(a)gmail.com> написа: >> >> >> Hi , >> >> I am in state where my system does not recover from a major failure. I have pinpoint the probleme to be that the hosted engine storage domain is not able to mount >> >> I have a glusterfs containing the storage domain. but when it attempt to mount glusterfs to /rhev/data-center/mnt/glusterSD/ovhost1:_engine i get >> >> +------------------------------------------------------------------------------+ >> [2019-07-12 19:19:44.063608] I [rpc-clnt.c:1986:rpc_clnt_reconfig] 0-engine-client-2: changing port to 49153 (from 0) >> [2019-07-12 19:19:55.033725] I [fuse-bridge.c:4205:fuse_init] 0-glusterfs-fuse: FUSE inited with protocol versions: glusterfs 7.24 kernel 7.22 >> [2019-07-12 19:19:55.033748] I [fuse-bridge.c:4835:fuse_graph_sync] 0-fuse: switched to graph 0 >> [2019-07-12 19:19:55.033895] I [MSGID: 108006] [afr-common.c:537

1 0

Does Ovirt 4.3.4 have support for NFS 4/4.1/4.2 or pNFS
by Erick Perez 13 Jul '19

13 Jul '19

I have read the archives and the most recent discussion was 5 years ago. So I better ask again. My NAS runs Centos with NFS4.2 (and I am testing Ganesha in another server) Does Ovirt 4.3.4 have support for NFS 4/4.1/4.2 or pNFS Specially version 4.2 due to: Server-Side Copy: NFSv4.2 supports copy_file_range() system call, which allows the NFS client to efficiently copy data without wasting network resources. But this will only happen if the Ovirt (which I know is Centos based) supports NFS 4.2. Not sure If I update the NFS toolset on the Ovirt install, it will break something or worst.

3 2

System unable to recover after a crash
by carl langlois 13 Jul '19

13 Jul '19

Hi , I am in state where my system does not recover from a major failure. I have pinpoint the probleme to be that the hosted engine storage domain is not able to mount I have a glusterfs containing the storage domain. but when it attempt to mount glusterfs to /rhev/data-center/mnt/glusterSD/ovhost1:_engine i get +------------------------------------------------------------------------------+ [2019-07-12 19:19:44.063608] I [rpc-clnt.c:1986:rpc_clnt_reconfig] 0-engine-client-2: changing port to 49153 (from 0) [2019-07-12 19:19:55.033725] I [fuse-bridge.c:4205:fuse_init] 0-glusterfs-fuse: FUSE inited with protocol versions: glusterfs 7.24 kernel 7.22 [2019-07-12 19:19:55.033748] I [fuse-bridge.c:4835:fuse_graph_sync] 0-fuse: switched to graph 0 [2019-07-12 19:19:55.033895] I [MSGID: 108006] [afr-common.c:5372:afr_local_init] 0-engine-replicate-0: no subvolumes up [2019-07-12 19:19:55.033938] E [fuse-bridge.c:4271:fuse_first_lookup] 0-fuse: first lookup on root failed (Transport endpoint is not connected) [2019-07-12 19:19:55.034041] W [fuse-resolve.c:132:fuse_resolve_gfid_cbk] 0-fuse: 00000000-0000-0000-0000-000000000001: failed to resolve (Transport endpoint is not connected) [2019-07-12 19:19:55.034060] E [fuse-bridge.c:900:fuse_getattr_resume] 0-glusterfs-fuse: 2: GETATTR 1 (00000000-0000-0000-0000-000000000001) resolution failed [2019-07-12 19:19:55.034095] W [fuse-resolve.c:132:fuse_resolve_gfid_cbk] 0-fuse: 00000000-0000-0000-0000-000000000001: failed to resolve (Transport endpoint is not connected) [2019-07-12 19:19:55.034102] E [fuse-bridge.c:900:fuse_getattr_resume] 0-glusterfs-fuse: 3: GETATTR 1 (00000000-0000-0000-0000-000000000001) resolution failed [2019-07-12 19:19:55.035596] W [fuse-resolve.c:132:fuse_resolve_gfid_cbk] 0-fuse: 00000000-0000-0000-0000-000000000001: failed to resolve (Transport endpoint is not connected) [2019-07-12 19:19:55.035611] E [fuse-bridge.c:900:fuse_getattr_resume] 0-glusterfs-fuse: 4: GETATTR 1 (00000000-0000-0000-0000-000000000001) resolution failed [2019-07-12 19:19:55.047957] I [fuse-bridge.c:5093:fuse_thread_proc] 0-fuse: initating unmount of /rhev/data-center/mnt/glusterSD/ovhost1:_engine The message "I [MSGID: 108006] [afr-common.c:5372:afr_local_init] 0-engine-replicate-0: no subvolumes up" repeated 3 times between [2019-07-12 19:19:55.033895] and [2019-07-12 19:19:55.035588] [2019-07-12 19:19:55.048138] W [glusterfsd.c:1375:cleanup_and_exit] (-->/lib64/libpthread.so.0(+0x7e25) [0x7f51cecb3e25] -->/usr/sbin/glusterfs(glusterfs_sigwaiter+0xe5) [0x5632143bd4b5] -->/usr/sbin/glusterfs(cleanup_and_exit+0x6b) [0x5632143bd32b] ) 0-: received signum (15), shutting down [2019-07-12 19:19:55.048150] I [fuse-bridge.c:5852:fini] 0-fuse: Unmounting '/rhev/data-center/mnt/glusterSD/ovhost1:_engine'. [2019-07-12 19:19:55.048155] I [fuse-bridge.c:5857:fini] 0-fuse: Closing fuse connection to '/rhev/data-center/mnt/glusterSD/ovhost1:_engine'. [2019-07-12 19:19:56.029923] I [MSGID: 100030] [glusterfsd.c:2511:main] 0-/usr/sbin/glusterfs: Started running /usr/sbin/glusterfs version 3.12.11 (args: /usr/sbin/glusterfs --volfile-server=ovhost1 --volfile-server=ovhost2 --volfile-server=ovhost3 --volfile-id=/engine /rhev/data-center/mnt/glusterSD/ovhost1:_engine) [2019-07-12 19:19:56.032209] W [MSGID: 101002] [options.c:995:xl_opt_validate] 0-glusterfs: option 'address-family' is deprecated, preferred is 'transport.address-family', continuing with correction [2019-07-12 19:19:56.037510] I [MSGID: 101190] [event-epoll.c:613:event_dispatch_epoll_worker] 0-epoll: Started thread with index 1 [2019-07-12 19:19:56.039618] I [MSGID: 101190] [event-epoll.c:613:event_dispatch_epoll_worker] 0-epoll: Started thread with index 2 [2019-07-12 19:19:56.039691] W [MSGID: 101174] [graph.c:363:_log_if_unknown_option] 0-engine-readdir-ahead: option 'parallel-readdir' is not recognized [2019-07-12 19:19:56.039739] I [MSGID: 114020] [client.c:2360:notify] 0-engine-client-0: parent translators are ready, attempting connect on transport [2019-07-12 19:19:56.043324] I [MSGID: 114020] [client.c:2360:notify] 0-engine-client-1: parent translators are ready, attempting connect on transport [2019-07-12 19:19:56.043481] I [rpc-clnt.c:1986:rpc_clnt_reconfig] 0-engine-client-0: changing port to 49153 (from 0) [2019-07-12 19:19:56.048539] I [MSGID: 114020] [client.c:2360:notify] 0-engine-client-2: parent translators are ready, attempting connect on transport [2019-07-12 19:19:56.048952] I [rpc-clnt.c:1986:rpc_clnt_reconfig] 0-engine-client-1: changing port to 49153 (from 0) Final graph: without this mount point the ha-agent is not starting. the volume seem to be okey Gluster process TCP Port RDMA Port Online Pid ------------------------------------------------------------------------------ Brick ovhost1:/gluster_bricks/data/data 49152 0 Y 7505 Brick ovhost2:/gluster_bricks/data/data 49152 0 Y 3640 Brick ovhost3:/gluster_bricks/data/data 49152 0 Y 6329 Self-heal Daemon on localhost N/A N/A Y 7712 Self-heal Daemon on ovhost2 N/A N/A Y 4925 Self-heal Daemon on ovhost3 N/A N/A Y 6501 Task Status of Volume data ------------------------------------------------------------------------------ There are no active volume tasks Status of volume: engine Gluster process TCP Port RDMA Port Online Pid ------------------------------------------------------------------------------ Brick ovhost1:/gluster_bricks/engine/engine 49153 0 Y 7514 Brick ovhost2:/gluster_bricks/engine/engine 49153 0 Y 3662 Brick ovhost3:/gluster_bricks/engine/engine 49153 0 Y 6339 Self-heal Daemon on localhost N/A N/A Y 7712 Self-heal Daemon on ovhost2 N/A N/A Y 4925 Self-heal Daemon on ovhost3 N/A N/A Y 6501 Task Status of Volume engine ------------------------------------------------------------------------------ There are no active volume tasks Status of volume: iso Gluster process TCP Port RDMA Port Online Pid ------------------------------------------------------------------------------ Brick ovhost1:/gluster_bricks/iso/iso 49154 0 Y 7523 Brick ovhost2:/gluster_bricks/iso/iso 49154 0 Y 3715 Brick ovhost3:/gluster_bricks/iso/iso 49154 0 Y 6349 Self-heal Daemon on localhost N/A N/A Y 7712 Self-heal Daemon on ovhost2 N/A N/A Y 4925 Self-heal Daemon on ovhost3 N/A N/A Y 6501 Task Status of Volume iso ------------------------------------------------------------------------------ There are no active volume tasks Status of volume: vmstore Gluster process TCP Port RDMA Port Online Pid ------------------------------------------------------------------------------ Brick ovhost1:/gluster_bricks/vmstore/vmsto re 49155 0 Y 7532 Brick ovhost2:/gluster_bricks/vmstore/vmsto re 49155 0 Y 3739 Brick ovhost3:/gluster_bricks/vmstore/vmsto re 49155 0 Y 6359 Self-heal Daemon on localhost N/A N/A Y 7712 Self-heal Daemon on ovhost2 N/A N/A Y 4925 Self-heal Daemon on ovhost3 N/A N/A Y 6501 Task Status of Volume vmstore ------------------------------------------------------------------------------ There are no active volume tasks I am not sure what to look for at this point Any help would be really appreciated. Thanks Carl

3 3

"Actual timezone in guest doesn't match configuration" for Windows VMs since guest agent 4.3
by Matthias Leopold 12 Jul '19

12 Jul '19

Hi, the oVirt guest agent seems to report DST configuration for the timezone since version 4.3 (of the guest agent). this results in "Actual timezone in guest doesn't match configuration" messages in the UI for windows VMs because the timezone field can't be matched with oVirt configuration anymore (no DST flag). to me this looks like a bug. shall I report it? I know there was a similar thread at the beginning of May, but there was no solution mentioned. Matthias

2 3

An error has occurred during installation of Host
by lliujd＠gmail.com 11 Jul '19

11 Jul '19

Hello everyone, I have installed an 'oVirt Engine' by 'yum install ovirt-engine' and the engine runs fine after 'engine-setup'. But when I trying to add node host,some error occurred: 1st: An error has occurred during installation of Host node02: Yum Cannot queue package dmidecode: 'ascii' codec can't encode characters in position 143-147: ordinal not in range(128). 2ed: An error has occurred during installation of Host node02: Failed to execute stage 'Environment packages setup': 'ascii' codec can't encode characters in position 143-147: ordinal not in range(128). 3rd: Host node02 installation failed. Command returned failure code 1 during SSH session 'root@node02'. On host node02,package dmidecode has been installed: rpm -qa | grep dmidecode python-dmidecode-3.12.2-3.el7.x86_64 dmidecode-3.1-2.el7.x86_64 anyone can help ? Thanks !

2 2

Update 4.2.8 --> 4.3.5
by Christoph Köhler 11 Jul '19

11 Jul '19

Hello! We have a 4.2.8 environment with some managed gluster-volumes as storage domains and we want to go up to 4.3.5. How is that procedure especially with the gluster nodes in ovirt that are running 3.12.15? My fear is on the jump to gluster 6. Do the cluster work if the first node (of three) is upgraded? And what about the sequence - first the hypervisors or first gluster nodes? Is there anyone who had done this? Greetings! Christoph Köhler

1 0

Re: VM Migrations Failing
by Strahil 10 Jul '19

10 Jul '19

Power down the VM and reduce the memory a little bit but keep the maximum memory value the same or larger. Then power it up and extend the ram to the same value the VM had. It's a wild guess... So don't expect miracles. Best Regards, Strahil NikolovOn Jul 10, 2019 18:21, Michael Watters <wattersm(a)watters.ws> wrote: > > I need to migrate running VMs from one host in our cluster to another > however the task keeps failing any time I start a migration. The engine > logs show a few different errors as follows. > > 2019-07-10 09:53:19,440-04 ERROR > [org.ovirt.engine.core.vdsbroker.monitoring.VmAnalyzer] > (ForkJoinPool-1-worker-2) [] Migration of VM 'vm1' to host > 'ovirt-node-production3' failed: VM destroyed during the startup. > > 2019-07-10 09:53:06,542-04 ERROR > [org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLogDirector] > (default task-51) [c1daf639-ff39-4397-b1bf-09426cacf72d] EVENT_ID: > VM_MIGRATION_FAILED(65), Migration failed due to a failed validation: > [Cannot migrate VM. There is no host that satisfies current scheduling > constraints. See below for details:, The host ovirt-node-production3 did > not satisfy internal filter Memory.] (VM: vm2, Source: > ovirt-node-production2). > > I also checked the vdsm.log on the destination host which is showing an > error like this. > > ERROR (jsonrpc/2) [virt.vm] > (vmId='f5bb25a8-3176-40b6-b21b-f07ed1089b27') Alias not found for device > type balloon during migration at destination host (vm:5562) > > Does anybody know how to resolve this? The destination host is able to > run VMs and I've been able to move a few VMs by shutting down and doing > a restart however I'd like to do a live migration if possible. > > > > > > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/AWOTK2Q7OJGJX…

2 1

Manual Migration not working and Dashboard broken after 4.3.4 update
by Neil 10 Jul '19

10 Jul '19

Hi guys. I have two problems since upgrading from 4.2.x to 4.3.4 First issue is I can no longer manually migrate VM's between hosts, I get an error in the ovirt GUI that says "Could not fetch data needed for VM migrate operation" and nothing gets logged either in my engine.log or my vdsm.log Then the other issue is my Dashboard says the following "Error! Could not fetch dashboard data. Please ensure that data warehouse is properly installed and configured." If I look at my ovirt-engine-dwhd.log I see the following if I try restart the dwh service... 2019-07-09 11:48:04|ETL Service Started ovirtEngineDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbJdbcConnection|jdbc:postgresql://localhost:5432/ovirt_engine_history?sslfactory=org.postgresql.ssl.NonValidatingFactory hoursToKeepDaily|0 hoursToKeepHourly|720 ovirtEngineDbPassword|********************** runDeleteTime|3 ovirtEngineDbJdbcConnection|jdbc:postgresql://localhost:5432/engine?sslfactory=org.postgresql.ssl.NonValidatingFactory runInterleave|60 limitRows|limit 1000 ovirtEngineHistoryDbUser|ovirt_engine_history ovirtEngineDbUser|engine deleteIncrement|10 timeBetweenErrorEvents|300000 hoursToKeepSamples|24 deleteMultiplier|1000 lastErrorSent|2011-07-03 12:46:47.000000 etlVersion|4.3.0 dwhAggregationDebug|false dwhUuid|dca0ebd3-c58f-4389-a1f8-6aecc20b1316 ovirtEngineHistoryDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbPassword|********************** 2019-07-09 11:48:10|ETL Service Stopped 2019-07-09 11:49:59|ETL Service Started ovirtEngineDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbJdbcConnection|jdbc:postgresql://localhost:5432/ovirt_engine_history?sslfactory=org.postgresql.ssl.NonValidatingFactory hoursToKeepDaily|0 hoursToKeepHourly|720 ovirtEngineDbPassword|********************** runDeleteTime|3 ovirtEngineDbJdbcConnection|jdbc:postgresql://localhost:5432/engine?sslfactory=org.postgresql.ssl.NonValidatingFactory runInterleave|60 limitRows|limit 1000 ovirtEngineHistoryDbUser|ovirt_engine_history ovirtEngineDbUser|engine deleteIncrement|10 timeBetweenErrorEvents|300000 hoursToKeepSamples|24 deleteMultiplier|1000 lastErrorSent|2011-07-03 12:46:47.000000 etlVersion|4.3.0 dwhAggregationDebug|false dwhUuid|dca0ebd3-c58f-4389-a1f8-6aecc20b1316 ovirtEngineHistoryDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbPassword|********************** 2019-07-09 11:52:56|ETL Service Stopped 2019-07-09 11:52:57|ETL Service Started ovirtEngineDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbJdbcConnection|jdbc:postgresql://localhost:5432/ovirt_engine_history?sslfactory=org.postgresql.ssl.NonValidatingFactory hoursToKeepDaily|0 hoursToKeepHourly|720 ovirtEngineDbPassword|********************** runDeleteTime|3 ovirtEngineDbJdbcConnection|jdbc:postgresql://localhost:5432/engine?sslfactory=org.postgresql.ssl.NonValidatingFactory runInterleave|60 limitRows|limit 1000 ovirtEngineHistoryDbUser|ovirt_engine_history ovirtEngineDbUser|engine deleteIncrement|10 timeBetweenErrorEvents|300000 hoursToKeepSamples|24 deleteMultiplier|1000 lastErrorSent|2011-07-03 12:46:47.000000 etlVersion|4.3.0 dwhAggregationDebug|false dwhUuid|dca0ebd3-c58f-4389-a1f8-6aecc20b1316 ovirtEngineHistoryDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbPassword|********************** 2019-07-09 12:16:01|ETL Service Stopped 2019-07-09 12:16:45|ETL Service Started ovirtEngineDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbJdbcConnection|jdbc:postgresql://localhost:5432/ovirt_engine_history?sslfactory=org.postgresql.ssl.NonValidatingFactory hoursToKeepDaily|0 hoursToKeepHourly|720 ovirtEngineDbPassword|********************** runDeleteTime|3 ovirtEngineDbJdbcConnection|jdbc:postgresql://localhost:5432/engine?sslfactory=org.postgresql.ssl.NonValidatingFactory runInterleave|60 limitRows|limit 1000 ovirtEngineHistoryDbUser|ovirt_engine_history ovirtEngineDbUser|engine deleteIncrement|10 timeBetweenErrorEvents|300000 hoursToKeepSamples|24 deleteMultiplier|1000 lastErrorSent|2011-07-03 12:46:47.000000 etlVersion|4.3.0 dwhAggregationDebug|false dwhUuid|dca0ebd3-c58f-4389-a1f8-6aecc20b1316 ovirtEngineHistoryDbDriverClass|org.postgresql.Driver ovirtEngineHistoryDbPassword|********************** I have a hosted engine, and I have two hosts and my storage is FC based. The hosts are still running on 4.2 because I'm unable to migrate VM's off. I have plenty resources available in terms of CPU and Memory on the destination host, and my Cluster version is set to 4.2 because my hosts are still on 4.2 I have recently upgraded from 4.1 to 4.2 and then I upgraded my hosts to 4.2 as well, but I can't get my hosts to 4.3 because of the above migration issue. Below my ovirt packages installed... ovirt-ansible-cluster-upgrade-1.1.13-1.el7.noarch ovirt-ansible-disaster-recovery-1.1.4-1.el7.noarch ovirt-ansible-engine-setup-1.1.9-1.el7.noarch ovirt-ansible-hosted-engine-setup-1.0.20-1.el7.noarch ovirt-ansible-image-template-1.1.11-1.el7.noarch ovirt-ansible-infra-1.1.12-1.el7.noarch ovirt-ansible-manageiq-1.1.14-1.el7.noarch ovirt-ansible-repositories-1.1.5-1.el7.noarch ovirt-ansible-roles-1.1.6-1.el7.noarch ovirt-ansible-shutdown-env-1.0.3-1.el7.noarch ovirt-ansible-vm-infra-1.1.18-1.el7.noarch ovirt-cockpit-sso-0.1.1-1.el7.noarch ovirt-engine-4.3.4.3-1.el7.noarch ovirt-engine-api-explorer-0.0.5-1.el7.noarch ovirt-engine-backend-4.3.4.3-1.el7.noarch ovirt-engine-cli-3.6.9.2-1.el7.centos.noarch ovirt-engine-dbscripts-4.3.4.3-1.el7.noarch ovirt-engine-dwh-4.3.0-1.el7.noarch ovirt-engine-dwh-setup-4.3.0-1.el7.noarch ovirt-engine-extension-aaa-jdbc-1.1.10-1.el7.noarch ovirt-engine-extensions-api-impl-4.3.4.3-1.el7.noarch ovirt-engine-metrics-1.3.3.1-1.el7.noarch ovirt-engine-restapi-4.3.4.3-1.el7.noarch ovirt-engine-sdk-python-3.6.9.1-1.el7.centos.noarch ovirt-engine-setup-4.3.4.3-1.el7.noarch ovirt-engine-setup-base-4.3.4.3-1.el7.noarch ovirt-engine-setup-plugin-cinderlib-4.3.4.3-1.el7.noarch ovirt-engine-setup-plugin-ovirt-engine-4.3.4.3-1.el7.noarch ovirt-engine-setup-plugin-ovirt-engine-common-4.3.4.3-1.el7.noarch ovirt-engine-setup-plugin-vmconsole-proxy-helper-4.3.4.3-1.el7.noarch ovirt-engine-setup-plugin-websocket-proxy-4.3.4.3-1.el7.noarch ovirt-engine-tools-4.3.4.3-1.el7.noarch ovirt-engine-tools-backup-4.3.4.3-1.el7.noarch ovirt-engine-ui-extensions-1.0.5-1.el7.noarch ovirt-engine-vmconsole-proxy-helper-4.3.4.3-1.el7.noarch ovirt-engine-webadmin-portal-4.3.4.3-1.el7.noarch ovirt-engine-websocket-proxy-4.3.4.3-1.el7.noarch ovirt-engine-wildfly-15.0.1-1.el7.x86_64 ovirt-engine-wildfly-overlay-15.0.1-1.el7.noarch ovirt-guest-agent-common-1.0.16-1.el7.noarch ovirt-guest-tools-iso-4.3-3.el7.noarch ovirt-host-deploy-common-1.8.0-1.el7.noarch ovirt-host-deploy-java-1.8.0-1.el7.noarch ovirt-imageio-common-1.5.1-0.el7.x86_64 ovirt-imageio-proxy-1.5.1-0.el7.noarch ovirt-imageio-proxy-setup-1.5.1-0.el7.noarch ovirt-iso-uploader-4.3.1-1.el7.noarch ovirt-js-dependencies-1.2.0-3.1.el7.centos.noarch ovirt-provider-ovn-1.2.22-1.el7.noarch ovirt-release41-4.1.9-1.el7.centos.noarch ovirt-release42-4.2.8-1.el7.noarch ovirt-release43-4.3.4-1.el7.noarch ovirt-vmconsole-1.0.7-2.el7.noarch ovirt-vmconsole-proxy-1.0.7-2.el7.noarch ovirt-web-ui-1.5.2-1.el7.noarch python2-ovirt-engine-lib-4.3.4.3-1.el7.noarch python2-ovirt-host-deploy-1.8.0-1.el7.noarch python2-ovirt-setup-lib-1.2.0-1.el7.noarch python-ovirt-engine-sdk4-4.3.1-2.el7.x86_64 [root@dell-ovirt ~]# rpm -qa | grep postgre rh-postgresql10-postgresql-contrib-10.6-1.el7.x86_64 rh-postgresql10-postgresql-10.6-1.el7.x86_64 postgresql-libs-9.2.24-1.el7_5.x86_64 collectd-postgresql-5.8.1-4.el7.x86_64 postgresql-server-9.2.24-1.el7_5.x86_64 rh-postgresql10-postgresql-server-10.6-1.el7.x86_64 rh-postgresql95-postgresql-9.5.14-1.el7.x86_64 rh-postgresql95-postgresql-contrib-9.5.14-1.el7.x86_64 postgresql-jdbc-9.2.1002-6.el7_5.noarch rh-postgresql10-runtime-3.1-1.el7.x86_64 rh-postgresql95-postgresql-libs-9.5.14-1.el7.x86_64 rh-postgresql10-postgresql-libs-10.6-1.el7.x86_64 postgresql-9.2.24-1.el7_5.x86_64 rh-postgresql95-runtime-2.2-2.el7.x86_64 rh-postgresql95-postgresql-server-9.5.14-1.el7.x86_64 I'm also seeing a strange error on my hosts when I log in showing... node status: DEGRADED Please check the status manually using `nodectl check` [root@host-a ~]# nodectl check Status: FAILED Bootloader ... OK Layer boot entries ... OK Valid boot entries ... OK Mount points ... OK Separate /var ... OK Discard is used ... OK Basic storage ... OK Initialized VG ... OK Initialized Thin Pool ... OK Initialized LVs ... OK Thin storage ... FAILED - It looks like the LVM layout is not correct. The reason could be an incorrect installation. Checking available space in thinpool ... OK Checking thinpool auto-extend ... FAILED - In order to enable thinpool auto-extend,activation/thin_pool_autoextend_threshold needs to be set below 100 in lvm.conf vdsmd ... OK I'm running CentOS Linux release 7.6.1810 (Core) These are my package versions on my hosts... [root@host-a ~]# rpm -qa | grep -i ovirt ovirt-release41-4.1.9-1.el7.centos.noarch ovirt-hosted-engine-ha-2.2.19-1.el7.noarch ovirt-host-deploy-1.7.4-1.el7.noarch ovirt-node-ng-nodectl-4.2.0-0.20190121.0.el7.noarch ovirt-vmconsole-host-1.0.6-2.el7.noarch ovirt-provider-ovn-driver-1.2.18-1.el7.noarch ovirt-engine-appliance-4.2-20190121.1.el7.noarch ovirt-release42-4.2.8-1.el7.noarch ovirt-release43-4.3.4-1.el7.noarch python-ovirt-engine-sdk4-4.2.9-2.el7.x86_64 cockpit-ovirt-dashboard-0.11.38-1.el7.noarch ovirt-imageio-daemon-1.4.6-1.el7.noarch ovirt-host-4.2.3-1.el7.x86_64 ovirt-setup-lib-1.1.5-1.el7.noarch ovirt-node-ng-image-update-4.2.8-1.el7.noarch ovirt-imageio-common-1.4.6-1.el7.x86_64 ovirt-vmconsole-1.0.6-2.el7.noarch ovirt-engine-sdk-python-3.6.9.1-1.el7.centos.noarch ovirt-host-dependencies-4.2.3-1.el7.x86_64 ovirt-release-host-node-4.2.8-1.el7.noarch cockpit-machines-ovirt-193-2.el7.noarch ovirt-hosted-engine-setup-2.2.33-1.el7.noarch [root@host-a ~]# rpm -qa | grep -i vdsm vdsm-http-4.20.46-1.el7.noarch vdsm-common-4.20.46-1.el7.noarch vdsm-network-4.20.46-1.el7.x86_64 vdsm-jsonrpc-4.20.46-1.el7.noarch vdsm-4.20.46-1.el7.x86_64 vdsm-hook-ethtool-options-4.20.46-1.el7.noarch vdsm-hook-vhostmd-4.20.46-1.el7.noarch vdsm-python-4.20.46-1.el7.noarch vdsm-api-4.20.46-1.el7.noarch vdsm-yajsonrpc-4.20.46-1.el7.noarch vdsm-hook-fcoe-4.20.46-1.el7.noarch vdsm-hook-openstacknet-4.20.46-1.el7.noarch vdsm-client-4.20.46-1.el7.noarch vdsm-gluster-4.20.46-1.el7.x86_64 vdsm-hook-vmfex-dev-4.20.46-1.el7.noarch I am seeing the following error every minute or so in my vdsm.log as follows.... 2019-07-09 12:50:31,543+0200 WARN (qgapoller/2) [virt.periodic.VmDispatcher] could not run <function <lambda> at 0x7f52b01b85f0> on ['9a6561b8-5702-43dc-9e92-1dc5dfed4eef'] (periodic:323) Then also under /var/log/messages.. Jul 9 12:57:48 host-a ovs-vsctl: ovs|00001|db_ctl_base|ERR|unix:/var/run/openvswitch/db.sock: database connection failed (No such file or directory) I'm not using ovn so I'm guessing this can be ignored. If I search for ERROR or WARN in my logs nothing relevant is logged Any suggestions on what to start looking for please? Please let me know if you need further info. Thank you. Regards. Neil Wilson

4 9

Re: Impossible to install VM Machine
by Juan Pablo Lorier 10 Jul '19

10 Jul '19

Hi Abdoul, what I don't get right is what is your setup. Ovirt can have data domains that is where you put the vm disks. That domains can be NFS share, gluster bricks, iscsi san or direct disk. When you say files sharing folders, I can't think of a data domain attached there unless it's a NFS local share. Maybe I'm missing something, but I can see that working. Do you have a data domain in storage? I tend to think you have because otherway you can't create the disks for the vms (which you add when you create the vm) Please, replay to the list too so others can see the thread. Regards On 10/7/19 16:51, Abdoul-Rahamane Issoufou Oumarou wrote: > Thank you Juan Pablo, > > Yes indeed I installed everything on one machine. Before I used > ovirt-node and ovirt but it always gave me the same problem. > > I'm going to try again and I'll make you a catch of the mistakes I get. > > Otherwise for storage, I created FILES sharing folders on the ovirt > machine it's them that I use. > > Thank you very much > > Le mer. 10 juil. 2019 à 20:24, Juan Pablo Lorier <jplorier(a)gmail.com > <mailto:jplorier@gmail.com>> a écrit : > > Hi, > > We need more information to try and find the problem. Did you look at > the logs in ovirt-engine? I assume by your description that you ran an > all in one install. What storage are you using? > > Regards >

2 1

Impossible to install VM Machine
by Juan Pablo Lorier 10 Jul '19

10 Jul '19

Hi, We need more information to try and find the problem. Did you look at the logs in ovirt-engine? I assume by your description that you ran an all in one install. What storage are you using? Regards

1 0

Re: iptables with 4.3+?
by Strahil 10 Jul '19

10 Jul '19

Firewalld was deployed in EL7 , because they got plans of getting rid of iptables. With EL8 , we got only emulation of iptables for backward compatibility. Also the integration between NetworkManager.service and firewalld is quite good - which is another reason behind that. Last but not least, in the enterprise almost all systems are with firewalld down and behind hardware-based appliances and keeping the complex filtering away of the systems. Thus firewalld is nice for simple tasks, while complex tasks require nftables ... It makes sense and we have to deal with the changes or get extended support for as long as possible :) Best Regards, Strahil NikolovOn Jul 10, 2019 18:13, Michael Watters <wattersm(a)watters.ws> wrote: > > Same here. Our engine is configured to use iptables and works fine. I > really wish RedHat would stop trying to force firewalld on everything. > It isn't needed and causes issues with environments using the > puppetlabs-firewall module. > > On 7/4/19 3:17 PM, Darrell Budic wrote: > > I’m in the same boat, puppet managing iptables rules, and was able to continue forcing it on my 4.3.x ovirt systems. Engine-setup complains all the time, but so far it hasn’t broken anything. > > > > -Darrell > > > > > >> On Jul 4, 2019, at 9:38 AM, Jordan Conway <jconway(a)linuxfoundation.org> wrote: > >> > >> Hello, > >> I'm working on migrating an existing ovirt setup to a new hosted-engine setup and I've been seeing messages about iptables support being deprecated and slated to be removed. > >> Can I continue using iptables to manage the firewalls on my ovirt hosts if I don't care about allowing ovirt to configure the firewalls? > >> We manage all of our machines with puppet and iptables is deeply integrated into this. It would be non-trivial to migrate to firewalld support. > >> As it stands I already manage the firewall rules for our ovirt hosts with puppet and iptables and have always ignored the "Automatically Configure Firewall" option when adding new hosts. Will this continue to work? > >> > >> Also with hosted engine, I had to cowboy enable firewalld to get the engine installed, but now that I've got a cluster up and running with hosted engine enabled on several hosts, can I just switch back from firewalld to iptables assuming I've got all the correct ports open? > >> > >> Thank you, > >> Jordan Conway > >> _______________________________________________ > >> Users mailing list -- users(a)ovirt.org > >> To unsubscribe send an email to users-leave(a)ovirt.org > >> Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > >> oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > >> List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/CFKUWD44EKAOG… > > _______________________________________________ > > Users mailing list -- users(a)ovirt.org > > To unsubscribe send an email to users-leave(a)ovirt.org > > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/7HKXXY6KFVICS… > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/QBDHDHEC7FNQE…

1 0

VM Migrations Failing
by Michael Watters 10 Jul '19

10 Jul '19

I need to migrate running VMs from one host in our cluster to another however the task keeps failing any time I start a migration. The engine logs show a few different errors as follows. 2019-07-10 09:53:19,440-04 ERROR [org.ovirt.engine.core.vdsbroker.monitoring.VmAnalyzer] (ForkJoinPool-1-worker-2) [] Migration of VM 'vm1' to host 'ovirt-node-production3' failed: VM destroyed during the startup. 2019-07-10 09:53:06,542-04 ERROR [org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLogDirector] (default task-51) [c1daf639-ff39-4397-b1bf-09426cacf72d] EVENT_ID: VM_MIGRATION_FAILED(65), Migration failed due to a failed validation: [Cannot migrate VM. There is no host that satisfies current scheduling constraints. See below for details:, The host ovirt-node-production3 did not satisfy internal filter Memory.] (VM: vm2, Source: ovirt-node-production2). I also checked the vdsm.log on the destination host which is showing an error like this. ERROR (jsonrpc/2) [virt.vm] (vmId='f5bb25a8-3176-40b6-b21b-f07ed1089b27') Alias not found for device type balloon during migration at destination host (vm:5562) Does anybody know how to resolve this? The destination host is able to run VMs and I've been able to move a few VMs by shutting down and doing a restart however I'd like to do a live migration if possible.

1 0

ovirt_disk and ubuntu issues
by Vrgotic, Marko 10 Jul '19

10 Jul '19

Dear oVirt, I am downloading the ubuntu cloud image 16.04 and or 18.04: - name: "Download base cloud image from server" get_url: url: "{{ image_url }}" checksum: "sha256:{{ image_checksum }}" validate_certs: yes dest: "/tmp/{{ inventory_hostname_short }}.qcow2" delegate_to: localhost creating a 40GB HDD and attaching image to it: - name: "Create oVirt disk with base image (with 40Gb allocated)" ovirt_disk: name: "{{ inventory_hostname_short }}" interface: virtio size: 40GiB format: cow upload_image_path: "/tmp/{{ inventory_hostname_short }}.qcow2" storage_domain: ovirt_production wait: true delegate_to: localhost creating VM afterwards: - name: "Create new Ubuntu VMs from cloud image" delegate_to: localhost ovirt_vm: auth: "{{ ovirt_auth }}" name: "{{ inventory_hostname_short }}" disks: - name: "{{ inventory_hostname_short }}" graphical_console: protocol: vnc serial_console: true usb_support: true soundcard_enabled: false operating_system: "{{ operating_system_type }}" type: server nics: - name: nic1 profile_name: tenant1 interface: virtio nic_on_boot: true cloud_init: host_name: "{{ inventory_hostname }}" user_name: ubuntu authorized_ssh_keys: "{{ ssh_agent_pubkeys.stdout }}" state: "running" cluster: "{{ ovirt_cluster }}" when: inventory_hostname in groups['ubuntu-baker'] When VM gets created, I can see in oVIrt VM details disk created is 40GB. Executing df -h, gives me following: root@av3-ubuntu-18-base:/home/ubuntu# df -h Filesystem Size Used Avail Use% Mounted on udev 447M 0 447M 0% /dev tmpfs 92M 696K 92M 1% /run /dev/vda1 2.0G 1.3G 706M 65% / tmpfs 460M 0 460M 0% /dev/shm tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 460M 0 460M 0% /sys/fs/cgroup /dev/vda15 105M 3.6M 101M 4% /boot/efi tmpfs 92M 0 92M 0% /run/user/1000 Initially I thought growpart or resize2fs is not triggered, but then running dmesg or fdisk /dev/vda, told me that physical disk size is still only size of the downloaded ubuntu cloud image. Disk /dev/vda: 2.2 GiB, 2361393152 bytes, 4612096 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Is this related to ovirt_disk module, or ubuntu and ovirt_disk, since I do not have this behavior with CentOS 7 images? Can you advise how to proceed, in case I am missing some configuration parameter or command to be run? The following Ubuntu images are used: ubuntu-16: image_url=https://cloud-images.ubuntu.com/xenial/current/xenial-server-clou… image_checksum=fda868058586b129c7fdb6472fe575e911f7c67551a6dc75966f2ec02201bdae ubuntu-18: image_url=https://cloud-images.ubuntu.com/bionic/current/bionic-server-clou… image_checksum=7d2b90022a169119d7726c0fefa1713acbead7cc36d282c879896fd89c5a6663 Kindly awaiting your reply. — — — Met vriendelijke groet / Kind regards, Marko Vrgotic Sr. System Engineer @ System Administration m.vrgotic(a)activevideo.com<mailto:m.vrgotic@activevideo.com> tel. +31 (0)35 677 4131

1 0

Re: Help!
by Strahil 10 Jul '19

10 Jul '19

Edit the VM and go to 'system' tab (on the left). If you don't see it -click on 'show advanced options'. There select Harddisk as 1st device and DVD as second. Also mark the tick for the disk and from the dropdown choose your install disk. Then poweroff and then poweron. Best Regards, Strahil NikolovOn Jul 10, 2019 15:27, Abdoul-Rahamane Issoufou Oumarou <ioabdoulrahamaneapp.site(a)gmail.com> wrote: > > Good evening > > Today it's been almost a week since my efforts are in vain in the face of this problem that pushes me to write to you again. > > I installed ovirt 4.3 on a minimal centos installation. > Then I confided ovirt as well as the iso and data domains. > > Now the problem, I try to create a VM by setting up the entries and attaching a CD from the iso data center. > > As soon as I run the machine by opening the console, the VM blocks on the boot and the installation does not start. I'll give you two previews for my config and the problem in question. > > Thank you in advance to all those who would like to help me solve this problem.

1 0

Impossible to install VM Machine
by ioabdoulrahamaneapp.site＠gmail.com 10 Jul '19

10 Jul '19

Good evening Today it's been almost a week since my efforts are in vain in the face of this problem that pushes me to write to you again. I installed ovirt 4.3 on a minimal centos installation. Then I confided ovirt as well as the iso and data domains. Now the problem, I try to create a VM by setting up the entries and attaching a CD from the iso data center. As soon as I run the machine by opening the console, the VM blocks on the boot and the installation does not start. I'll give you two previews for my config and the problem in question. Thank you in advance to all those who would like to help me solve this problem. http://prntscr.com/od3ywo http://prntscr.com/od43v6

1 0

Help!
by Abdoul-Rahamane Issoufou Oumarou 10 Jul '19

10 Jul '19

Good evening Today it's been almost a week since my efforts are in vain in the face of this problem that pushes me to write to you again. I installed ovirt 4.3 on a minimal centos installation. Then I confided ovirt as well as the iso and data domains. Now the problem, I try to create a VM by setting up the entries and attaching a CD from the iso data center. As soon as I run the machine by opening the console, the VM blocks on the boot and the installation does not start. I'll give you two previews for my config and the problem in question. Thank you in advance to all those who would like to help me solve this problem.

1 0

Can't open console
by Ron Baduach -X (rbaduach - SQLINK LTD＠Cisco) 10 Jul '19

10 Jul '19

Hi, When trying to open a console for my VM , I'm getting this error : [cid:image001.png@01D53732.4E21AD20] Can you please help ? Thanks in advance [https://www.cisco.com/c/dam/m/en_us/signaturetool/images/logo/Cisco_Logo_no…] Ron Baduach Lab Staff rbaduach(a)cisco.com<mailto:rbaduach@cisco.com> Tel: +972 9 892 7004 Cisco Systems, Inc. 32 HaMelacha St., (HaSharon Bldg) P.O.Box 8735, I.Z.Sapir SOUTH NETANYA 42504 Israel cisco.com [http://www.cisco.com/assets/swa/img/thinkbeforeyouprint.gif] Think before you print. This email may contain confidential and privileged material for the sole use of the intended recipient. Any review, use, distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or authorized to receive for the recipient), please contact the sender by reply email and delete all copies of this message. Please click here<http://www.cisco.com/c/en/us/about/legal/terms-sale-software-license-agreem…> for Company Registration Information.

1 0

ISO Upload "Paused by System"
by Ron Baduach -X (rbaduach - SQLINK LTD＠Cisco) 10 Jul '19

10 Jul '19

Hi Guys, I tried to upload an ISO, and from "chrome" it's just "paused by system" from the beginning From "Firefox", it started to upload, but after 0.5 hour it becomes "paused by system" too. I suspect it's the certificate issue, but I installed the certificate. [I'm working with Windows 10] Can you please tell me it this is the issue ?and if yes, how can I solve the Cert issue ? I'm just stuck here, so thanks in advance ! [https://www.cisco.com/c/dam/m/en_us/signaturetool/images/logo/Cisco_Logo_no…] Ron Baduach Lab Staff rbaduach(a)cisco.com<mailto:rbaduach@cisco.com> Tel: +972 9 892 7004 Cisco Systems, Inc. 32 HaMelacha St., (HaSharon Bldg) P.O.Box 8735, I.Z.Sapir SOUTH NETANYA 42504 Israel cisco.com [http://www.cisco.com/assets/swa/img/thinkbeforeyouprint.gif] Think before you print. This email may contain confidential and privileged material for the sole use of the intended recipient. Any review, use, distribution or disclosure by others is strictly prohibited. If you are not the intended recipient (or authorized to receive for the recipient), please contact the sender by reply email and delete all copies of this message. Please click here<http://www.cisco.com/c/en/us/about/legal/terms-sale-software-license-agreem…> for Company Registration Information.

2 2

UI exception when changing Cluster in New VM window
by Vrgotic, Marko 10 Jul '19

10 Jul '19

Dear oVirt, We are running oVIrt SHE 4.3.3 version. We have three production DCCs/clusters: * avshared1 * avlocal1 * avlocal2 When navigating to Vitrual Machines > Selecting New VM > and changing cluster, we get an UI exception: Engine.log: 2019-07-04 12:45:27,538Z ERROR [org.ovirt.engine.core.utils.servlet.ServletUtils] (default task-468) [] Error sending file '/etc/ovirt-engine/branding/00-ovirt.brand/bundled/patternfly/fonts/fontawesome-webfont.woff2'.: java.io.IOException: Connection reset by peer at sun.nio.ch.FileDispatcherImpl.writev0(Native Method) [rt.jar:1.8.0_201] at sun.nio.ch.SocketDispatcher.writev(SocketDispatcher.java:51) [rt.jar:1.8.0_201] at sun.nio.ch.IOUtil.write(IOUtil.java:148) [rt.jar:1.8.0_201] at sun.nio.ch.SocketChannelImpl.write(SocketChannelImpl.java:504) [rt.jar:1.8.0_201] at org.xnio.nio.NioSocketConduit.write(NioSocketConduit.java:162) at io.undertow.conduits.AbstractFramedStreamSinkConduit.doWrite(AbstractFramedStreamSinkConduit.java:137) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.conduits.AbstractFramedStreamSinkConduit.write(AbstractFramedStreamSinkConduit.java:108) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.protocol.ajp.AjpServerResponseConduit.write(AjpServerResponseConduit.java:298) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at org.xnio.conduits.ConduitStreamSinkChannel.write(ConduitStreamSinkChannel.java:150) at io.undertow.channels.DetachableStreamSinkChannel.write(DetachableStreamSinkChannel.java:240) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.HttpServerExchange$WriteDispatchChannel.write(HttpServerExchange.java:2103) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.spec.ServletOutputStreamImpl.writeBufferBlocking(ServletOutputStreamImpl.java:574) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.spec.ServletOutputStreamImpl.write(ServletOutputStreamImpl.java:150) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.ovirt.engine.core.utils.servlet.ServletUtils.writeFileToStream(ServletUtils.java:145) [utils.jar:] at org.ovirt.engine.core.utils.servlet.ServletUtils.sendFile(ServletUtils.java:121) [utils.jar:] at org.ovirt.engine.core.utils.servlet.ServletUtils.sendFile(ServletUtils.java:74) [utils.jar:] at org.ovirt.engine.core.utils.servlet.ServletUtils.sendFile(ServletUtils.java:70) [utils.jar:] at org.ovirt.engine.core.branding.BrandingServlet.doGet(BrandingServlet.java:50) [branding.jar:] at javax.servlet.http.HttpServlet.service(HttpServlet.java:686) [jboss-servlet-api_4.0_spec-1.0.0.Final.jar:1.0.0.Final] at javax.servlet.http.HttpServlet.service(HttpServlet.java:791) [jboss-servlet-api_4.0_spec-1.0.0.Final.jar:1.0.0.Final] at io.undertow.servlet.handlers.ServletHandler.handleRequest(ServletHandler.java:74) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.FilterHandler$FilterChainImpl.doFilter(FilterHandler.java:129) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.ovirt.engine.core.utils.servlet.HeaderFilter.doFilter(HeaderFilter.java:94) [utils.jar:] at io.undertow.servlet.core.ManagedFilter.doFilter(ManagedFilter.java:61) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.FilterHandler$FilterChainImpl.doFilter(FilterHandler.java:131) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.ovirt.engine.core.utils.servlet.CachingFilter.doFilter(CachingFilter.java:133) [utils.jar:] at io.undertow.servlet.core.ManagedFilter.doFilter(ManagedFilter.java:61) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.FilterHandler$FilterChainImpl.doFilter(FilterHandler.java:131) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.ovirt.engine.core.branding.BrandingFilter.doFilter(BrandingFilter.java:73) [branding.jar:] at io.undertow.servlet.core.ManagedFilter.doFilter(ManagedFilter.java:61) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.FilterHandler$FilterChainImpl.doFilter(FilterHandler.java:131) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.ovirt.engine.core.utils.servlet.LocaleFilter.doFilter(LocaleFilter.java:65) [utils.jar:] at io.undertow.servlet.core.ManagedFilter.doFilter(ManagedFilter.java:61) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.FilterHandler$FilterChainImpl.doFilter(FilterHandler.java:131) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.FilterHandler.handleRequest(FilterHandler.java:84) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.security.ServletSecurityRoleHandler.handleRequest(ServletSecurityRoleHandler.java:62) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletChain$1.handleRequest(ServletChain.java:68) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletDispatchingHandler.handleRequest(ServletDispatchingHandler.java:36) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.wildfly.extension.undertow.security.SecurityContextAssociationHandler.handleRequest(SecurityContextAssociationHandler.java:78) at io.undertow.server.handlers.PredicateHandler.handleRequest(PredicateHandler.java:43) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.security.SSLInformationAssociationHandler.handleRequest(SSLInformationAssociationHandler.java:132) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.security.ServletAuthenticationCallHandler.handleRequest(ServletAuthenticationCallHandler.java:57) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.handlers.PredicateHandler.handleRequest(PredicateHandler.java:43) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.security.handlers.AuthenticationConstraintHandler.handleRequest(AuthenticationConstraintHandler.java:53) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.security.handlers.AbstractConfidentialityHandler.handleRequest(AbstractConfidentialityHandler.java:46) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.security.ServletConfidentialityConstraintHandler.handleRequest(ServletConfidentialityConstraintHandler.java:64) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.security.ServletSecurityConstraintHandler.handleRequest(ServletSecurityConstraintHandler.java:59) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.security.handlers.AuthenticationMechanismsHandler.handleRequest(AuthenticationMechanismsHandler.java:60) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.security.CachedAuthenticatedSessionHandler.handleRequest(CachedAuthenticatedSessionHandler.java:77) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.security.handlers.NotificationReceiverHandler.handleRequest(NotificationReceiverHandler.java:50) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.security.handlers.AbstractSecurityContextAssociationHandler.handleRequest(AbstractSecurityContextAssociationHandler.java:43) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.handlers.PredicateHandler.handleRequest(PredicateHandler.java:43) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at org.wildfly.extension.undertow.security.jacc.JACCContextIdHandler.handleRequest(JACCContextIdHandler.java:61) at io.undertow.server.handlers.PredicateHandler.handleRequest(PredicateHandler.java:43) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.handlers.PredicateHandler.handleRequest(PredicateHandler.java:43) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletInitialHandler.handleFirstRequest(ServletInitialHandler.java:292) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletInitialHandler.access$100(ServletInitialHandler.java:81) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletInitialHandler$2.call(ServletInitialHandler.java:138) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletInitialHandler$2.call(ServletInitialHandler.java:135) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.core.ServletRequestContextThreadSetupAction$1.call(ServletRequestContextThreadSetupAction.java:48) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.core.ContextClassLoaderSetupAction$1.call(ContextClassLoaderSetupAction.java:43) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at org.wildfly.extension.undertow.security.SecurityContextThreadSetupAction.lambda$create$0(SecurityContextThreadSetupAction.java:105) at org.wildfly.extension.undertow.deployment.UndertowDeploymentInfoService$UndertowThreadSetupAction.lambda$create$0(UndertowDeploymentInfoService.java:1502) at org.wildfly.extension.undertow.deployment.UndertowDeploymentInfoService$UndertowThreadSetupAction.lambda$create$0(UndertowDeploymentInfoService.java:1502) at org.wildfly.extension.undertow.deployment.UndertowDeploymentInfoService$UndertowThreadSetupAction.lambda$create$0(UndertowDeploymentInfoService.java:1502) at io.undertow.servlet.handlers.ServletInitialHandler.dispatchRequest(ServletInitialHandler.java:272) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletInitialHandler.access$000(ServletInitialHandler.java:81) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.servlet.handlers.ServletInitialHandler$1.handleRequest(ServletInitialHandler.java:104) [undertow-servlet-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.Connectors.executeRootHandler(Connectors.java:360) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at io.undertow.server.HttpServerExchange$1.run(HttpServerExchange.java:830) [undertow-core-2.0.15.Final.jar:2.0.15.Final] at org.jboss.threads.ContextClassLoaderSavingRunnable.run(ContextClassLoaderSavingRunnable.java:35) at org.jboss.threads.EnhancedQueueExecutor.safeRun(EnhancedQueueExecutor.java:1985) at org.jboss.threads.EnhancedQueueExecutor$ThreadBody.doRunTask(EnhancedQueueExecutor.java:1487) at org.jboss.threads.EnhancedQueueExecutor$ThreadBody.run(EnhancedQueueExecutor.java:1378) at java.lang.Thread.run(Thread.java:748) [rt.jar:1.8.0_201] ui.log: 2019-07-04 12:45:36,816Z ERROR [org.ovirt.engine.ui.frontend.server.gwt.OvirtRemoteLoggingService] (default task-468) [] Permutation name: D5BDCF23C278EDC04ACE8C382374BEA9 2019-07-04 12:45:36,818Z ERROR [org.ovirt.engine.ui.frontend.server.gwt.OvirtRemoteLoggingService] (default task-468) [] Uncaught exception: com.google.gwt.event.shared.UmbrellaException: Exception caught: undefined at java.lang.Throwable.Throwable(Throwable.java:70) [rt.jar:1.8.0_201] at java.lang.RuntimeException.RuntimeException(RuntimeException.java:32) [rt.jar:1.8.0_201] at com.google.web.bindery.event.shared.UmbrellaException.UmbrellaException(UmbrellaException.java:64) [gwt-servlet.jar:] at com.google.gwt.event.shared.UmbrellaException.UmbrellaException(UmbrellaException.java:25) [gwt-servlet.jar:] at com.google.gwt.event.shared.HandlerManager.$fireEvent(HandlerManager.java:117) [gwt-servlet.jar:] at com.google.gwt.user.client.ui.Widget.$fireEvent(Widget.java:127) [gwt-servlet.jar:] at com.google.gwt.user.client.ui.Widget.fireEvent(Widget.java:127) [gwt-servlet.jar:] at com.google.gwt.event.logical.shared.ValueChangeEvent.fire(ValueChangeEvent.java:40) [gwt-servlet.jar:] at org.ovirt.engine.ui.common.widget.editor.ListModelListBox.$lambda$2(ListModelListBox.java:251) at org.ovirt.engine.ui.common.widget.editor.ListModelListBox$lambda$2$Type.execute(ListModelListBox.java:251) at com.google.gwt.core.client.impl.SchedulerImpl.runScheduledTasks(SchedulerImpl.java:167) [gwt-servlet.jar:] at com.google.gwt.core.client.impl.SchedulerImpl.$flushPostEventPumpCommands(SchedulerImpl.java:338) [gwt-servlet.jar:] at com.google.gwt.core.client.impl.SchedulerImpl$Flusher.execute(SchedulerImpl.java:76) [gwt-servlet.jar:] at com.google.gwt.core.client.impl.SchedulerImpl.execute(SchedulerImpl.java:140) [gwt-servlet.jar:] at com.google.gwt.core.client.impl.Impl.apply(Impl.java:236) [gwt-servlet.jar:] at com.google.gwt.core.client.impl.Impl.entry0(Impl.java:275) [gwt-servlet.jar:] at Unknown.Su/<(https://ovirt-engine.avinity.tv/ovirt-engine/webadmin/?locale=en_US line 9 > scriptElement) at Unknown.d(https://ovirt-engine.avinity.tv/ovirt-engine/webadmin/?locale=en_US line 9 > scriptElement) at Unknown.anonymous(Unknown) Caused by: java.lang.NullPointerException at java.lang.Throwable.Throwable(Throwable.java:59) [rt.jar:1.8.0_201] at java.lang.Exception.Exception(Exception.java:25) [rt.jar:1.8.0_201] at java.lang.RuntimeException.RuntimeException(RuntimeException.java:25) [rt.jar:1.8.0_201] at java.lang.NullPointerException.NullPointerException(NullPointerException.java:28) [rt.jar:1.8.0_201] at javaemul.internal.InternalPreconditions.checkCriticalNotNull(InternalPreconditions.java:417) [gwt-servlet.jar:] at javaemul.internal.InternalPreconditions.checkNotNull(InternalPreconditions.java:403) [gwt-servlet.jar:] at org.ovirt.engine.ui.uicommonweb.models.vms.UnitVmModel.$compatibilityVersionChanged(UnitVmModel.java:2090) at org.ovirt.engine.ui.uicommonweb.models.vms.UnitVmModel.eventRaised(UnitVmModel.java:1962) at org.ovirt.engine.ui.uicompat.Event.$raise(Event.java:99) at org.ovirt.engine.ui.uicommonweb.models.ListModel.$setSelectedItem(ListModel.java:82) at org.ovirt.engine.ui.common.widget.uicommon.popup.AbstractVmPopupWidget_dataCenterWithClustersList_selectedItem_Context.$setInModel(AbstractVmPopupWidget_dataCenterWithClustersList_selectedItem_Context.java:19) at org.ovirt.engine.ui.common.widget.uicommon.popup.AbstractVmPopupWidget_dataCenterWithClustersList_selectedItem_Context.setInModel(AbstractVmPopupWidget_dataCenterWithClustersList_selectedItem_Context.java:19) at org.ovirt.engine.ui.common.editor.UiCommonEditorVisitor.$setInModel(UiCommonEditorVisitor.java:143) at org.ovirt.engine.ui.common.editor.UiCommonEditorVisitor.$lambda$0(UiCommonEditorVisitor.java:60) at org.ovirt.engine.ui.common.editor.UiCommonEditorVisitor$lambda$0$Type.onValueChange(UiCommonEditorVisitor.java:60) at com.google.gwt.event.logical.shared.ValueChangeEvent.dispatch(ValueChangeEvent.java:127) [gwt-servlet.jar:] at com.google.gwt.event.shared.GwtEvent.dispatch(GwtEvent.java:76) [gwt-servlet.jar:] at com.google.web.bindery.event.shared.SimpleEventBus.$doFire(SimpleEventBus.java:173) [gwt-servlet.jar:] ... 15 more Screenshot: Cluster is changed from avshared1 to avlocal1 but Templates list presented is still from avshared1: [cid:image001.png@01D53278.AE221070] I was not able to find it this was already reported and potentially solved in 4.3.4 or 4.3.5. Kindly awaiting your reply. Marko Vrgotic ActiveVideo

4 7

Re: oVirt hyerconverged more than 12 node
by Strahil 10 Jul '19

10 Jul '19

Where did you read that? It seems I can't find such statement in the web. Best Regards Strahil NikolovOn Jun 26, 2019 11:52, wodel youchi <wodel.youchi(a)gmail.com> wrote: > > Hi, > > Anyone!!!??? > > Regards. > > Le dim. 23 juin 2019 à 17:06, wodel youchi <wodel.youchi(a)gmail.com> a écrit : >> >> Hi, >> >> Could someone explain the 12 nodes limitation when installing oVirt Hyperconverged? >> >> Our client has 16 nodes, can we use them on a hyperconverged installation? for example creating two clusters, one with 9 nodes and the second with 6 nodes. >> >> Regards.

6 6

Ovirt Hyperconverged Cluster
by raffaele＠stefanile.com 10 Jul '19

10 Jul '19

I am installing ovirt 4.2 on three nodes. I am using centos with ovirt cockpit. My /sdb is my boot disk and /sda is my local storage, When I started the setup with cockpit I selected the sda but the ansible script stay on sdb. I have fix all changing the playbook manually but in the execution the gdeploy tool stay blocked on TASK [Create Physical Volume] . I don't find any logs. How I can fix that?

3 4

Regarding VDSM_Hooks
by Vrgotic, Marko 10 Jul '19

10 Jul '19

Dear oVIrt, Happy to report I have deployed my first python vdsm_hook which removes A, AAAA, TXT records of VM each time after_vm_destroy event is triggered, and it works fine. This was required to be able to quickly redploy/rebuild VMs using same hostname. Issue I am observing/just discovered now is: Since live_migration of VM guest is considered a destruction from Host perspective, DNS records get deleted and VM lands on new host without being resolvable 😊 . I would like to introduce another python script for hook regarding migration events to get these entries back into DNS but for that I need there IPs. Question: * Where can I find/locate/read VMs IPs and Hostnames (is it dom_xml) to be able to incorporate them for DNS Update script? If its relevant for the question: we are currently running oVIrt 4.3.3 version Kindly awaiting your reply. Marko Vrgotic ActiveVideo

2 4

VM Portal please add search filter box and list view as in Administration portal
by Vrgotic, Marko 10 Jul '19

10 Jul '19

Dear oVirt, This email has bounced two times already, and I am not sure what is wrong. Hopefully you get it this time. Request is below. Sent from my iPhone Dear oVirt, Would it be possible to discuss/consider adding search/filter field for VM Portal, resembling one in Administration Portal? I have 60 users with over 500VMs and it would be really good to have this option. At this moment is virtually impossible to use the VMPortal due to poor view options. We are currently running oVirt 4.3.3. — — — Met vriendelijke groet / Kind regards, Marko Vrgotic Sr. System Engineer @ System Administration m.vrgotic(a)activevideo.com<mailto:m.vrgotic@activevideo.com>

2 1

VDSM Hooks question
by Vrgotic, Marko 09 Jul '19

09 Jul '19

Dear oVirt, This request was bounced two times as well. Details below. Can you please advise me. Sent from my iPhone On 8 Jul 2019, at 09:58, Vrgotic, Marko <M.Vrgotic(a)activevideo.com<mailto:M.Vrgotic@activevideo.com>> wrote: Dear oVIrt, Happy to report I have deployed my first python vdsm_hook which removes A, AAAA, TXT records of VM each time after_vm_destroy event is triggered, and it works fine. This was required to be able to quickly redploy/rebuild VMs using same hostname. Issue I am observing/just discovered now is: Since live_migration of VM guest is considered a destruction from Host perspective, DNS records get deleted and VM lands on new host without being resolvable 😊 . I would like to introduce another python script for hook regarding migration events to get these entries back into DNS but for that I need there IPs. Question: * Where can I find/locate/read VMs IPs and Hostnames (is it dom_xml) to be able to incorporate them for DNS Update script? Or even better: * What would be even better, is there a way to not trigger the dns update if VM is being Migrated? Can I use dom_xml or other location/file to check whether VM is migrated or not, which would allow me to control if dnsupdate should be triggered? If its relevant for the question: we are currently running oVirt 4.3.3 version Kindly awaiting your reply. Marko Vrgotic ActiveVideo

1 0

Re: Ethernet tools for VM's
by Strahil 09 Jul '19

09 Jul '19

Don't forget to run a ping with a size of 8500 and "do not fragment" flag. This will really prove that you are no longer using the small MTU anywhere on the path. Best Regards, Strahil NikolovOn Jul 9, 2019 17:27, Mark Steele <msteele(a)telvue.com> wrote: > > Thank you Strahil, > > The MTU appears to be set to 1500 according to 'ifconfig'. > > Mark > > *** > Mark Steele > CIO / VP Technical Operations | TelVue Corporation > TelVue - We Share Your Vision > 16000 Horizon Way, Suite 100 | Mt. Laurel, NJ 08054 > 800.885.8886 x128 | msteele(a)telvue.com | http://www.telvue.com > twitter: http://twitter.com/telvue | facebook: https://www.facebook.com/telvue > > > On Tue, Jul 9, 2019 at 10:14 AM Strahil Nikolov <hunter86_bg(a)yahoo.com> wrote: >> >> The first thing that comes to my mind is to check the network's MTU. >> By default it is 1500, and I suppose you can go with MTU 9000 >> Also , check if OS is using MTU 9000 >> >> Best Regards, >> Strahil Nikolov >> >> В вторник, 9 юли 2019 г., 9:58:47 ч. Гринуич-4, Mark Steele <msteele(a)telvue.com> написа: >> >> >> It seems that our oVirt instance never exceeds 550Mbps aggregate traffic (rx / tx) according to nvstat. I want to make sure that the negotiated speed, handshaking, etc. are all what I expect them to be from the OS level. >> >> *** >> Mark Steele

1 0

Ethernet tools for VM's
by Mark Steele 09 Jul '19

09 Jul '19

oVirt Enginge Version: 3.5.0.1-1.el6 (yes....I know it's old) VM is running Ubuntu 18.04 with ovirt agent installed. I'm attempting to get NIC information by running 'ethtool -i ens3' I get the following: root@myserver:~# ethtool -i ens3 driver: virtio_net version: 1.0.0 firmware-version: expansion-rom-version: bus-info: 0000:00:03.0 supports-statistics: no supports-test: no supports-eeprom-access: no supports-register-dump: no supports-priv-flags: no root@myserver:~# and when I run 'ethtool ens3' I get the following: root@myserver:~# ethtool ens3 Settings for ens3: Supported ports: [ ] Supported link modes: Not reported Supported pause frame use: No Supports auto-negotiation: No Supported FEC modes: Not reported Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Advertised FEC modes: Not reported Speed: Unknown! Duplex: Unknown! (255) Port: Other PHYAD: 0 Transceiver: internal Auto-negotiation: off Link detected: yes This is not what I expected. Is there another tool I should be using to display the information for ens3 on this server? Best regards, *** *Mark Steele* CIO / VP Technical Operations | TelVue Corporation TelVue - We Share Your Vision 16000 Horizon Way, Suite 100 | Mt. Laurel, NJ 08054 800.885.8886 x128 | msteele(a)telvue.com | http://www.telvue.com twitter: http://twitter.com/telvue | facebook: https://www.facebook.com/telvue

3 5

[ANN] oVirt updates
by Sandro Bonazzola 09 Jul '19

09 Jul '19

oVirt community, Today marks a new day in the 26-year history of Red Hat. IBM has finalized its acquisition of Red Hat, which will operate as a distinct unit within IBM moving forward. What does this mean for Red Hat’s contributions to the oVirt project? In short, nothing. Red Hat always has and will continue to be a champion for open source and projects like oVirt that have played such a large role in driving innovation in the virtualization space. IBM is committed to Red Hat’s independence and role in open source software communities so that we can continue this work without interruption or changes. Our mission, governance, and objectives remain the same. We will continue to execute the existing project roadmap as we’ve been doing since 2011 for the oVirt project. Red Hat associates will continue to contribute to the upstream in the same way they have been. And, as always, we will continue to help upstream projects be successful and contribute to welcoming new members and maintaining the project. We will do this together, with the community, as we always have. If you have questions or would like to learn more about today’s news, I encourage you to review the materials below. Red Hat CTO Chris Wright will host an online Q&A session in the coming days where you can ask questions you may have about what the acquisition means for Red Hat and our involvement in open source communities. Details will be announced on the Red Hat blog [1]. * Press release [2] * Blog from Chris Wright [3] * FAQ [4] Sandro Bonazzola, Manager, Software Engineering [1] https://www.redhat.com/en/blog [2] https://www.redhat.com/en/about/press-releases/ibm-closes-landmark-acquisit… [3] https://www.redhat.com/en/blog/red-hat-and-ibm-accelerating-adoption-open-s… [4] https://community.redhat.com/blog/2019/07/faq-for-communities/

1 0

Managed Block Storage
by dan.poltawski＠tnp.net.uk 09 Jul '19

09 Jul '19

I'm testing out the managed storage to connect to ceph and I have a few questions: * Would I be correct in assuming that the hosted engine VM needs connectivity to the storage and not just the underlying hosts themselves? It seems like the cinderlib client runs from the engine? * Does the ceph config and keyring need to replicated onto each hypervisor/host? * I have managed to do one block operation so far (i've created a volume which is visible on the ceph side), but multiple other operations have failed and are 'running' in the engine task list. Is there any way I can increase debugging to see whats happening?

3 15

[ANN] oVirt 4.3.5 Fourth Release Candidate is now available for testing
by Sandro Bonazzola 09 Jul '19

09 Jul '19

The oVirt Project is pleased to announce the availability of the oVirt 4.3.5 Fourth Release Candidate for testing, as of July 3rd, 2019. While testing this release candidate please consider deeper testing on gluster upgrade since with this release we are switching from Gluster 5 to Gluster 6. This update is a release candidate of the fifth in a series of stabilization updates to the 4.3 series. This is pre-release software. This pre-release should not to be used in production. This release is available now on x86_64 architecture for: * Red Hat Enterprise Linux 7.6 or later * CentOS Linux (or similar) 7.6 or later This release supports Hypervisor Hosts on x86_64 and ppc64le architectures for: * Red Hat Enterprise Linux 7.6 or later * CentOS Linux (or similar) 7.6 or later * oVirt Node 4.3 (available for x86_64 only) See the release notes [1] for installation / upgrade instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is laready available - oVirt Node is already available[2] Additional Resources: * Read more about the oVirt 4.3.5 release highlights: http://www.ovirt.org/release/4.3.5/ * Get more oVirt Project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] http://www.ovirt.org/release/4.3.5/ [2] http://resources.ovirt.org/pub/ovirt-4.3-pre/iso/ -- Sandro Bonazzola MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV Red Hat EMEA <https://www.redhat.com/> sbonazzo(a)redhat.com <https://www.redhat.com/>

3 4

Storage domain format version info
by Gianluca Cecchi 09 Jul '19

09 Jul '19

Hello, part of updating a DC from 4.2 to 4.3 consists in updating format of data storage domains from V4 to V5. Questions: - where can I find list of differences between V4 and V5? And in general between previous ones? - can I force only a particular storage domain to remain in V4 while having the other ones upgraded to V5, for any reason? Or the reverse: update only one of the defined domains? Eg on oVirt web site I only found this for V4 https://www.ovirt.org/develop/release-management/features/storage/storage_d… with mention about Qcow2 v3 (link broken.. one ot the upstream pages for it here: https://wiki.qemu.org/Features/Qcow3 ) that should give near raw performance with advantages of qcow2 format... Thanks, Gianluca

3 2

Ovirt Secure boot issues
by Strahil 08 Jul '19

08 Jul '19

Hello All, I would like to ask any of you to do a simple test. Please install a linux on a VM with Secure boot and after the install wizzard is over -power it off and then on. Here is what I have observed: 1. UEFI forgets the certificates after a poweroff and asks for the openSUSE certificate every time. Rebooting from the VM doesn't cause any problems till nextg boot. 2. RHEL8 grub menu consists only of 'System setup'. When you select it - you are sent to the UEFI menu. If you select continue - everything is fine. Poweroff + Poweron makes everything to repeat. Do you observe the same issues. If I'm not the only one hitting this - I will open a bug, otherwise I will try to further debug this. Best Regards, Strahil Nikolov

2 2

VM lost conection.
by Julio Cesar Bustamante 08 Jul '19

08 Jul '19

Hi there, I have a problem, Last week I lost connectivity a VM with OS Windows server 2008 I access to check it and in ovirtmanager that VM is power on and I could login it, but there was no ping to other VM machines So I restarted VM and I recovery connectivity. Today It shows the same scenario with same VM. I checked log from ovirtmananer and ovirt node from running VM but I didnt find any error. Where can I find out more ? I have a Ovirtmanager 4 and a Ovirtnode 4.1 [image: imagen.png] -- Julio Cesar Bustamante.

1 0

Re: HE deployment failing
by Strahil 08 Jul '19

08 Jul '19

Yes, But I thought that cockpit should prevent creation of the gluster volume 'engine' as it is too small. @Dev Do we have such control ? Best Regards, Strahil Nikolov On Jul 8, 2019 09:19, Parth Dhanjal <dparth(a)redhat.com> wrote: > > Hey! > > The other 2 bricks were of 50G each. > I forgot to check that. > Sorry for the confusion. > Thanks! > > On Mon, Jul 8, 2019 at 11:42 AM Sahina Bose <sabose(a)redhat.com> wrote: >> >> >> >> On Mon, Jul 8, 2019 at 11:40 AM Parth Dhanjal <dparth(a)redhat.com> wrote: >>> >>> Hey! >>> >>> I used cockpit to deploy gluster. >>> And the problem seems to be with >>> 10.xx.xx.xx9:/engine 50G 3.6G 47G 8% /rhev/data-center/mnt/glusterSD/10.70.41.139:_engine >>> >>> Engine volume has 500G available >>> Filesystem Size Used Avail Use% Mounted on >>> /dev/mapper/gluster_vg_sdb1-gluster_lv_engine 500G 37M 500G 1% /gluster_bricks/engine >> >> >> Check that you have 500G on all the bricks of the volume if you're using replica 3. It takes the minimum of the 3 bricks. >> >>> >>> On Fri, Jul 5, 2019 at 8:05 PM Strahil Nikolov <hunter86_bg(a)yahoo.com> wrote: >>>> >>>> Parth, >>>> >>>> did you use cockpit to deploy the gluster volume ? >>>> it's interesting why the cockpit allowed the engine's volume to be so small ... >>>> >>>> Best Regards, >>>> Strahil Nikolov >>>> >>>> В петък, 5 юли 2019 г., 10:17:11 ч. Гринуич-4, Simone Tiraboschi <stirabos(a)redhat.com> написа: >>>> >>>> >>>> >>>> >>>> On Fri, Jul 5, 2019 at 4:12 PM Parth Dhanjal <dparth(a)redhat.com> wrote: >>>>> >>>>> Hey! >>>>> >>>>> I'm trying to deploy a 3 node cluster with gluster storage. >>>>> After the gluster deployment is completed successfully, the creation of storage domain fails during HE deployment giving the error: >>>>>

1 0

4.2.8: NPE starting a specific VM
by Richard Chan 08 Jul '19

08 Jul '19

Encountering a NPE on 4.2.8. This is the first start after a 4.1 to 4.2 upgrade. 2019-07-05 15:36:56,912+08 ERROR [org.ovirt.engine.core.vdsbroker.CreateVDSCommand] (EE-ManagedThreadFactory-engine-Thread-45700) [64500cdd-b623-4bb1-a7a1-841 6b4e6723b] Failed to create VM: java.lang.NullPointerException at org.ovirt.engine.core.vdsbroker.builder.vminfo.LibvirtVmXmlBuilder.lambda$writeInterfaces$26(LibvirtVmXmlBuilder.java:1198) [vdsbroker.jar:] at java.util.Comparator.lambda$comparing$77a9974f$1(Comparator.java:469) [rt.jar:1.8.0_212] at java.util.TimSort.countRunAndMakeAscending(TimSort.java:355) [rt.jar:1.8.0_212] at java.util.TimSort.sort(TimSort.java:220) [rt.jar:1.8.0_212] at java.util.Arrays.sort(Arrays.java:1512) [rt.jar:1.8.0_212] at java.util.stream.SortedOps$SizedRefSortingSink.end(SortedOps.java:348) [rt.jar:1.8.0_212] at java.util.stream.AbstractPipeline.copyInto(AbstractPipeline.java:483) [rt.jar:1.8.0_212] at java.util.stream.AbstractPipeline.wrapAndCopyInto(AbstractPipeline.java:472) [rt.jar:1.8.0_212] at java.util.stream.ForEachOps$ForEachOp.evaluateSequential(ForEachOps.java:151) [rt.jar:1.8.0_212] at java.util.stream.ForEachOps$ForEachOp$OfRef.evaluateSequential(ForEachOps.java:174) [rt.jar:1.8.0_212] at java.util.stream.AbstractPipeline.evaluate(AbstractPipeline.java:234) [rt.jar:1.8.0_212] at java.util.stream.ReferencePipeline.forEach(ReferencePipeline.java:418) [rt.jar:1.8.0_212] at org.ovirt.engine.core.vdsbroker.builder.vminfo.LibvirtVmXmlBuilder.writeInterfaces(LibvirtVmXmlBuilder.java:1199) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.builder.vminfo.LibvirtVmXmlBuilder.writeDevices(LibvirtVmXmlBuilder.java:1045) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.builder.vminfo.LibvirtVmXmlBuilder.buildCreateVm(LibvirtVmXmlBuilder.java:254) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.vdsbroker.CreateBrokerVDSCommand.generateDomainXml(CreateBrokerVDSCommand.java:93) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.vdsbroker.CreateBrokerVDSCommand.createInfo(CreateBrokerVDSCommand.java:50) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.vdsbroker.CreateBrokerVDSCommand.executeVdsBrokerCommand(CreateBrokerVDSCommand.java:42) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.vdsbroker.VdsBrokerCommand.executeVdsCommandWithNetworkEvent(VdsBrokerCommand.java:123) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.vdsbroker.VdsBrokerCommand.executeVDSCommand(VdsBrokerCommand.java:111) [vdsbroker.jar:] at org.ovirt.engine.core.vdsbroker.VDSCommandBase.executeCommand(VDSCommandBase.java:73) [vdsbroker.jar:] at org.ovirt.engine.core.dal.VdcCommandBase.execute(VdcCommandBase.java:33) [dal.jar:] This leads to Failed to run VM message. Any ideas? Thanks Richard Chan

3 5

HE deployment failing
by Parth Dhanjal 08 Jul '19

08 Jul '19

Hey! I'm trying to deploy a 3 node cluster with gluster storage. After the gluster deployment is completed successfully, the creation of storage domain fails during HE deployment giving the error: [ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "Error: the target storage domain contains only 46.0GiB of available space while a minimum of 61.0GiB is required If you wish to use the current target storage domain by extending it, make sure it contains nothing before adding it."} I have tried to increase the disk size(provided in storage tab) to 90GiB. But the deployment still fails. A 50GiB storage domain is created by default even if some other size is provided. Has anyone faced a similar issue? Regards Parth Dhanjal

4 6

Re: UI - cannot remove disk whiel system is running
by Strahil 07 Jul '19

07 Jul '19

Everything ended well - despite the warning 'do not shutdown' I powered off and powered on the VM. This action allowed me to trigger a snapshot deletion (again) and it completed successfully. Removing the disk of interest also completed successfully. So, I got a happy ending. Best Regards, Strahil NikolovOn Jul 7, 2019 17:41, Strahil <hunter86_bg(a)yahoo.com> wrote: > > I think I'm getting closer. > > It seems the snapshot of the VM did not get deleted and that might be the problem. > > Can someone give me a hint how to remove the snapshot as I get an error: > > Cannot remove Snapshot. The following disks are in ILLEGAL status: uyuni-OS-Disk1 - please remove them and try again. > > Yet, removal of the disk cannot happen as I got: > Cannot detach Virtual Disk. The disk is already configured in a snapshot. In order to detach it, remove the disk's snapshot. > > This seems like 'Catch 22' . > > Best Regards, > Strahil Nikolov > > On Jul 7, 2019 17:30, Strahil <hunter86_bg(a)yahoo.com> wrote: >> >> Hello All, >> >> I have changed my system layout and the old disk is removed (echo 1 > /sys/block/sdX/device/delete) from OS, but UI complains when I try to remove with the following error: >> >> Error while executing action: Cannot remove Virtual Disk. At least one of the VMs is not down. >> >> Is it a limitation of oVirt ? If so, I will open an enhancement entry in bugzilla. >> >> As far as I remember KVM allowed me to make such stuff without any issues so far. >> >> Best Regards, >> Strahil Nikolov

1 0

Re: UI - cannot remove disk whiel system is running
by Strahil 07 Jul '19

07 Jul '19

I think I'm getting closer. It seems the snapshot of the VM did not get deleted and that might be the problem. Can someone give me a hint how to remove the snapshot as I get an error: Cannot remove Snapshot. The following disks are in ILLEGAL status: uyuni-OS-Disk1 - please remove them and try again. Yet, removal of the disk cannot happen as I got: Cannot detach Virtual Disk. The disk is already configured in a snapshot. In order to detach it, remove the disk's snapshot. This seems like 'Catch 22' . Best Regards, Strahil NikolovOn Jul 7, 2019 17:30, Strahil <hunter86_bg(a)yahoo.com> wrote: > > Hello All, > > I have changed my system layout and the old disk is removed (echo 1 > /sys/block/sdX/device/delete) from OS, but UI complains when I try to remove with the following error: > > Error while executing action: Cannot remove Virtual Disk. At least one of the VMs is not down. > > Is it a limitation of oVirt ? If so, I will open an enhancement entry in bugzilla. > > As far as I remember KVM allowed me to make such stuff without any issues so far. > > Best Regards, > Strahil Nikolov

1 0

UI - cannot remove disk whiel system is running
by Strahil 07 Jul '19

07 Jul '19

Hello All, I have changed my system layout and the old disk is removed (echo 1 > /sys/block/sdX/device/delete) from OS, but UI complains when I try to remove with the following error: Error while executing action: Cannot remove Virtual Disk. At least one of the VMs is not down. Is it a limitation of oVirt ? If so, I will open an enhancement entry in bugzilla. As far as I remember KVM allowed me to make such stuff without any issues so far. Best Regards, Strahil Nikolov

1 0

VM snapshot - some info needed
by Strahil Nikolov 07 Jul '19

07 Jul '19

Hello Community, I have noticed that if I want a VM snapshot with memory - I get a warning "The VM will be paused while saving the memory" .Is there a way to make snapshot without pausing the VM for the whole duration ? I have noticed that it doesn't matter if VM has qemu-guest-agent or ovirt-guest-agent. Thanks in advance for sharing your thoughts. Best Regards,Strahil Nikolov

2 2

Experience 4.1.x -> 4.2.8 -> 4.3.4 upgrade lessons
by Richard Chan 07 Jul '19

07 Jul '19

Hi oVirters, Did a 4.1 - > 4.2.8 -> 4.3.4 upgrade in two hops. Here is my experience, hope it can save you some pain. Gotchas 1. For shutdown VMs, their disks were deactivated (though still attached) 2. For shutdown VMs, their NICs were "Up" but "Unplugged" 3. VM Custom Compatibility Version is hard to find. (If it is too old say 3.6, 4.1) they won't start up. The location is: VM -> Edit -> System -> Advanced Parameters (click this) "Advanced Parameters" is an expandable widget that is quite small when collapsed. When it is expanded then you will see "Custom Compatibility Version" 4. Storage Domain migration to V5: I use a NFS storoage domain. This is migrated to the "V5" format and a lot of cleanup is done. If you have stray files or images not owned by 36:36 (vdsm:kvm on my NFS server), the V5 upgrade will fail, there will be no SPM, and the Data Center will oscillate between Non-responsive and Contending. Why would there be non 36:36 uid/gid files? This is a long story, but from the older 3.x days when there was less functionality, we would sometimes directly manipulate the filesystem and/or qcow2 images using guestfish or equivalent tools which would change the owner to qemu:qemu. Forgetting to chown back to vdsm:kvm is a recipe for pain. Cheers! -- Richard Chan

2 1

Re: Upgraded to 4.3: getting SpmStart failure
by Strahil 07 Jul '19

07 Jul '19

Can you run the engine manually on another server ? hosted-engine --vm-start Best Regards, Strahil NikolovOn Jul 5, 2019 18:05, Richard Chan <richard(a)treeboxsolutions.com> wrote: > > My engine is getting SpmStart failure. > > What is the best way to troubleshoot this? > > > -- > Richard Chan >

3 3

Ovirt 4.3.5.3-1.el7 manual migration fails
by Strahil 06 Jul '19

06 Jul '19

Hey Community, Can someone tell me which log should be checked - as one of my VMs cannot be live migrated. In this case it get's stuck at 99% for several minutes and then fails. Best Regards, Strahil Nikolov

1 0

importing a vm is always very slow
by Crazy Ayansh 05 Jul '19

05 Jul '19

Hi Users, Why importing the vm from export domain is very slow and how can we do it fast ? How to cancel a import process ? [image: image.png] Thanks

1 0

Upgraded to 4.3: getting SpmStart failure
by Richard Chan 05 Jul '19

05 Jul '19

My engine is getting SpmStart failure. What is the best way to troubleshoot this? -- Richard Chan

1 0

Anaconda crashing on start while trying to Install oVirt Node on bare metal
by rubentrindade＠live.com 05 Jul '19

05 Jul '19

Hello there! I'm trying to install an oVirt node(the most stable recent one) on a machine(just in case you didn't figure from the title :P) and anaconda just crashes \o/ I've tried to start anaconda in text mode, but the error is the exact same. Here's a screenshot of the event(text mode, although it shouldn't matter): https://i.imgur.com/ihO1xWP.jpg The only "disk" attached to the machine has no partitions, it's absolutely clean. The machine in question is a PowerEdge M520, if that matters, and I'm trying to install on top of a pair of 32GB mirrored SD cards. I installed CentOS7 on a machine that's virtually the same(they're the exact same, but aren't the same machine) and didn't have any problem. I just have no idea. Never encountered such problem. So any help would be very appreciated. Thanks ^^

2 3

Re: [ovirt-devel] USB on host support?
by Juan Pablo Lorier 05 Jul '19

05 Jul '19

I'm having a similar problem. The passtrough needs 2 steps, the first is to attach the host device to the VM, but if you don't enable the spice usb the vm fails to start. I don't know if the USB works straight from the host device or if it depends on the spice console. In my case, a device that work in a windows 10 pc doesn't work in a windows 10 vm. Maybe we both can get help in this matter. Regards El 1/7/19 a las 13:02, users-request(a)ovirt.org escribió: > Send Users mailing list submissions to > users(a)ovirt.org > > To subscribe or unsubscribe via email, send a message with subject or > body 'help' to > users-request(a)ovirt.org > > You can reach the person managing the list at > users-owner(a)ovirt.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of Users digest..." > > Today's Topics: > > 1. Re: Failed on HE-Storage migration (Strahil Nikolov) > 2. Adding a custom fence agent on 4.3.4 (Matteo) > 3. USB host support? (Hetz Ben Hamo) > 4. Re: [ovirt-devel] USB on host support? (Hetz Ben Hamo) > 5. Re: Ovirt Hyperconverged Cluster (Stefanile Raffaele) > > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/

4 3

4.3 won't upgrade engine in standalone KVM VM: low_custom_compatibility_version 'agent03'
by Richard Chan 05 Jul '19

05 Jul '19

Hi, I am running 4.2 engine in a standalone libvirt KVM VM (running on a hypervisor that is not part of the oVirt infrastructure); i.e., I am not using hosted engine but still running engine in a VM. Now 4.3 won't upgrade inside this libvirt KVM VM: Failed to execute stage 'Setup validation': Cannot upgrade the Engine due to low custom_compatibility_version for virtual machines: ['agent03']. Please edit this virtual machines, in edit VM dialog go to System->Advanced Parameters -> Custom Compatibility Version and either reset to empty (cluster default) or set a value supported by the new installation: 4.1, 4.2, 4.3. engine-setup has probably detected that it is running inside a VM: 1. Where did it get 'agent03' string from 2. Any suggestions how to fool engine-setup to think this is 4.3 Here is the dmidecode of the standalone engine VM: # dmidecode 3.1 Getting SMBIOS data from sysfs. SMBIOS 2.8 present. 11 structures occupying 591 bytes. Table at 0xBFED7000. Handle 0x0100, DMI type 1, 27 bytes System Information Manufacturer: Red Hat Product Name: KVM Version: RHEL 7.3.0 PC (i440FX + PIIX, 1996) Serial Number: Not Specified UUID: cdb0f3fd-42c7-4a16-bcd1-5d65f19aca19 Wake-up Type: Power Switch SKU Number: Not Specified Family: Red Hat Enterprise Linux Handle 0x0300, DMI type 3, 21 bytes Chassis Information Manufacturer: Red Hat Type: Other Lock: Not Present Version: RHEL 7.3.0 PC (i440FX + PIIX, 1996) Serial Number: Not Specified Asset Tag: Not Specified Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: Unknown OEM Information: 0x00000000 Height: Unspecified Number Of Power Cords: Unspecified Contained Elements: 0 Handle 0x0400, DMI type 4, 42 bytes Processor Information Socket Designation: CPU 0 Type: Central Processor Family: Other Manufacturer: Red Hat ID: C1 06 03 00 FF FB 8B 07 Version: RHEL 7.3.0 PC (i440FX + PIIX, 1996) Voltage: Unknown External Clock: Unknown Max Speed: 2000 MHz Current Speed: 2000 MHz Status: Populated, Enabled Upgrade: Other L1 Cache Handle: Not Provided L2 Cache Handle: Not Provided L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Core Count: 1 Core Enabled: 1 Thread Count: 1 Characteristics: None Handle 0x0401, DMI type 4, 42 bytes Processor Information Socket Designation: CPU 1 Type: Central Processor Family: Other Manufacturer: Red Hat ID: C1 06 03 00 FF FB 8B 07 Version: RHEL 7.3.0 PC (i440FX + PIIX, 1996) Voltage: Unknown External Clock: Unknown Max Speed: 2000 MHz Current Speed: 2000 MHz Status: Populated, Enabled Upgrade: Other L1 Cache Handle: Not Provided L2 Cache Handle: Not Provided L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Core Count: 1 Core Enabled: 1 Thread Count: 1 Characteristics: None Handle 0x1000, DMI type 16, 23 bytes Physical Memory Array Location: Other Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 8 GB Error Information Handle: Not Provided Number Of Devices: 1 Handle 0x1100, DMI type 17, 40 bytes Memory Device Array Handle: 0x1000 Error Information Handle: Not Provided Total Width: Unknown Data Width: Unknown Size: 8192 MB Form Factor: DIMM Set: None Locator: DIMM 0 Bank Locator: Not Specified Type: RAM Type Detail: Other Speed: Unknown Manufacturer: Red Hat Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Rank: Unknown Configured Clock Speed: Unknown Minimum Voltage: Unknown Maximum Voltage: Unknown Configured Voltage: Unknown Handle 0x1300, DMI type 19, 31 bytes Memory Array Mapped Address Starting Address: 0x00000000000 Ending Address: 0x000BFFFFFFF Range Size: 3 GB Physical Array Handle: 0x1000 Partition Width: 1 Handle 0x1301, DMI type 19, 31 bytes Memory Array Mapped Address Starting Address: 0x00100000000 Ending Address: 0x0023FFFFFFF Range Size: 5 GB Physical Array Handle: 0x1000 Partition Width: 1 Handle 0x2000, DMI type 32, 11 bytes System Boot Information Status: No errors detected Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: EFI Development Kit II / OVMF Version: 0.0.0 Release Date: 02/06/2015 Address: 0xE8000 Runtime Size: 96 kB ROM Size: 64 kB Characteristics: BIOS characteristics not supported Targeted content distribution is supported UEFI is supported System is a virtual machine BIOS Revision: 0.0 Handle 0xFEFF, DMI type 127, 4 bytes End Of Table Cheers -- Richard Chan

2 6

Any one uses Nvidia T4 as vGPU in production?
by Arman Khalatyan 05 Jul '19

05 Jul '19

Hello, any successful stories of the Nvidia T4 usage with the Ovirt? I was wondered if one would get 2 hosts each with T4s , are there live migrations possible? thanks, Arman

2 1

Re: Bad Gateway buhaa
by Dominik Holler 05 Jul '19

05 Jul '19

On Fri, 5 Jul 2019 07:24:37 +0000 "Vrgotic, Marko" <M.Vrgotic(a)activevideo.com> wrote: > This is great Dominik, > > I promise to send my feedback by end of this week. > Great! There is a talk on conceptual level in https://archive.fosdem.org/2018/schedule/event/vai_leveraging_sdn_for_virtu… which might be interesting for you, too. > — — — > Met vriendelijke groet / Best regards, > > Marko Vrgotic > Sr. System Engineer > ActiveVideo > > Tel. +31 (0)35 677 4131 > email: m.vrgotic(a)activevideo.com > skype: av.mvrgotic.se > www.activevideo.com > ________________________________ > From: Dominik Holler <dholler(a)redhat.com> > Sent: Friday, July 5, 2019 8:42:01 AM > To: Vrgotic, Marko > Cc: users(a)ovirt.org; Miguel Duarte de Mora Barroso > Subject: Re: [ovirt-users] Bad Gateway buhaa > > On Fri, 5 Jul 2019 06:36:15 +0000 > "Vrgotic, Marko" <M.Vrgotic(a)activevideo.com> wrote: > > > Thank you Dominik, > > > > I will look into ovn-provider configuration than. > > > > It is step 8 in > https://www.ovirt.org/documentation/admin-guide/chap-External_Providers.htm… > > > Where can I found some more technical information on ovn-provider (is it in any way related to openvswitch) and how it’s utilized by oVirt? I am talking besides oVirt online documentation. > > > > Happy you ask! > We have created the document > https://github.com/oVirt/ovirt-provider-ovn/blob/master/docs/provider_api_d… > and would be interested in your feedback, to improve it. > > > > > — — — > > Met vriendelijke groet / Best regards, > > > > Marko Vrgotic > > Sr. System Engineer > > ActiveVideo > > > > Tel. +31 (0)35 677 4131 > > email: m.vrgotic(a)activevideo.com > > skype: av.mvrgotic.se > > www.activevideo.com<http://www.activevideo.com> > > ________________________________ > > From: Dominik Holler <dholler(a)redhat.com> > > Sent: Friday, July 5, 2019 8:06:29 AM > > To: Vrgotic, Marko > > Cc: users(a)ovirt.org > > Subject: Re: [ovirt-users] Bad Gateway buhaa > > > > On Thu, 4 Jul 2019 13:10:52 +0000 > > "Vrgotic, Marko" <M.Vrgotic(a)activevideo.com> wrote: > > > > > Dear oVIrt, > > > > > > Although it should be simple, I am failing to understand the connection between Default Gateway setting and Bad Gateway issue. > > > > > > On which network I need to set default gateway: > > > > > > Our ovirtmgmt is set not to be used by Guest VMs, only Hosted-Engine. > > > > > > We have tenant1 network which is assigned to VM Guest instances and it has Default Gateway, working one 😊. > > > Why am I still seeing this message: > > > > > > 2019-07-04 12:53:08,991Z ERROR [org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-54) [2cfff521] Command 'org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand' failed: EngineException: (Failed with error Bad Gateway and code 5050) > > > > > > What am I doing wrong? > > > > > > > > > There seems to be a problem with the configuration of the > > ovirt-provider-ovn. If you do not want to use OVN networking, you can > > just disable the "Automatic Synchronization" of the ovirt-provider-ovn. > > > > > If you need more info or log data, just let me know. > > > > > > oVIrt 4.3.3 > > > > > > Kindly awating your reply. > > > > > > Marko Vrgotic > > > ActiveVideo > > >

1 0

Re: Bad Gateway buhaa
by Dominik Holler 05 Jul '19

05 Jul '19

On Fri, 5 Jul 2019 06:36:15 +0000 "Vrgotic, Marko" <M.Vrgotic(a)activevideo.com> wrote: > Thank you Dominik, > > I will look into ovn-provider configuration than. > It is step 8 in https://www.ovirt.org/documentation/admin-guide/chap-External_Providers.htm… > Where can I found some more technical information on ovn-provider (is it in any way related to openvswitch) and how it’s utilized by oVirt? I am talking besides oVirt online documentation. > Happy you ask! We have created the document https://github.com/oVirt/ovirt-provider-ovn/blob/master/docs/provider_api_d… and would be interested in your feedback, to improve it. > > — — — > Met vriendelijke groet / Best regards, > > Marko Vrgotic > Sr. System Engineer > ActiveVideo > > Tel. +31 (0)35 677 4131 > email: m.vrgotic(a)activevideo.com > skype: av.mvrgotic.se > www.activevideo.com > ________________________________ > From: Dominik Holler <dholler(a)redhat.com> > Sent: Friday, July 5, 2019 8:06:29 AM > To: Vrgotic, Marko > Cc: users(a)ovirt.org > Subject: Re: [ovirt-users] Bad Gateway buhaa > > On Thu, 4 Jul 2019 13:10:52 +0000 > "Vrgotic, Marko" <M.Vrgotic(a)activevideo.com> wrote: > > > Dear oVIrt, > > > > Although it should be simple, I am failing to understand the connection between Default Gateway setting and Bad Gateway issue. > > > > On which network I need to set default gateway: > > > > Our ovirtmgmt is set not to be used by Guest VMs, only Hosted-Engine. > > > > We have tenant1 network which is assigned to VM Guest instances and it has Default Gateway, working one 😊. > > Why am I still seeing this message: > > > > 2019-07-04 12:53:08,991Z ERROR [org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-54) [2cfff521] Command 'org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand' failed: EngineException: (Failed with error Bad Gateway and code 5050) > > > > What am I doing wrong? > > > > > There seems to be a problem with the configuration of the > ovirt-provider-ovn. If you do not want to use OVN networking, you can > just disable the "Automatic Synchronization" of the ovirt-provider-ovn. > > > If you need more info or log data, just let me know. > > > > oVIrt 4.3.3 > > > > Kindly awating your reply. > > > > Marko Vrgotic > > ActiveVideo >

2 1

Bad Gateway buhaa
by Vrgotic, Marko 05 Jul '19

05 Jul '19

Dear oVIrt, Although it should be simple, I am failing to understand the connection between Default Gateway setting and Bad Gateway issue. On which network I need to set default gateway: Our ovirtmgmt is set not to be used by Guest VMs, only Hosted-Engine. We have tenant1 network which is assigned to VM Guest instances and it has Default Gateway, working one 😊. Why am I still seeing this message: 2019-07-04 12:53:08,991Z ERROR [org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-54) [2cfff521] Command 'org.ovirt.engine.core.bll.provider.network.SyncNetworkProviderCommand' failed: EngineException: (Failed with error Bad Gateway and code 5050) What am I doing wrong? If you need more info or log data, just let me know. oVIrt 4.3.3 Kindly awating your reply. Marko Vrgotic ActiveVideo

2 2

How to set custom VM property in ovirt ?
by TranceWorldLogic . 05 Jul '19

05 Jul '19

Hi, I want to set custom vm property as shown below testme = String1:45;String2:67; I know engine-config command to run in ovirt, but not able to construct regular expresion. Please help me. engine-config -s UserDefinedVMProperties='multiq=<regex>' I tried below regex but server throw 500 error code after setting property. regex =(^[a-z_A-Z0-9]+:[0-9]+\;)+$ And even if match entire contain as string that also fine for me. Please please help me. Thanks, ~Rohit

1 1

Re: Anaconda crashing on start while trying to Install oVirt Node on bare metal
by Strahil 04 Jul '19

04 Jul '19

If you don't have a raid controller with battery-backed cache - disable the raid in bios. Fake raids are just like software raid, use the cpu for calculations and could be a potential problem if the Motherboard dies. Software raid (controlled by mdadm) and lvm raid (sane driver but controlled from lvm) can easily be recovered on any type of linux (as long as it is not too old ofc) and do not have the minuses of the fake raid. Best Regards, Strahil NikolovOn Jul 4, 2019 13:41, rubentrindade(a)live.com wrote: > > So, following your advise, what I did was "dd status=progress if=/dev/zero of=/dev/sda count=1" and that did indeed fix the anaconda starting up issue. > > By the way, when I said mirrored, it's raid 1, so if I do to one, I do on both at the same time. The raid is being done and managed on the bios. Maybe poor wording on my side. > > The thing is, as soon as I try to create partitions/LVMs it returns me an error. Here's the three different outputs: > LVM Thin Provisioning https://i.imgur.com/tfbi0oo.jpg (curiously, it's the same output error as when it crashed) > LVM https://i.imgur.com/nJXo3aK.jpg > Standard Partition https://i.imgur.com/j6gNRpo.jpg > > After taking the screenshots above, I tried the same process using a CentOS7 minimal image on text mode to see the output, and there's no error output what so ever. > Out of curiosity, I tried with a 4.3.3 ovirt node image and I had similar error as above(above I'm using 4.3.4) with a slight different wording, but still the same issue. > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/23EXVASBCCERK…

1 0

Re: lvm agregation of lun in a storage domain
by Strahil 04 Jul '19

04 Jul '19

I think the simplest way is to get a new LUN and migrate the VM disks to it. Once the 2 old LUNs are free - you can release them both. Best Regards, Strahil NikolovOn Jul 4, 2019 12:06, Nathanaël Blanchet <blanchet(a)abes.fr> wrote: > > Hello > > We made a mistake at the conception of our storage domain and we aggreggated two FC luns like so: > > We need to retrieve one of the two luns for other use, is there a way to easy detach one of the two luns from the VG ? > > > -- > > Nathanaël Blanchet > > > > Supervision réseau > > Pôle Infrastrutures Informatiques > > 227 avenue Professeur-Jean-Louis-Viala > > 34193 MONTPELLIER CEDEX 5 > > Tél. 33 (0)4 67 54 84 55 > > Fax 33 (0)4 67 54 84 14 > > blanchet(a)abes.fr

1 0

Can't unsubscribe myself from here
by csi-laser＠cisco.com 04 Jul '19

04 Jul '19

Hi, I sent a mail in order to unsubsribe my mailer team "csi-laser(a)cisco.com", and I'm still getting e-mails. I already sent mails to "'users-leave(a)ovirt.org' Who should I talk more in order it'll stop ??

2 1

lvm agregation of lun in a storage domain
by Nathanaël Blanchet 04 Jul '19

04 Jul '19

Hello We made a mistake at the conception of our storage domain and we aggreggated two FC luns like so: We need to retrieve one of the two luns for other use, is there a way to easy detach one of the two luns from the VG ? -- Nathanaël Blanchet Supervision réseau Pôle Infrastrutures Informatiques 227 avenue Professeur-Jean-Louis-Viala 34193 MONTPELLIER CEDEX 5 Tél. 33 (0)4 67 54 84 55 Fax 33 (0)4 67 54 84 14 blanchet(a)abes.fr

2 1

console issue after installing 3rd party certificate
by ada per 04 Jul '19

04 Jul '19

Hello Everyone, I followed the instructions on installing a 3rd party certificate on hosted engine. The certificate is installed properly and in all the correct paths, everything seems to be working fine but i cannot access teh spice console, it comes up with error cannot connect to graphic server and libvirt uri:none. any advice will be greatly appreciated

2 2

Issue adding Network to host with Python SDK
by Don Dupuis 04 Jul '19

04 Jul '19

I am having issue with adding network to host nic with python SDK. It works just fine using the portal GUI. I have the following: bond0 that is setup as mode 4 bond0.120 that is attached to ovirtmgmt network bond0.96 that I am trying to attach a new installed network called External. Below is a code snippet of what I am trying to do: hosts_service = connection.system_service().hosts_service() host = hosts_service.list(search='name=%s' % HOSTNAME)[0] host_service = hosts_service.host_service(host.id) hostnics_service = hosts_service.host_service(host.id).nics_service() n = None for n in hostnics_service.list(): if n.name == 'bond0.96': n_id = n.id print("n is %s" % n_id) system_service = connection.system_service() networks_service = connection.system_service().networks_service() network = networks_service.list( search='name=External and datacenter=%s-local' % HOSTNAME) [0] print ("Network name is %s" % network.name) print ("Network id is %s" % network.id) net_attachments_service = host_service.network_attachments_service() net_attachment = net_attachments_service.add( types.NetworkAttachment( network=types.Network(id=network.id), host_nic=types.HostNic(name='bond0.96') ), ), I will end up with an error of File "./add_host_py", line 193, in Add_External_network host_nic=types.HostNic(name='bond0.96') File "/usr/lib64/python2.7/site-packages/ovirtsdk4/services.py", line 15441, in add self._check_fault(response) File "/usr/lib64/python2.7/site-packages/ovirtsdk4/service.py", line 98, in _check_fault Service._raise_error(response, fault) File "/usr/lib64/python2.7/site-packages/ovirtsdk4/service.py", line 71, in _raise_error raise Error(msg) ovirtsdk4.Error: Fault reason is "Operation Failed". Fault detail is "[Cannot setup Networks. The attachment of network 'External' references vlan device 'bond0.96'. Network attachment cannot reference vlan device.]". HTTP response code is 400. Can someone guide me on what I am doing wrong or not understanding with the NetworkAttachment Service? Thanks Don

2 4

Spice console very poor performance for Windows 10 vm
by Leo David 04 Jul '19

04 Jul '19

Hello Everyone, Maybe I am something wrong, but spice console seem to be very laggy and slow for windows 10 vms. I have tried both qxl and qxl-dod drivers, but no luck so far... As a notice, the Win 2012R2 vm console is running fine, the problem seems to only affect Windows 10. Any ideas, what should I do to sort this out ? Thank you very much ! Leo -- Best regards, Leo David

6 22

Re: Disk latency is very high, time taken to copy 1M file is > 10s
by Strahil 03 Jul '19

03 Jul '19

Mount your disk (/mnt/) and try the following command(taken from the previous output): dd if=/dev/zero of=/mnt/small.file bs=512 count=2050 oflag=direct How much time does it take? Best Regards, Strahil NikolovOn Jul 3, 2019 13:27, PS Kazi <faruk.apsara(a)gmail.com> wrote: > > hi, > I am using HDD : Toshiba 7200 RPM, Data transfer Rate 150MB/s, Interface 6Gb/s. > But Hyper-converged configuration stopped with error msg: Disk latency is very high, time taken to copy 1M file is > 10s > Please help me to stop this error. > ________________________________________________________________________________________ > TASK [gluster.features/roles/gluster_hci : Check if time taken to copy 1M file (512B chunks) is < 10s] *** > failed: [ov-node-1.hci.com -> ov-node-1.hci.com] (item=11.9508) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.966178", "end": "2019-07-03 15:28:00.162101", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/engine", "rc": 0, "start": "2019-07-03 15:27:48.195923", "stderr": "", "stderr_lines": [], "stdout": "11.9508", "stdout_lines": ["11.9508"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-1.hci.com -> ov-node-1.hci.com] (item=11.5604) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.574648", "end": "2019-07-03 15:28:14.926805", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/data", "rc": 0, "start": "2019-07-03 15:28:03.352157", "stderr": "", "stderr_lines": [], "stdout": "11.5604", "stdout_lines": ["11.5604"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-1.hci.com -> ov-node-1.hci.com] (item=10.9126) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:10.927547", "end": "2019-07-03 15:28:29.053149", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/vmstore", "rc": 0, "start": "2019-07-03 15:28:18.125602", "stderr": "", "stderr_lines": [], "stdout": "10.9126", "stdout_lines": ["10.9126"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-3.hci.com -> ov-node-1.hci.com] (item=12.7177) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:12.805771", "end": "2019-07-03 15:28:01.029631", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/engine", "rc": 0, "start": "2019-07-03 15:27:48.223860", "stderr": "", "stderr_lines": [], "stdout": "12.7177", "stdout_lines": ["12.7177"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-3.hci.com -> ov-node-1.hci.com] (item=11.8554) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.883952", "end": "2019-07-03 15:28:15.810562", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/data", "rc": 0, "start": "2019-07-03 15:28:03.926610", "stderr": "", "stderr_lines": [], "stdout": "11.8554", "stdout_lines": ["11.8554"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-3.hci.com -> ov-node-1.hci.com] (item=11.6409) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.679377", "end": "2019-07-03 15:28:30.376413", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/vmstore", "rc": 0, "start": "2019-07-03 15:28:18.697036", "stderr": "", "stderr_lines": [], "stdout": "11.6409", "stdout_lines": ["11.6409"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-2.hci.com -> ov-node-1.hci.com] (item=12.607) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:12.699951", "end": "2019-07-03 15:28:00.918459", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/engine", "rc": 0, "start": "2019-07-03 15:27:48.218508", "stderr": "", "stderr_lines": [], "stdout": "12.607", "stdout_lines": ["12.607"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-2.hci.com -> ov-node-1.hci.com] (item=11.9233) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.961081", "end": "2019-07-03 15:28:15.837654", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/data", "rc": 0, "start": "2019-07-03 15:28:03.876573", "stderr": "", "stderr_lines": [], "stdout": "11.9233", "stdout_lines": ["11.9233"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > failed: [ov-node-2.hci.com -> ov-node-1.hci.com] (item=11.5126) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.556528", "end": "2019-07-03 15:28:30.520190", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/vmstore", "rc": 0, "start": "2019-07-03 15:28:18.963662", "stderr": "", "stderr_lines": [], "stdout": "11.5126", "stdout_lines": ["11.5126"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} > ________________________________________________________________________________________ > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/4EBXRAJMQ75TP…

1 0

Re: Hosted Engine Deploy - Error at the end... [NFS ?]
by Strahil 03 Jul '19

03 Jul '19

Have you checked if the permissions are 36:36 on the NFS side ? Beet Regards, Strahil NikolovOn Jul 3, 2019 12:04, csi-laser(a)cisco.com wrote: > > Hi, > While Trying to Deploy Hosted Engine, I'm stuck on Stage 4. Here is the error : > > [ INFO ] TASK [ovirt.hosted_engine_setup : Fetch Datacenter name] > [ INFO ] ok: [localhost] > [ INFO ] TASK [ovirt.hosted_engine_setup : Add NFS storage domain] > [ ERROR ] Verify permission settings on the specified storage path.]". HTTP response code is 400. > [ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "Fault reason is \"Operation Failed\". Fault detail is \"[Permission settings on the specified path do not allow access to the storage.\nVerify permission settings on the specified storage path.]\". HTTP response code is 400."} > > But, it's very strange, because, when I'm trying to mount this NFS share manually, It's working.... > So what am I doing wrong here ? > > Here is the "Storage Connection" - 8.45.119.16:/ovirt_engine > Mount option is blanked > NFS Version is "v3" > > Thanks in advance ! > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/4DPEX6M5PH7Y3…

1 0

Using a synology as an nfs storage
by Andy Michielsen 03 Jul '19

03 Jul '19

Hello, I'm setting up a 3 node cluster with the ovirtnode iso and a seperate server with the engine on and a synology for nfs storage. I have done my configuration and I'm able to mount the share manually on the node with a command. Also on the server with the engine on I can mount it manually. But when I want to do it through the webinterface to add a data domain it say the permissions are wrong. Any idea's on how to figure this out ? Kind regards.

7 11

Disk latency is very high, time taken to copy 1M file is > 10s
by PS Kazi 03 Jul '19

03 Jul '19

hi, I am using HDD : Toshiba 7200 RPM, Data transfer Rate 150MB/s, Interface 6Gb/s. But Hyper-converged configuration stopped with error msg: Disk latency is very high, time taken to copy 1M file is > 10s Please help me to stop this error. ________________________________________________________________________________________ TASK [gluster.features/roles/gluster_hci : Check if time taken to copy 1M file (512B chunks) is < 10s] *** failed: [ov-node-1.hci.com -> ov-node-1.hci.com] (item=11.9508) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.966178", "end": "2019-07-03 15:28:00.162101", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/engine", "rc": 0, "start": "2019-07-03 15:27:48.195923", "stderr": "", "stderr_lines": [], "stdout": "11.9508", "stdout_lines": ["11.9508"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-1.hci.com -> ov-node-1.hci.com] (item=11.5604) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.574648", "end": "2019-07-03 15:28:14.926805", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/data", "rc": 0, "start": "2019-07-03 15:28:03.352157", "stderr": "", "stderr_lines": [], "stdout": "11.5604", "stdout_lines": ["11.5604"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-1.hci.com -> ov-node-1.hci.com] (item=10.9126) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:10.927547", "end": "2019-07-03 15:28:29.053149", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/vmstore", "rc": 0, "start": "2019-07-03 15:28:18.125602", "stderr": "", "stderr_lines": [], "stdout": "10.9126", "stdout_lines": ["10.9126"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-3.hci.com -> ov-node-1.hci.com] (item=12.7177) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:12.805771", "end": "2019-07-03 15:28:01.029631", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/engine", "rc": 0, "start": "2019-07-03 15:27:48.223860", "stderr": "", "stderr_lines": [], "stdout": "12.7177", "stdout_lines": ["12.7177"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-3.hci.com -> ov-node-1.hci.com] (item=11.8554) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.883952", "end": "2019-07-03 15:28:15.810562", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/data", "rc": 0, "start": "2019-07-03 15:28:03.926610", "stderr": "", "stderr_lines": [], "stdout": "11.8554", "stdout_lines": ["11.8554"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-3.hci.com -> ov-node-1.hci.com] (item=11.6409) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.679377", "end": "2019-07-03 15:28:30.376413", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/vmstore", "rc": 0, "start": "2019-07-03 15:28:18.697036", "stderr": "", "stderr_lines": [], "stdout": "11.6409", "stdout_lines": ["11.6409"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-2.hci.com -> ov-node-1.hci.com] (item=12.607) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:12.699951", "end": "2019-07-03 15:28:00.918459", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/engine/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/engine", "rc": 0, "start": "2019-07-03 15:27:48.218508", "stderr": "", "stderr_lines": [], "stdout": "12.607", "stdout_lines": ["12.607"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-2.hci.com -> ov-node-1.hci.com] (item=11.9233) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.961081", "end": "2019-07-03 15:28:15.837654", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/data/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/data", "rc": 0, "start": "2019-07-03 15:28:03.876573", "stderr": "", "stderr_lines": [], "stdout": "11.9233", "stdout_lines": ["11.9233"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} failed: [ov-node-2.hci.com -> ov-node-1.hci.com] (item=11.5126) => {"ansible_loop_var": "item", "changed": false, "item": {"ansible_loop_var": "item", "changed": true, "cmd": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "delta": "0:00:11.556528", "end": "2019-07-03 15:28:30.520190", "failed": false, "invocation": {"module_args": {"_raw_params": "dd if=/dev/zero of=/mnt/tmp/vmstore/small.file bs=512 count=2050 oflag=direct 2>&1 |\n awk '/copied/{print $(NF-3)}'\n", "_uses_shell": true, "argv": null, "chdir": null, "creates": null, "executable": null, "removes": null, "stdin": null, "stdin_add_newline": true, "strip_empty_ends": true, "warn": true}}, "item": "/mnt/tmp/vmstore", "rc": 0, "start": "2019-07-03 15:28:18.963662", "stderr": "", "stderr_lines": [], "stdout": "11.5126", "stdout_lines": ["11.5126"]}, "msg": "Disk latency is very high, time taken to copy 1M file is > 10s"} ________________________________________________________________________________________

2 2

Hosted Engine Deploy - Error at the end... [NFS ?]
by csi-laser＠cisco.com 03 Jul '19

03 Jul '19

Hi, While Trying to Deploy Hosted Engine, I'm stuck on Stage 4. Here is the error : [ INFO ] TASK [ovirt.hosted_engine_setup : Fetch Datacenter name] [ INFO ] ok: [localhost] [ INFO ] TASK [ovirt.hosted_engine_setup : Add NFS storage domain] [ ERROR ] Verify permission settings on the specified storage path.]". HTTP response code is 400. [ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "Fault reason is \"Operation Failed\". Fault detail is \"[Permission settings on the specified path do not allow access to the storage.\nVerify permission settings on the specified storage path.]\". HTTP response code is 400."} But, it's very strange, because, when I'm trying to mount this NFS share manually, It's working.... So what am I doing wrong here ? Here is the "Storage Connection" - 8.45.119.16:/ovirt_engine Mount option is blanked NFS Version is "v3" Thanks in advance !

3 6

network performance issues
by Guy Brodny 02 Jul '19

02 Jul '19

Hello. we have installed Ovirt on HPE ProLiant XL270d Gen10. The server is installed with 2 * Intel(R) Xeon(R) Gold 6154 CPU @ 3.00GHz, 1.5T Ram, 23T Local SSD, 4 Nvidia V100 32GB GPU and 2* Mellanox Technologies MT27800 Family [ConnectX-5] The Mellanox card are 2 100Gbit DualPort each connected with a single 100Gbit port to a Mellanox 100Gbit switch which has access to a 16GByte storage server. MTU is set to 9000 for jumbo packets. Running our application on a VM created on top of the server is having lower network performance vs the host. I tried both normal ovirt network driver, using Virtual Function and PCI-passthrough moving one of the Mellanox card directly to the VM but i never get the same result as on the host. I also tried allocating the numa bush directly to the VM but it doesnt improve the results. Im testing using FIO to perform sequential reads from the storage, this is the command we run both on the host and the VM. sqream@host-3-171 /media/StorONE1/tpch10t_for_4.0/logs/192.168.3.171_5000 $ fio --randrepeat=1 --ioengine=sync --direct=1 --gtod_reduce=1 --name=test --filename=/media/StorONE3/t1e1s1111t221www22.file --bs=2m --iodepth=24 --size=25G --numjobs=14 --readwrite=read --rwmixread=100 Run status group 0 (all jobs): READ: bw=3919MiB/s (4109MB/s), 280MiB/s-314MiB/s (294MB/s-329MB/s), io=350GiB (376GB), run=81630-91459msec Before starting Ovirt i measured 7.5GB/sec on the host running the same FIO command. are there any optimization i should perform to make sure the vguest i getting the best possible network performance, im mostly stressed about GPFS performance as this is our main filesystem. On the same time running the test on another host not running Ovirt i can still get the 7.9GB/sec. appreciate any comments or suggestions. Kind Regards, *Guy Brodny* Cloud Architecture & DevOps Manager | SQream M: +972-54-2279528 sqream.com <http://www.sqream.com/> | Linkedin <https://www.linkedin.com/company/sqream_/?originalSubdomain=il>| Twitter <https://twitter.com/SQreamTech?ref_src=twsrc%5Egoogle%7Ctwcamp%5Eserp%7Ctwg…>

1 0

is it possible to convert exsi vm into ovirt vm
by Crazy Ayansh 02 Jul '19

02 Jul '19

Hi, How we can convert exsi vms into ovirt vm without vcenter. Thanks Shashank

3 3

oVirt node 4.3.4 stable can't deploy hosted engine to iscsi target all available LUNs used
by Mitja Pirih 02 Jul '19

02 Jul '19

Hi, I am new to oVirt, coming from XenServer platform, so please be patient with me. After a successful install of latest stable oVirt node (ovirt-node-ng-installer-4.3.4-2019061016.el7.iso) I am having troubles deploying hosted engine to an iscsi target over Cockpit. I have a couple of iscsi targets available on two different storage platforms (Synology DS418, Lenovo DE2000H). After retrieving iscsi Target list all LUNs get automatically "connected" by "Target list scan" and shown as used on LUNs list. I can reproduce this every single time. On storage system I can also see, that all LUNs get connected by the initial scan. As a result I an unable to continue the deployment as there are no LUNs available. Is this a normal behavior? What would you suggest me to do? Thanks.

3 3

Adding a custom fence agent on 4.3.4
by Matteo 02 Jul '19

02 Jul '19

Hi, I'm trying to add a custom fence agent for my test deployment on hetzner. Have written a small fence_hetzner_robot script which works ok from cli and installed on every ovirt node. Then added with engine_config in this way: # engine-config -s CustomVdsFenceType="hetzner_robot" But does not show up in fence agents list under host pm configuration. I'm missing something? thanks! Matteo PS: Also tried to set up an empty param mapping, just to test # engine-config -s CustomVdsFenceOptionMapping="hetzner_robot:" but still nothing.

1 1

SPICE and VNC native
by kim.kargaard＠noroff.no 02 Jul '19

02 Jul '19

Hi, We are running ovirt 4.3. The engine is on a bare metal machine and the hosts are running on Centos 7. When installing the engine, I set it to be the webproxy. When I create a new vm, I select both SPICE+VNC. When clicking on the console I only have the option for SPICE native, not for the HTML option. For VNC I have both options and the HTML option can be selected and works. But, this is also the only option that works. VNC Native as well as SPICE Native do not work. I have tried using both remote viewer on Mac and a VNC client on a Windows machine and neither will actually open the VM. I would really also like the SPICE HTML option to exist, but it does not. The enable SPICE proxy in the Console selection is greyed out. When I open in remoteviewer (Mac) I get Unable to connect to the graphic server. Any suggestions? Kim

2 3

it seems vgpu state be mistack freed when operating(start and stop) vm at the same time
by weizhengya16＠gmail.com 02 Jul '19

02 Jul '19

We using ovirt in production environment with each virtual machine with a vGpu。but serveral days later, I find several phisical server has been crash and automatic reboot。And I also found some vGpu exist with no virtual machine using. So it makes virtual machine start fail because of lacking resource.I must enter the vgpu directory and using "echo "1" >remove" to free this vGpu。With ceaselessly stop and start, the probability of its occurrence is approximately 0.1%-1%

1 0

Failed on HE-Storage migration
by Christoph Köhler 02 Jul '19

02 Jul '19

Hello, we tried to migrate the hosted engine to a new storage but we ran into an error - in any attempt the same. What we did is: ° Version 4.3.4.3-1.el7 ° in the engine vm: systemctl stop ovirt-engine ° took backup with scope=all ° hosted-engine --set-maintenance --mode=global ° hosted-engine --vm-shutdown ° on a new host (not in the inventory of engineDB): hosted-engine ---deploy --restore-from-file=backup-file It ran fine until: // ERROR ] fatal: [localhost -> newhost]: FAILED! => {"changed": true, "cmd": ["engine-setup", "--accept-defaults", "--config-append=/root/ovirt-engine-answers", "--offline"], "delta": "0:00:00.801074", "end": "2019-06-27 12:13:49.157140", "msg": "non-zero return code", "rc": 1, "start": "2019-06-27 12:13:48.356066", "stderr": "", "stderr_lines": [], "stdout": "[ INFO ] Stage: Initializing\n[ INFO ] Stage: Environment setup\n Configuration files: ['/etc/ovirt-engine-setup.conf.d/10-packaging-jboss.conf', '/etc/ovirt-engine-setup.conf.d/10-packaging.conf', '/etc/ovirt-engine-setup.conf.d/20-setup-ovirt-post.conf', '/root/ovirt-engine-answers']\n Log file: /var/log/ovirt-engine/setup/ovirt-engine-setup-20190627121348-48b6rw.log\n Version: otopi-1.8.2 (otopi-1.8.2-1.el7)\n[ ERROR ] Failed to execute stage 'Environment setup': Cannot connect to ovirt cinderlib database using existing credentials: ovirt_cinderlib@localhost:5432\n[ INFO ] Stage: Clean up\n Log file is located at /var/log/ovirt-engine/setup/ovirt-engine-setup-20190627121348-48b6rw.log\n[ INFO ] Generating answer file '/var/lib/ovirt-engine/setup/answers/20190627121349-setup.conf'\n[ INFO ] Stage: Pre-termination\n[ INFO ] Stage: Termination\n[ ERROR ] Execution of setup failed", "stdout_lines": ["[ INFO ] Stage: Initializing", "[ INFO ] Stage: Environment setup", " Configuration files: ['/etc/ovirt-engine-setup.conf.d/10-packaging-jboss.conf', '/etc/ovirt-engine-setup.conf.d/10-packaging.conf', '/etc/ovirt-engine-setup.conf.d/20-setup-ovirt-post.conf', '/root/ovirt-engine-answers']", " Log file: /var/log/ovirt-engine/setup/ovirt-engine-setup-20190627121348-48b6rw.log", " Version: otopi-1.8.2 (otopi-1.8.2-1.el7)", "[ ERROR ] Failed to execute stage 'Environment setup': Cannot connect to ovirt cinderlib database using existing credentials: ovirt_cinderlib@localhost:5432", "[ INFO ] Stage: Clean up", " Log file is located at /var/log/ovirt-engine/setup/ovirt-engine-setup-20190627121348-48b6rw.log", "[ INFO ] Generating answer file '/var/lib/ovirt-engine/setup/answers/20190627121349-setup.conf'", "[ INFO ] Stage: Pre-termination", "[ INFO ] Stage: Termination", "[ ERROR ] Execution of setup failed"]} // The user and password hashes are okay and the same on old_engine and restore_file. Any ideas? regards, Chris

3 4

Re: [ovirt-devel] USB on host support?
by Nir Soffer 02 Jul '19

02 Jul '19

On Sat, Jun 29, 2019 at 11:57 PM Hetz Ben Hamo <hetz(a)hetz.biz> wrote: > One of the requirements is USB host support (which will be on the nodes, > not on the desktops). I haven't found any way to connect USB to a VM other > then through SPICE, but this method won't help as these dongles won't be on > desktops. > > Is this in the road map of oVirt? > Did you try Compute > Virtual machines > vm-name > Host devices? Nir

3 2

[ANN] Incubating terraform-provider-ovirt
by Roy Golan 01 Jul '19

01 Jul '19

Hi all, Happy to announce the incubation of a terraform provider[1] for oVirt which is the the result of a community effort started by ESM-MSC institute [2] and then picked up by @imjoey [3] which is now the main maintainer of the project. Terraform with an ovirt provider makes it easy to declaratively create virtualized environments. One usage we will make of it is to create an installer for OKD 4 [4] which will lay an OKD cluster on top of oVirt resources. [1] https://github.com/oVirt/terraform-provider-ovirt [2] https://github.com/EMSL-MSC/terraform-provider-ovirt [3] https://github.com/imjoey/terraform-provider-ovirt [4] https://github.com/openshift/installer Roy

2 1

How to clear this error? Can't get in to the administration or vm portals
by mrobbins＠radiax.com 01 Jul '19

01 Jul '19

relevant logs taken from Engine server /var/log/ovirt-engine/server.log: 2019-06-28 11:43:26,971-07 INFO [org.ovirt.engine.core.vdsbroker.IsVmDuringInitiatingVDSCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-73) [37ac641] START, IsVmDuringInitiatingVDSCommand( IsVmDuringInitiatingVDSCommandParameters:{vmId='ebe1a8b0-235b-4af0-96a8-e04269cd7a8e'}), log id: 4a014d00 2019-06-28 11:43:26,995-07 ERROR [org.ovirt.engine.core.bll.HaAutoStartVmsRunner] (EE-ManagedThreadFactory-engineScheduled-Thread-73) [37ac641] Exception in startFailedAutoStartVms: JsonMappingException: Can not deserialize instance of java.util.LinkedHashMap out of START_ARRAY token 2019-06-28 11:43:28,041-07 INFO [org.ovirt.engine.core.vdsbroker.IsVmDuringInitiatingVDSCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-91) [7a301f69] START, IsVmDuringInitiatingVDSCommand( IsVmDuringInitiatingVDSCommandParameters:{vmId='ebe1a8b0-235b-4af0-96a8-e04269cd7a8e'}), log id: 444c67e7 2019-06-28 11:43:28,065-07 ERROR [org.ovirt.engine.core.bll.HaAutoStartVmsRunner] (EE-ManagedThreadFactory-engineScheduled-Thread-91) [7a301f69] Exception in startFailedAutoStartVms: JsonMappingException: Can not deserialize instance of java.util.LinkedHashMap out of START_ARRAY token 2019-06-28 11:43:29,122-07 INFO [org.ovirt.engine.core.vdsbroker.IsVmDuringInitiatingVDSCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-31) [4a698430] START, IsVmDuringInitiatingVDSCommand( IsVmDuringInitiatingVDSCommandParameters:{vmId='ebe1a8b0-235b-4af0-96a8-e04269cd7a8e'}), log id: 7626e5f1 2019-06-28 11:43:29,146-07 ERROR [org.ovirt.engine.core.bll.HaAutoStartVmsRunner] (EE-ManagedThreadFactory-engineScheduled-Thread-31) [4a698430] Exception in startFailedAutoStartVms: JsonMappingException: Can not deserialize instance of java.util.LinkedHashMap out of START_ARRAY token 2019-06-28 11:43:30,198-07 INFO [org.ovirt.engine.core.vdsbroker.IsVmDuringInitiatingVDSCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-90) [fb1b396] START, IsVmDuringInitiatingVDSCommand( IsVmDuringInitiatingVDSCommandParameters:{vmId='ebe1a8b0-235b-4af0-96a8-e04269cd7a8e'}), log id: 615cc6a5 2019-06-28 11:43:30,226-07 ERROR [org.ovirt.engine.core.bll.HaAutoStartVmsRunner] (EE-ManagedThreadFactory-engineScheduled-Thread-90) [fb1b396] Exception in startFailedAutoStartVms: JsonMappingException: Can not deserialize instance of java.util.LinkedHashMap out of START_ARRAY token 2019-06-28 11:43:31,284-07 INFO [org.ovirt.engine.core.vdsbroker.IsVmDuringInitiatingVDSCommand] (EE-ManagedThreadFactory-engineScheduled-Thread-5) [4e0f2d55] START, IsVmDuringInitiatingVDSCommand( IsVmDuringInitiatingVDSCommandParameters:{vmId='ebe1a8b0-235b-4af0-96a8-e04269cd7a8e'}), log id: 22ac8448 2019-06-28 11:43:31,312-07 ERROR [org.ovirt.engine.core.bll.HaAutoStartVmsRunner] (EE-ManagedThreadFactory-engineScheduled-Thread-5) [4e0f2d55] Exception in startFailedAutoStartVms: JsonMappingException: Can not deserialize instance of java.util.LinkedHashMap out of START_ARRAY token at [Source: java.io.StringReader@33492c7c; line: 633, column: 6] (through reference chain: org.ovirt.engine.core.common.action.VmManagementParametersBase["watchdog"]->org.ovirt.engine.core.common.businessentities.VmWatchdog["specParams"]) Error when attempting to login to administration or vm portal: org.apache.commons.lang.SerializationException: org.codehaus.jackson.map.JsonMappingException: Can not deserialize instance of java.util.LinkedHashMap out of START_ARRAY token at [Source: java.io.StringReader@11ef98d5; line: 633, column: 6] (through reference chain: org.ovirt.engine.core.common.action.VmManagementParametersBase["watchdog"]->org.ovirt.engine.core.common.businessentities.VmWatchdog["specParams"]) I've restarted the engine host. I've restarted the engine service. I've checked for zombie tasks with the db utils - none found. Engine is hosted in a HA environment with 2 iron boxes, I have rebooted the hosts that engine is running on. I have migrated hostedengine to both hosts to see if there's an issue perhaps with one of the hosts. No resolution of issue. Been searching for various aspects of the logs to try & get an answer (for quite a few days this issue started some time ago and is in our test environment), all seem to lead to dead ends. hosted-engine --vm-status --== Host 1 (id: 1) status ==-- conf_on_shared_storage : True Status up-to-date : True Hostname : hostname Host ID : 1 Engine status : {"reason": "vm not running on this host", "health": "bad", "vm": "down", "detail": "unknown"} Score : 3400 stopped : False Local maintenance : False crc32 : a3c24020 local_conf_timestamp : 425 Host timestamp : 425 Extra metadata (valid at timestamp): metadata_parse_version=1 metadata_feature_version=1 timestamp=425 (Fri Jun 28 14:06:44 2019) host-id=1 score=3400 vm_conf_refresh_time=425 (Fri Jun 28 14:06:45 2019) conf_on_shared_storage=True maintenance=False state=EngineDown stopped=False --== Host 2 (id: 2) status ==-- conf_on_shared_storage : True Status up-to-date : True Hostname : hostname Host ID : 2 Engine status : {"health": "good", "vm": "up", "detail": "Up"} Score : 3400 stopped : False Local maintenance : False crc32 : e9a6ca22 local_conf_timestamp : 952 Host timestamp : 952 Extra metadata (valid at timestamp): metadata_parse_version=1 metadata_feature_version=1 timestamp=952 (Fri Jun 28 14:06:50 2019) host-id=2 score=3400 vm_conf_refresh_time=952 (Fri Jun 28 14:06:50 2019) conf_on_shared_storage=True maintenance=False state=EngineUp stopped=False Last thing I did before this error showed up was created about 10 servers from a template. There were various lease errors for the servers but they came up and seemed functional. Clearly the issue is here: "Exception in startFailedAutoStartVms" in the "START_ARRAY token" but I can't find anything as of yet that says if you see this - do x,y,z. Learning oVirt so my apologies if this is a 101 question.

1 0

Re: SPICE and VNC native
by Strahil 01 Jul '19

01 Jul '19

The graphics server is the actual host. Can you directly access SPICE/VNC port from your workstation? Best Regards, Strahil NikolovOn Jul 1, 2019 13:31, kim.kargaard(a)noroff.no wrote: > > Hi, > > We are running ovirt 4.3. The engine is on a bare metal machine and the hosts are running on Centos 7. When installing the engine, I set it to be the webproxy. When I create a new vm, I select both SPICE+VNC. When clicking on the console I only have the option for SPICE native, not for the HTML option. For VNC I have both options and the HTML option can be selected and works. But, this is also the only option that works. VNC Native as well as SPICE Native do not work. I have tried using both remote viewer on Mac and a VNC client on a Windows machine and neither will actually open the VM. I would really also like the SPICE HTML option to exist, but it does not. The enable SPICE proxy in the Console selection is greyed out. > > When I open in remoteviewer (Mac) I get Unable to connect to the graphic server. > > Any suggestions? > > Kim > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/PDH2UJKZC2XEO…

3 2

Mix CPU
by suporte＠logicworks.pt 01 Jul '19

01 Jul '19

Hello, Can we mix an Intel cpu with an AMD cpu in the same cluster? Thanks -- Jose Ferradeira http://www.logicworks.pt

5 5

Re: USB Passtrough device problem
by Strahil 01 Jul '19

01 Jul '19

You can attach the usb to an oVirt node and check the module in use there. Then you can try patthrough the device and check the module in use on the VM (if it's linux) or install the driver (if Windows). Best Regards, Strahil NikolovOn Jun 28, 2019 21:11, Juan Pablo Lorier <jplorier(a)gmail.com> wrote: > > thanks anyway. I'm trying to figure out how to deal with this. > > Regards > > El 26/6/19 a las 16:45, Strahil escribió: > > Slow motion... This sounds like bad driver or an unoptimized one. > > Sadly I have no more ideas how to overcome this. > > Best Rregards, > Strahil Nikolov > > On Jun 25, 2019 20:07, jplorier(a)gmail.com wrote: >> >> Hi Strahil >> >> Sorry for the late reply but google sent ovirt mails to spam. I have tried and thought I get audio, it sounds like its played at an incorrect bitrate (I recorded audio ant soundls like slow motion audio). >> Is there any other way to present the usb device than throught console usb emulation? >> Regards >>

2 1

Re: hosted engine not getting up
by Crazy Ayansh 01 Jul '19

01 Jul '19

Hi Simon, It seems to be a memory issue but why it's not showing correct memory there i mean in hosted engine i have given below memory : [image: image.png] whereas it is showing on virsh -r *** command is bit lesser why ? [image: image.png] why both are different ? On Mon, Jul 1, 2019 at 12:31 PM Crazy Ayansh <shashank123rastogi(a)gmail.com> wrote: > Hi Simon, It seems to be a memory issue but why it's not showing correct > memory there i mean in hosted engine i have given below memory : > [image: image.png] > > whereas it is showing on virsh -r *** command is bit lesser why ? > [image: image.png] > > why both are different ? > > Thanks > > > > On Fri, Jun 28, 2019 at 7:11 PM Simone Tiraboschi <stirabos(a)redhat.com> > wrote: > >> Can you please check how much memory it got in the output of virsh -r >> dumpxml HostedEngine ? >> >> >> On Fri, Jun 28, 2019 at 3:27 PM Crazy Ayansh < >> shashank123rastogi(a)gmail.com> wrote: >> >>> Hi Team, >>> >>> Today i rebooted my hosted engine and found it was not getting up. After >>> connecting through remote viewer i found the error "error:cannot allocate >>> kernel buffer" and i am not able to start hosted engine.any suggestions ? >>> >>> _______________________________________________ >>> Users mailing list -- users(a)ovirt.org >>> To unsubscribe send an email to users-leave(a)ovirt.org >>> Privacy Statement: https://www.ovirt.org/site/privacy-policy/ >>> oVirt Code of Conduct: >>> https://www.ovirt.org/community/about/community-guidelines/ >>> List Archives: >>> https://lists.ovirt.org/archives/list/users@ovirt.org/message/MTDRNK2DZVW4U… >>> >> >> >> -- >> >> Simone Tiraboschi >> >> He / Him / His >> >> Principal Software Engineer >> >> Red Hat <https://www.redhat.com/> >> >> stirabos(a)redhat.com >> @redhatjobs <https://twitter.com/redhatjobs> redhatjobs >> <https://www.facebook.com/redhatjobs> @redhatjobs >> <https://instagram.com/redhatjobs> >> <https://red.ht/sig> >> <https://redhat.com/summit> >> >

2 7

Re: Mix CPU
by Strahil 01 Jul '19

01 Jul '19

No. Keep the hosts with different Brand CPU in separate clusters. For example, I have 2 gluster Bricks with AMD (default cluster) and an Intel-based arbiter (Intel cluster). Best Regards, Strahil NikolovOn Jul 1, 2019 14:39, suporte(a)logicworks.pt wrote: > > Hello, > > Can we mix an Intel cpu with an AMD cpu in the same cluster? > > Thanks > > -- > ________________________________ > Jose Ferradeira > http://www.logicworks.pt

1 0

Re: Proper way to upgrade hosts OS?
by Strahil 01 Jul '19

01 Jul '19

I'm using CentOS7 and no deps were broken. Just follow the following: https://www.ovirt.org/documentation/upgrade-guide/chap-Upgrading_from_4.1_t… Best Regards, Strahil NikolovOn Jul 1, 2019 10:30, Nicolas Ecarnot <nicolas(a)ecarnot.net> wrote: > > Le 26/06/2019 à 12:34, Nicolas Ecarnot a écrit : > > Hello, > > > > We're not using nodes but CentOS 7.x hosts. > > Do you know if some documentation has been written about the proper way > > to upgrade the operating system of the hosts, and especially how to > > prevent breaking dependencies or cause versions flaws? > > > > Thank you. > > > > Hello, > > As no answer came, may anyone just tell me if there's any chance to > break something? > > Thank you. > > -- > Nicolas ECARNOT > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/GZYVUCMBIZIZO…

1 0

hosted engine not getting up
by Crazy Ayansh 01 Jul '19

01 Jul '19

Hi Team, Today i rebooted my hosted engine and found it was not getting up. After connecting through remote viewer i found the error "error:cannot allocate kernel buffer" and i am not able to start hosted engine.any suggestions ?

3 3

Ovirt Hyperconverged Cluster
by raffaele＠stefanile.com 01 Jul '19

01 Jul '19

Hi all, I have configured a 3 nodes cluster with an Hyperconverged gluster. I have used 2 network interface bonded with one VLAN for the mgmt and an other one for the storage. When I use cockpit to deploy the hosted engine I receive this error. [ ERROR ] fatal: [localhost]: FAILED! => {"changed": false, "msg": "The host has been set in non_operational status, please check engine logs, fix accordingly and re-deploy.\n"} The ovirt version is 4.3 Someone have a similar problem?

5 7

Proper way to upgrade hosts OS?
by Nicolas Ecarnot 01 Jul '19

01 Jul '19

Hello, We're not using nodes but CentOS 7.x hosts. Do you know if some documentation has been written about the proper way to upgrade the operating system of the hosts, and especially how to prevent breaking dependencies or cause versions flaws? Thank you. -- Nicolas ECARNOT

2 2