- Users - oVirt List Archives

HCI Deployment oVirt 4.5
by Clint Boggio 29 Jun '22

29 Jun '22

Hello oVirt Team I'm in the process of deploying a three-node oVirt hyperconverged platform and from the cockpit interface of the deployment node I keep running into the same error. The system finishes the gluster deployment phase (sometimes) and then prompts to continue with the hosted engine deployment but then fails immediately complaining about the naming convention of my network interfaces. My network interfaces are 802.3ad bonds configured during the installation process of each node using "bondx" naming convention consistent across all three nodes. Any wisdom or pointers would be appreciated.

4 7

Can't start VM because host has insufficient amount of CPU cores
by Ramon Clematide 29 Jun '22

29 Jun '22

Hi I just upgraded my oVirt installation from 4.4.10 to 4.5.1.2. The upgrade went through without any errors and most things seem to work but i have one critical problem now. Somehow it does not evaluate the correct number of CPU available on the hypervisor and blocks the start of a VM (except for the engine). The problem I only have on the hypervisor which has the engine deployed. I have three hypervisors, but only one has the engine installed. This hypervisor is also in a seperate cluster. After the upgrade, on the hypervisor which has the engine installed, I can't start a VM via the oVirt Manager. I can start the engine via "hosted-engine --vm-start" but if I try to start any other VM it fails with this Error: https://imgur.com/7lbGb8v -------------------------------------------------------------------------------------------------------- Operation Canceled Error while executing action: Razor: Cannot run VM. There is no host that satisfies current scheduling constraints. See below for details: The host venge did not satisfy internal filter CPU because it has an insufficient amount of CPU cores to run the VM. -------------------------------------------------------------------------------------------------------- I did not change any specs for the VM and even if I reduce the VM to only use 1 core it fails with the error above. This are the specs of my hypervisor, it has 2 cores with 2 threads: https://imgur.com/rbJnqP3 This is the ovirt version installed https://imgur.com/4LLTVFN Does someone know how to fix this? Regards

3 3

Keep showing: ovirt kernel: NFS: __nfs4_reclaim_open_state: Lock reclaim failed!
by Ke Ye 29 Jun '22

29 Jun '22

I have two same systems: 1 standalone engine + 1 node + 1 NFS storage. One system works well, but the other one, when starting a vm, always shows paused due to storage I/O error. Any one help me thanks!!!!

1 0

Re: VM hangs after migration
by John 29 Jun '22

29 Jun '22

I'm seeing this too on oVirt 4.5.1 using CentOS Stream 8 for the hosts. The console is blank, no response to ping and I have to power off the VM and power it back on again to recover it. On 26/06/2022 19:53, Christopher Law wrote: > > I have this exact same issue, did you guys get anywhere with this, or > find the cause? > > It’s difficult to debug because as far as the engine and hosts > involved are concerned it was successful. It’s just the VM stops > responding to pings etc after migration and the console freezes > exactly as described here. > > I’m using oVirt 4.5.1 Cluster 4.7. I’ve even reinstalled oVirt Node on > the problem host still behaves the same. I’ve tried removing all > VirtIO devices from the VM, I’ve tried with lower CPU family profiles, > I’ve tried with different BIOS/UEFI settings. > > In some cases the VM freezes moving away from the problem host as well > which is interesting. > > *From:*Arik Hadas <ahadas(a)redhat.com> > *Sent:* 31 March 2022 15:11 > *To:* Moshe Sheena <msheena(a)redhat.com> > *Cc:* users <users(a)ovirt.org> > *Subject:* [ovirt-users] Re: VM hangs after migration > > Moshe, this sounds similar to what we've seen in your environment, no? > > Did you manage to resolve it? > > On Thu, Mar 31, 2022 at 12:57 PM Giorgio Biacchi <giorgio(a)di.unimi.it> > wrote: > > Hi, > I have a fresh Ovirt installation (4.4.10.7-1.el8 engine and oVirt > Node > 4.4.10) on a Dell VRTX chassis. There are 3 blades, two of them are > identical hardware (PowerEdge M630) and the third is a little newer > (PowerEdge M640). The third has different CPUs, more RAM, and slower > NICs. I also have a bunch of data domains some on the shared PERC > internal storage and others on an external iSCSI storage, all seems > configured correctly and all the hosts are operational. > > I can migrate a VM back and forth from the first two blades > without any > problem, I can migrate a VM to the third blade but when I migrate > a VM > from the third blade to any of the other two the task terminate > successfully, the VM is marked as up on the target host but the VM > hangs, the console is frozen and the VM stops to respond to ping. > > I have no clues about why this is happening and I'm looking for > suggestions about how to debug and hopefully fix this issue. > > Thanks in advance > -- > gb > > PGP Key: http://pgp.mit.edu/ > Primary key fingerprint: C510 0765 943E EBED A4F2 69D3 16CC DC90 > B9CB 0F34 > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/privacy-policy.html > oVirt Code of Conduct: > https://www.ovirt.org/community/about/community-guidelines/ > List Archives: > https://lists.ovirt.org/archives/list/users@ovirt.org/message/HYHAVG3KDHMNV… > > > _______________________________________________ > Users mailing list --users(a)ovirt.org > To unsubscribe send an email tousers-leave(a)ovirt.org > Privacy Statement:https://www.ovirt.org/privacy-policy.html > oVirt Code of Conduct:https://www.ovirt.org/community/about/community-guidelines/ > List Archives:https://lists.ovirt.org/archives/list/users@ovirt.org/message/VUOM… -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

3 2

ovirt node 4.5.1 fails to boot cleanly with selinux-autorelabel-mark.service: Job selinux-autorelabel-mark.service/start failed with result 'dependency'
by p.staniforth＠leedsbeckett.ac.uk 28 Jun '22

28 Jun '22

Hello we have some nodes that don't boot cleanly, CTRL-D or logging into the node allows the system to finish the startup properly. selinux-autorelabel-mark.service: Job selinux-autorelabel-mark.service/start failed with result 'dependency' systemd[1]: Timed out waiting for device dev-disk-by\x2duuid-3839035f\x2db3be\x2d4b8b\x2db711\x2df19bee4785f2.device. systemd[1]: Dependency failed for /gluster_bricks/extra. systemd[1]: Dependency failed for Local File Systems. systemd[1]: Dependency failed for Mark the need to relabel after reboot. systemd[1]: selinux-autorelabel-mark.service: Job selinux-autorelabel-mark.service/start failed with result 'dependency'. systemd[1]: local-fs.target: Job local-fs.target/start failed with result 'dependency'. systemd[1]: local-fs.target: Triggering OnFailure= dependencies. systemd[1]: gluster_bricks-extra.mount: Job gluster_bricks-extra.mount/start failed with result 'dependency'. systemd[1]: dev-disk-by\x2duuid-3839035f\x2db3be\x2d4b8b\x2db711\x2df19bee4785f2.device: Job dev-disk-by\x2duuid-3839035f\x2db3be\x2d4b8b\x2db711\x2df19bee4785f2.device/start failed with result 'timeout'. The other gluster bricks created at install time don't have this problem. Thanks, Paul S.

1 0

Install Ovirt 4.5.1 on Centos Stream 8.6
by moula.badji＠gmail.com 28 Jun '22

28 Jun '22

Hello, I'm trying to install ovirt-engine on centos Stream 8.6 and it's still not possible due to outdated dependencies. ovirt-engine-keycloak ovirt-engine-keycloak-setup mod_auth_openidc Thank's. Moula.

2 2

Regarding oVirt VM Hosting
by Nishith Vyas 27 Jun '22

27 Jun '22

Dear Users, I've initiated this mail communication for the very first time. Recently, I've started using *oVirt-Engine* & *oVirt-Node* in my lab as I want to host a openstack kind of infrastructure hosting environment for my company. Prior to that, I'd like to get information on the below listed statement. ---------------------------------------------------------------------------------- I've created data domain, iso domain & export domain over the NFS. Now, my VM is created by loading CentOS 7.9 ISO from "iso domain" & storing "VM" data on "data domain". Here, I'm just curious to know about the NFS efficiency to manage VMs because the OS boots/loads from remote "NFS Data Domain", not from the local storage (i.e. oVirt-Node) Which is more efficient? NFS or iSCSI for VM Hosting? ----------------------------------------------------------------------------------- Regards, *Nishit**h **N. Vyas* *Ca**l**l:** +91 98**79597301* *https://www.linkedin.com/in/nishithvyas <https://www.linkedin.com/in/nishithvyas>* *Tha**nk** you for not printing this email! Save trees & Go Green!*

1 0

oVirt Survey Summer 2022
by Sandro Bonazzola 27 Jun '22

27 Jun '22

oVirt Survey Summer 2022 As we continue to develop oVirt 4.5, the oVirt community would value insights on your experience with the oVirt project. Please help us to hit the mark by completing this short survey: https://forms.gle/2LxoDKb7njEQwr4f7 . Survey will close on July 29th 2022. Please note the answers to this survey will be publicly accessible. This survey is under oVirt Privacy Policy available at https://ovirt.org/privacy-policy.html . -- Sandro Bonazzola MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV Red Hat EMEA <https://www.redhat.com/> sbonazzo(a)redhat.com <https://www.redhat.com/> *Red Hat respects your work life balance. Therefore there is no need to answer this email out of your office hours.*

1 0

VMs missing following Import of Storage Domain
by simon＠justconnect.ie 27 Jun '22

27 Jun '22

Hi All, I have 2 oVirt 3 node Clusters in 2 Datacenters - effectively 2 independent environements with stretched VLANs for DR purposes. Each volume is geo replicated to the other datacenter. Each volume is a separate Storage Domain. In a DR event the geo-replicated volumes/Storage Domains are imported in the other Datacenter and the VMs imported once it's attached. The issue I am seeing is that some of the VMs are not listed when I click 'VM Import' from the imported Storage Domain. The disks for those missing VMs however, do exist in 'Disk Import' Tab of the imported Storage Domain. Prior to importing the Storage Domain in Site B, all VM disks were migrated to a single Storage Domain in Site A and geo-replication allowed to sync. Kind Regards Simon...

3 7

VM hangs after migration
by Giorgio Biacchi 26 Jun '22

26 Jun '22

Hi, I have a fresh Ovirt installation (4.4.10.7-1.el8 engine and oVirt Node 4.4.10) on a Dell VRTX chassis. There are 3 blades, two of them are identical hardware (PowerEdge M630) and the third is a little newer (PowerEdge M640). The third has different CPUs, more RAM, and slower NICs. I also have a bunch of data domains some on the shared PERC internal storage and others on an external iSCSI storage, all seems configured correctly and all the hosts are operational. I can migrate a VM back and forth from the first two blades without any problem, I can migrate a VM to the third blade but when I migrate a VM from the third blade to any of the other two the task terminate successfully, the VM is marked as up on the target host but the VM hangs, the console is frozen and the VM stops to respond to ping. I have no clues about why this is happening and I'm looking for suggestions about how to debug and hopefully fix this issue. Thanks in advance -- gb PGP Key: http://pgp.mit.edu/ Primary key fingerprint: C510 0765 943E EBED A4F2 69D3 16CC DC90 B9CB 0F34

3 2