- Users - oVirt List Archives

Partition Trouble on oVirt Node
by Matt Simonsen 16 Feb '18

16 Feb '18

Hello all, This may not be oVirt specific (but it may be) so thank you in advance for any assistance. I have a system installed with oVirt Node Next 4.1.9 that was installed to /dev/sda I had a seperate RAID Volume /dev/sdb that should not have been used, but now that the operating system is loaded I'm struggling to get the device partitioned. I've tried mkfs.ext4 on the device and also pvcreate, with the errors below. I've also rebooted a couple times and tried to disable multipathd. Is multipathd even safe to disable on Node Next? Below are the errors I've received, and thank you again for any tips. [root@node1-g6-h3 ~]# mkfs.ext4 /dev/sdb mke2fs 1.42.9 (28-Dec-2013) /dev/sdb is entire device, not just one partition! Proceed anyway? (y,n) y /dev/sdb is apparently in use by the system; will not make a filesystem here! [root@node1-g6-h3 ~]# gdisk GPT fdisk (gdisk) version 0.8.6 Type device filename, or press <Enter> to exit: /dev/sdb Caution: invalid main GPT header, but valid backup; regenerating main header from backup! Caution! After loading partitions, the CRC doesn't check out! Warning! Main partition table CRC mismatch! Loaded backup partition table instead of main partition table! Warning! One or more CRCs don't match. You should repair the disk! Partition table scan: MBR: not present BSD: not present APM: not present GPT: damaged Found invalid MBR and corrupt GPT. What do you want to do? (Using the GPT MAY permit recovery of GPT data.) 1 - Use current GPT 2 - Create blank GPT Your answer: 2 Command (? for help): n Partition number (1-128, default 1): First sector (34-16952264590, default = 2048) or {+-}size{KMGTP}: Last sector (2048-16952264590, default = 16952264590) or {+-}size{KMGTP}: Current type is 'Linux filesystem' Hex code or GUID (L to show codes, Enter = 8300): 8e00 Changed type of partition to 'Linux LVM' Command (? for help): w Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING PARTITIONS!! Do you want to proceed? (Y/N): y OK; writing new GUID partition table (GPT) to /dev/sdb. The operation has completed successfully. [root@node1-g6-h3 ~]# pvcreate /dev/sdb1 Device /dev/sdb1 not found (or ignored by filtering).

3 2

Virtual networks in oVirt 4.2 and MTU 1500
by Dmitry Semenov 15 Feb '18

15 Feb '18

I have a not big cluster on oVirt 4.2. Each node has a bond, that has several vlans in its turn. I use virtual networks OVN (External Provider -> ovirt-provider-ovn). While testing I have noticed that in virtual network MTU must be less 1500, so my question is may I change something in network or in bond in order everything in virtual network works correctly with MTU 1500? Below link with my settings: https://pastebin.com/F7ssCVFa -- Best regards

2 1

hosted-engine deploy 4.2.1 fails when ovirtmgmt is defined on vlan subinterface
by Kuko Armas 15 Feb '18

15 Feb '18

I'm not sure if I should submit a bug report about this, so I ask around here first... I've found a bug that "seems" related but I think it's not (https://bugzilla.redhat.com/show_bug.cgi?id=1523661) This is the problem: - I'm trying to do a clean HE deploy with oVirt 4.2.1 on a clean CentOS 7.4 host - I have a LACP bond (bond0) and I need my management network to be on vlan 1005, si I have created interface bond0.1005 on the host and everything works - I run hosted-engine deploy, and it always fails with [ ERROR ] fatal: [localhost]: FAILED! => {"attempts": 50, "changed": true, "cmd": "ip rule list | grep ovirtmgmt | sed s/\\\\[.*\\\\]\\ //g | awk '{ print $9 }'", "delta": "0:00:00.006473", "end": "2018-02-15 13:57:11.132359", "rc": 0, "start": "2018-02-15 13:57:11.125886", "stderr": "", "stderr_lines": [], "stdout": "", "stdout_lines": []} [ ERROR ] Failed to execute stage 'Closing up': Failed executing ansible-playbook - Looking at the ansible playbook, I see it's trying to look for an ip rule using a custom routing table, but I have no such rule [root@ovirt1 ~]# ip rule 0: from all lookup local 32766: from all lookup main 32767: from all lookup default - I also find that I have no "ovirtmgmt" bridge bridge name bridge id STP enabled interfaces ;vdsmdummy; 8000.000000000000 no virbr0 8000.525400e6ca97 yes virbr0-nic vnet0 - But I haven't found any reference in the ansible playbook to this network creation. - The HE VM gets created and I can connect with SSH, so I tried to find out if the ovirtmgmt network is created via vdsm from the engine - Looking at the engine.log I found this: 2018-02-15 13:49:26,850Z INFO [org.ovirt.engine.core.bll.host.HostConnectivityChecker] (EE-ManagedThreadFactory-engine-Thread-1) [15c7e33a] Engine managed to communicate wi th VDSM agent on host 'ovirt1' with address 'ovirt1' ('06651b32-4ef8-4b5d-ab2d-c38e84c2d790') 2018-02-15 13:49:30,302Z ERROR [org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLogDirector] (EE-ManagedThreadFactory-engine-Thread-1) [15c7e33a] EVENT_ID: VLAN_ID_ MISMATCH_FOR_MANAGEMENT_NETWORK_CONFIGURATION(1,119), Failed to configure management network on host ovirt1. Host ovirt1 has an interface bond0.1005 for the management netwo rk configuration with VLAN-ID (1005), which is different from data-center definition (none). 2018-02-15 13:49:30,302Z ERROR [org.ovirt.engine.core.bll.hostdeploy.InstallVdsInternalCommand] (EE-ManagedThreadFactory-engine-Thread-1) [15c7e33a] Exception: org.ovirt.eng ine.core.bll.network.NetworkConfigurator$NetworkConfiguratorException: Failed to configure management network - So I guess that the engine tried to create the ovirtmgmt bridge on the host via vdsm, but it failed because "Host ovirt1 has an interface bond0.1005 for the management netwo rk configuration with VLAN-ID (1005), which is different from data-center definition (none)" - Of course I haven't had the opportunity to setup the management network's vlan in the datacenter yet, because I'm still trying to deploy the Hosted Engine Is this a supported configuration? Is there a way I can tell the datacenter that the management network is on vlan 1005? Should I file a bug report? Is there a workaround? Salu2! -- Miguel Armas CanaryTek Consultoria y Sistemas SL http://www.canarytek.com/

2 2

Sparsify in 4.2 - where it moved ?
by Andrei V 15 Feb '18

15 Feb '18

Hi ! I can’t locate “Sparsify” disk image command anywhere in oVirt 4.2. Where it have been moved ? Thanks Andrei

3 3

hosted-engine 4.2.1-pre setup on a clean node..
by Thomas Davis 15 Feb '18

15 Feb '18

Is this supported? I have a node, that centos 7.4 minimal is installed on, with an interface setup for an IP address. I've yum installed nothing else except the ovirt-4.2.1-pre rpm, run screen, and then do the 'hosted-engine --deploy' command. It hangs on: [ INFO ] changed: [localhost] [ INFO ] TASK [Get ovirtmgmt route table id] [ ERROR ] fatal: [localhost]: FAILED! => {"attempts": 50, "changed": true, "cmd": "ip rule list | grep ovirtmgmt | sed s/\\\\[.*\\\\]\\ //g | awk '{ print $9 }'", "delta": "0:00:00.004845", "end": "2018-02-02 12:03:30.794860", "rc": 0, "start": "2018-02-02 12:03:30.790015", "stderr": "", "stderr_lines": [], "stdout": "", "stdout_lines": []} [ ERROR ] Failed to execute stage 'Closing up': Failed executing ansible-playbook [ INFO ] Stage: Clean up [ INFO ] Cleaning temporary resources [ INFO ] TASK [Gathering Facts] [ INFO ] ok: [localhost] [ INFO ] TASK [Remove local vm dir] [ INFO ] ok: [localhost] [ INFO ] Generating answer file '/var/lib/ovirt-hosted-engine-setup/answers/answers-20180202120333.conf' [ INFO ] Stage: Pre-termination [ INFO ] Stage: Termination [ ERROR ] Hosted Engine deployment failed: please check the logs for the issue, fix accordingly or re-deploy from scratch. Log file is located at /var/log/ovirt-hosted-engine-setup/ovirt-hosted-engine-setup-20180202115038-r11nh1.log but the VM is up and running, just attached to the 192.168.122.0/24 subnet [root@d8-r13-c2-n1 ~]# ssh root(a)192.168.122.37 root(a)192.168.122.37's password: Last login: Fri Feb 2 11:54:47 2018 from 192.168.122.1 [root@ovirt ~]# systemctl status ovirt-engine ● ovirt-engine.service - oVirt Engine Loaded: loaded (/usr/lib/systemd/system/ovirt-engine.service; enabled; vendor preset: disabled) Active: active (running) since Fri 2018-02-02 11:54:42 PST; 11min ago Main PID: 24724 (ovirt-engine.py) CGroup: /system.slice/ovirt-engine.service ├─24724 /usr/bin/python /usr/share/ovirt-engine/services/ovirt-engine/ovirt-engine.py --redirect-output --systemd=notify start └─24856 ovirt-engine -server -XX:+TieredCompilation -Xms3971M -Xmx3971M -Djava.awt.headless=true -Dsun.rmi.dgc.client.gcInterval=3600000 -Dsun.rmi.dgc.server.gcInterval=3600000 -Djsse... Feb 02 11:54:41 ovirt.crt.nersc.gov systemd[1]: Starting oVirt Engine... Feb 02 11:54:41 ovirt.crt.nersc.gov ovirt-engine.py[24724]: 2018-02-02 11:54:41,767-0800 ovirt-engine: INFO _detectJBossVersion:187 Detecting JBoss version. Running: /usr/lib/jvm/jre/...600000', '- Feb 02 11:54:42 ovirt.crt.nersc.gov ovirt-engine.py[24724]: 2018-02-02 11:54:42,394-0800 ovirt-engine: INFO _detectJBossVersion:207 Return code: 0, | stdout: '[u'WildFly Full 11.0.0....tderr: '[]' Feb 02 11:54:42 ovirt.crt.nersc.gov systemd[1]: Started oVirt Engine. Feb 02 11:55:25 ovirt.crt.nersc.gov python2[25640]: ansible-stat Invoked with checksum_algorithm=sha1 get_checksum=True follow=False path=/usr/share/ovirt-engine/playbooks/roles/ovir...ributes=True Feb 02 11:55:29 ovirt.crt.nersc.gov python2[25698]: ansible-stat Invoked with checksum_algorithm=sha1 get_checksum=True follow=False path=/usr/share/ovirt-engine/playbooks/roles/ovir...ributes=True Feb 02 11:55:30 ovirt.crt.nersc.gov python2[25741]: ansible-stat Invoked with checksum_algorithm=sha1 get_checksum=True follow=False path=/usr/share/ovirt-engine/playbooks/roles/ovir...ributes=True Feb 02 11:55:30 ovirt.crt.nersc.gov python2[25767]: ansible-stat Invoked with checksum_algorithm=sha1 get_checksum=True follow=False path=/usr/share/ovirt-engine/playbooks/roles/ovir...ributes=True Feb 02 11:55:31 ovirt.crt.nersc.gov python2[25795]: ansible-stat Invoked with checksum_algorithm=sha1 get_checksum=True follow=False path=/etc/ovirt-engine-metrics/config.yml get_md5...ributes=True The 'ip rule list' never has an ovirtmgmt rule/table in it.. which means the ansible script loops then dies; vdsmd has never configured the network on the node. [root@d8-r13-c2-n1 ~]# systemctl status vdsmd -l ● vdsmd.service - Virtual Desktop Server Manager Loaded: loaded (/usr/lib/systemd/system/vdsmd.service; enabled; vendor preset: enabled) Active: active (running) since Fri 2018-02-02 11:55:11 PST; 14min ago Main PID: 7654 (vdsmd) CGroup: /system.slice/vdsmd.service └─7654 /usr/bin/python2 /usr/share/vdsm/vdsmd Feb 02 11:55:11 d8-r13-c2-n1 vdsmd_init_common.sh[7551]: vdsm: Running dummybr Feb 02 11:55:11 d8-r13-c2-n1 vdsmd_init_common.sh[7551]: vdsm: Running tune_system Feb 02 11:55:11 d8-r13-c2-n1 vdsmd_init_common.sh[7551]: vdsm: Running test_space Feb 02 11:55:11 d8-r13-c2-n1 vdsmd_init_common.sh[7551]: vdsm: Running test_lo Feb 02 11:55:11 d8-r13-c2-n1 systemd[1]: Started Virtual Desktop Server Manager. Feb 02 11:55:12 d8-r13-c2-n1 vdsm[7654]: WARN File: /var/run/vdsm/trackedInterfaces/vnet0 already removed Feb 02 11:55:12 d8-r13-c2-n1 vdsm[7654]: WARN Not ready yet, ignoring event '|virt|VM_status|ba56a114-efb0-45e0-b2ad-808805ae93e0' args={'ba56a114-efb0-45e0-b2ad-808805ae93e0': {'status': 'Powering up', 'displayInfo': [{'tlsPort': '-1', 'ipAddress': '127.0.0.1', 'type': 'vnc', 'port': '5900'}], 'hash': '5328187475809024041', 'cpuUser': '0.00', 'monitorResponse': '0', 'elapsedTime': '0', 'cpuSys': '0.00', 'vcpuPeriod': 100000L, 'timeOffset': '0', 'clientIp': '', 'pauseCode': 'NOERR', 'vcpuQuota': '-1'}} Feb 02 11:55:13 d8-r13-c2-n1 vdsm[7654]: WARN MOM not available. Feb 02 11:55:13 d8-r13-c2-n1 vdsm[7654]: WARN MOM not available, KSM stats will be missing. Feb 02 11:55:17 d8-r13-c2-n1 vdsm[7654]: WARN ping was deprecated in favor of ping2 and confirmConnectivity Do I need to install a complete ovirt-engine on the node first, bring the node into ovirt, then bring up hosted-engine? I'd like to avoid this and just go straight to hosted-engine setup. thomas

3 7

issue on engine deployment on oVirt node
by Vincent Kwiatkowski 15 Feb '18

15 Feb '18

Hi Folks, I tried a few time to configure a simple oVirt engine on oVirt node. After the fresh install of the node, I connect cockpit and launch the engine setup, then at the end I have the message that I need to connect to the VM with "hosted-engine --console" or via VNC. Via VNC, I can't do nothing, have no prompt using the --console, I have the error: :internal error: character device console0 is not using a PTY What can I do to continue the setup? Thx a lot in advance -- Vincent Kwiatkowski | Production System Engineer |ULLINK | D: + 33 1 44 50 25 45 | T: +1 49 95 30 00 | 23/25 rue de Provence | 75009, Paris | vk(a)ullink.com Please consider the environment before printing this email -- *The information contained in or attached to this email is strictly confidential. If you are not the intended recipient, please notify us immediately by telephone and return the message to us.*

1 0

[ANN] oVirt 4.2.2 First Release Candidate is now available
by Lev Veyde 15 Feb '18

15 Feb '18

The oVirt Project is pleased to announce the availability of the oVirt 4.2.2 First Release Candidate, as of February 15th, 2018 This update is a release candidate of the second in a series of stabilization updates to the 4.2 series. This is pre-release software. This pre-release should not to be used in production. This release is available now for: * Red Hat Enterprise Linux 7.4 or later * CentOS Linux (or similar) 7.4 or later This release supports Hypervisor Hosts running: * Red Hat Enterprise Linux 7.4 or later * CentOS Linux (or similar) 7.4 or later * oVirt Node 4.2 See the release notes [1] for installation / upgrade instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is already available - oVirt Node will be available soon [2] Additional Resources: * Read more about the oVirt 4.2.2 release highlights: http://www.ovirt.org/release/4. <http://www.ovirt.org/release/4.2.2/>2 <http://www.ovirt.org/release/4.2.2/>. <http://www.ovirt.org/release/4.2.2/> 2 <http://www.ovirt.org/release/4.2.2/>/ <http://www.ovirt.org/release/4.2.2/> * Get more oVirt Project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] http://www.ovirt.org/release/4. <http://www.ovirt.org/release/4.2.2/>2 <http://www.ovirt.org/release/4.2.2/>. <http://www.ovirt.org/release/4.2.2/> 2 <http://www.ovirt.org/release/4.2.2/>/ <http://www.ovirt.org/release/4.2.2/> [2] http://resources.ovirt.org/pub/ovirt-4. <http://resources.ovirt.org/pub/ovirt-4.2-pre/iso/>2-pre <http://resources.ovirt.org/pub/ovirt-4.2-pre/iso/>/iso/ <http://resources.ovirt.org/pub/ovirt-4.2-pre/iso/> -- Lev Veyde Software Engineer, RHCE | RHCVA | MCITP Red Hat Israel <https://www.redhat.com> lev(a)redhat.com | lveyde(a)redhat.com <https://red.ht/sig> TRIED. TESTED. TRUSTED. <https://redhat.com/trusted>

1 0

Re: [ovirt-users] Manageiq ovn
by Alona Kaplan 15 Feb '18

15 Feb '18

On Thu, Feb 15, 2018 at 4:03 PM, Aliaksei Nazarenka < aliaksei.nazarenka(a)gmail.com> wrote: > and how i can change network in the created VM? > It is not possible via manageiq. Only via ovirt. > > Sorry for my intrusive questions))) > > 2018-02-15 16:51 GMT+03:00 Aliaksei Nazarenka < > aliaksei.nazarenka(a)gmail.com>: > >> ovirt-provider-ovn-1.2.7-0.20180213232754.gitebd60ad.el7.centos.noarch >> on hosted-engine >> ovirt-provider-ovn-driver-1.2.5-1.el7.centos.noarch on ovirt hosts >> >> 2018-02-15 16:40 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: >> >>> >>> >>> On Thu, Feb 15, 2018 at 3:36 PM, Aliaksei Nazarenka < >>> aliaksei.nazarenka(a)gmail.com> wrote: >>> >>>> when i try to create network router, i see this message: *Unable to >>>> create Network Router "test_router": undefined method `[]' for nil:NilClass* >>>> >>> >>> What ovn-provider version you're using? Can you please attach the ovn >>> provider log ( /var/log/ovirt-provider-ovn.log)? >>> >>> >>>> >>>> 2018-02-15 16:20 GMT+03:00 Aliaksei Nazarenka < >>>> aliaksei.nazarenka(a)gmail.com>: >>>> >>>>> Big Thank you! This work! But... Networks are created, but I do not >>>>> see them in the ovirt manager, but through the ovn-nbctl command, I see all >>>>> the networks. And maybe you can tell me how to assign a VM network from >>>>> Manageiq? >>>>> >>>>> 2018-02-15 15:01 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: >>>>> >>>>>> >>>>>> >>>>>> On Thu, Feb 15, 2018 at 1:54 PM, Aliaksei Nazarenka < >>>>>> aliaksei.nazarenka(a)gmail.com> wrote: >>>>>> >>>>>>> Error - 1 Minute Ago >>>>>>> undefined method `orchestration_stacks' for >>>>>>> #<ManageIQ::Providers::Redhat::InfraManager:0x00000007bf9288> - I >>>>>>> get this message if I try to create a network of overts and then try to >>>>>>> check the status of the network manager. >>>>>>> >>>>>> >>>>>> It is the same bug. >>>>>> You need to apply the fixes in https://github.com/ManageIQ/ma >>>>>> nageiq-providers-ovirt/pull/198/files to make it work. >>>>>> The best option is to upgrade your version. >>>>>> >>>>>> >>>>>>> 2018-02-15 14:28 GMT+03:00 Aliaksei Nazarenka < >>>>>>> aliaksei.nazarenka(a)gmail.com>: >>>>>>> >>>>>>>> I tried to make changes to the file refresher_ovn_provider.yml - >>>>>>>> changed the passwords, corrected the names of the names, but it was not >>>>>>>> successful. >>>>>>>> >>>>>>>> 2018-02-15 14:26 GMT+03:00 Aliaksei Nazarenka < >>>>>>>> aliaksei.nazarenka(a)gmail.com>: >>>>>>>> >>>>>>>>> Hi! >>>>>>>>> I'm use oVirt 4.2.2 + Manageiq gaprindashvili-1.2018012514301 >>>>>>>>> 9_1450f27 >>>>>>>>> After i set this commits (upstream - https://bugzilla.redhat.com/ >>>>>>>>> 1542063) i no saw changes. >>>>>>>>> >>>>>>>>> >>>>>>>>> 2018-02-15 11:22 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: >>>>>>>>> >>>>>>>>>> Hi, >>>>>>>>>> >>>>>>>>>> What version of manageiq you are using? >>>>>>>>>> We had a bug https://bugzilla.redhat.com/1542152 (upstream - >>>>>>>>>> https://bugzilla.redhat.com/1542063) that was fixed in version >>>>>>>>>> 5.9.0.20 >>>>>>>>>> >>>>>>>>>> Please let me know it upgrading the version helped you. >>>>>>>>>> >>>>>>>>>> Thanks, >>>>>>>>>> Alona. >>>>>>>>>> >>>>>>>>>> On Wed, Feb 14, 2018 at 2:32 PM, Aliaksei Nazarenka < >>>>>>>>>> aliaksei.nazarenka(a)gmail.com> wrote: >>>>>>>>>> >>>>>>>>>>> Good afternoon! >>>>>>>>>>> I read your article - https://www.ovirt.org/develop/ >>>>>>>>>>> release-management/features/network/manageiq_ovn/. I have only >>>>>>>>>>> one question: how to create a network or subnet in Manageiq + ovirt 4.2.1. >>>>>>>>>>> When I try to create a network, I need to select a tenant, but there is >>>>>>>>>>> nothing that I could choose. How can it be? >>>>>>>>>>> >>>>>>>>>>> Sincerely. Alexey Nazarenko >>>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> >

1 0

Re: [ovirt-users] Manageiq ovn
by Alona Kaplan 15 Feb '18

15 Feb '18

On Thu, Feb 15, 2018 at 3:36 PM, Aliaksei Nazarenka < aliaksei.nazarenka(a)gmail.com> wrote: > when i try to create network router, i see this message: *Unable to > create Network Router "test_router": undefined method `[]' for nil:NilClass* > What ovn-provider version you're using? Can you please attach the ovn provider log ( /var/log/ovirt-provider-ovn.log)? > > 2018-02-15 16:20 GMT+03:00 Aliaksei Nazarenka < > aliaksei.nazarenka(a)gmail.com>: > >> Big Thank you! This work! But... Networks are created, but I do not see >> them in the ovirt manager, but through the ovn-nbctl command, I see all the >> networks. And maybe you can tell me how to assign a VM network from >> Manageiq? >> >> 2018-02-15 15:01 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: >> >>> >>> >>> On Thu, Feb 15, 2018 at 1:54 PM, Aliaksei Nazarenka < >>> aliaksei.nazarenka(a)gmail.com> wrote: >>> >>>> Error - 1 Minute Ago >>>> undefined method `orchestration_stacks' for >>>> #<ManageIQ::Providers::Redhat::InfraManager:0x00000007bf9288> - I get >>>> this message if I try to create a network of overts and then try to check >>>> the status of the network manager. >>>> >>> >>> It is the same bug. >>> You need to apply the fixes in https://github.com/ManageIQ/ma >>> nageiq-providers-ovirt/pull/198/files to make it work. >>> The best option is to upgrade your version. >>> >>> >>>> 2018-02-15 14:28 GMT+03:00 Aliaksei Nazarenka < >>>> aliaksei.nazarenka(a)gmail.com>: >>>> >>>>> I tried to make changes to the file refresher_ovn_provider.yml - >>>>> changed the passwords, corrected the names of the names, but it was not >>>>> successful. >>>>> >>>>> 2018-02-15 14:26 GMT+03:00 Aliaksei Nazarenka < >>>>> aliaksei.nazarenka(a)gmail.com>: >>>>> >>>>>> Hi! >>>>>> I'm use oVirt 4.2.2 + Manageiq gaprindashvili-1.2018012514301 >>>>>> 9_1450f27 >>>>>> After i set this commits (upstream - https://bugzilla.redhat.com/ >>>>>> 1542063) i no saw changes. >>>>>> >>>>>> >>>>>> 2018-02-15 11:22 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: >>>>>> >>>>>>> Hi, >>>>>>> >>>>>>> What version of manageiq you are using? >>>>>>> We had a bug https://bugzilla.redhat.com/1542152 (upstream - >>>>>>> https://bugzilla.redhat.com/1542063) that was fixed in version >>>>>>> 5.9.0.20 >>>>>>> >>>>>>> Please let me know it upgrading the version helped you. >>>>>>> >>>>>>> Thanks, >>>>>>> Alona. >>>>>>> >>>>>>> On Wed, Feb 14, 2018 at 2:32 PM, Aliaksei Nazarenka < >>>>>>> aliaksei.nazarenka(a)gmail.com> wrote: >>>>>>> >>>>>>>> Good afternoon! >>>>>>>> I read your article - https://www.ovirt.org/develop/ >>>>>>>> release-management/features/network/manageiq_ovn/. I have only one >>>>>>>> question: how to create a network or subnet in Manageiq + ovirt 4.2.1. When >>>>>>>> I try to create a network, I need to select a tenant, but there is nothing >>>>>>>> that I could choose. How can it be? >>>>>>>> >>>>>>>> Sincerely. Alexey Nazarenko >>>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> >

1 0

Re: [ovirt-users] Manageiq ovn
by Alona Kaplan 15 Feb '18

15 Feb '18

Hi Alexey, Please reply to the users list so all the user may enjoy the information. Automatic sync of ovn networks to ovirt was added on version ovirt-engine-4.2.1.3 (https://bugzilla.redhat.com/1511823) If you use lower version you should import the network to ovirt manually (networks tab -> import button). Once the ovn network is imported to ovirt a vnic profile is automatically created to it. In manageiq, you can assign this profile to a vm you provision (provision vm -> network tab -> vlan field). Alona. On Thu, Feb 15, 2018 at 3:20 PM, Aliaksei Nazarenka < aliaksei.nazarenka(a)gmail.com> wrote: > Big Thank you! This work! But... Networks are created, but I do not see > them in the ovirt manager, but through the ovn-nbctl command, I see all the > networks. And maybe you can tell me how to assign a VM network from > Manageiq? > > 2018-02-15 15:01 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: > >> >> >> On Thu, Feb 15, 2018 at 1:54 PM, Aliaksei Nazarenka < >> aliaksei.nazarenka(a)gmail.com> wrote: >> >>> Error - 1 Minute Ago >>> undefined method `orchestration_stacks' for >>> #<ManageIQ::Providers::Redhat::InfraManager:0x00000007bf9288> - I get >>> this message if I try to create a network of overts and then try to check >>> the status of the network manager. >>> >> >> It is the same bug. >> You need to apply the fixes in https://github.com/ManageIQ/ma >> nageiq-providers-ovirt/pull/198/files to make it work. >> The best option is to upgrade your version. >> >> >>> 2018-02-15 14:28 GMT+03:00 Aliaksei Nazarenka < >>> aliaksei.nazarenka(a)gmail.com>: >>> >>>> I tried to make changes to the file refresher_ovn_provider.yml - >>>> changed the passwords, corrected the names of the names, but it was not >>>> successful. >>>> >>>> 2018-02-15 14:26 GMT+03:00 Aliaksei Nazarenka < >>>> aliaksei.nazarenka(a)gmail.com>: >>>> >>>>> Hi! >>>>> I'm use oVirt 4.2.2 + Manageiq gaprindashvili-1.2018012514301 >>>>> 9_1450f27 >>>>> After i set this commits (upstream - https://bugzilla.redhat.com/ >>>>> 1542063) i no saw changes. >>>>> >>>>> >>>>> 2018-02-15 11:22 GMT+03:00 Alona Kaplan <alkaplan(a)redhat.com>: >>>>> >>>>>> Hi, >>>>>> >>>>>> What version of manageiq you are using? >>>>>> We had a bug https://bugzilla.redhat.com/1542152 (upstream - >>>>>> https://bugzilla.redhat.com/1542063) that was fixed in version >>>>>> 5.9.0.20 >>>>>> >>>>>> Please let me know it upgrading the version helped you. >>>>>> >>>>>> Thanks, >>>>>> Alona. >>>>>> >>>>>> On Wed, Feb 14, 2018 at 2:32 PM, Aliaksei Nazarenka < >>>>>> aliaksei.nazarenka(a)gmail.com> wrote: >>>>>> >>>>>>> Good afternoon! >>>>>>> I read your article - https://www.ovirt.org/develop/ >>>>>>> release-management/features/network/manageiq_ovn/. I have only one >>>>>>> question: how to create a network or subnet in Manageiq + ovirt 4.2.1. When >>>>>>> I try to create a network, I need to select a tenant, but there is nothing >>>>>>> that I could choose. How can it be? >>>>>>> >>>>>>> Sincerely. Alexey Nazarenko >>>>>>> >>>>>> >>>>>> >>>>> >>>> >>> >> >

1 0