- Users - oVirt List Archives

Windows VMs won't boot in debug mode
by Andrew X 17 Jul '18

17 Jul '18

Hi Everyone, I've been having problems getting Windows 10 VMs to boot in debug mode after turning on debugging over network (steps below). Also, device manager in Windows is not showing the processors' node which might be related (same reason why Windows is refusing to boot in debug mode?). I don't have any of these problems when I use generic KVM or Proxmox KVM. To turn on debugging in Windows, I do the follwoing from an admin terminal window: bcdedit /debug on bcdedit /dbgsettings net hostip:a.b.c.d port:p key:1.2.3.4 Any help will be appreciated, Thanks, Andrew

1 0

oVirt Metrics
by Shirly Radco 17 Jul '18

17 Jul '18

Dear users, I would love to get some feedback if someone has tried to install and use the oVirt metrics store, released in 4.2, for collecting metrics and logs, based on Elasticsearch, Kibana, Collectd and Fluentd on top of OpenShift. https://www.ovirt.org/develop/release-management/features/metrics/metrics-s… How did the installation go? Are you actively using it? And any other feedback would be much appreciated. Best regards, -- SHIRLY RADCO BI SeNIOR SOFTWARE ENGINEER Red Hat Israel <https://www.redhat.com/> <https://red.ht/sig> TRIED. TESTED. TRUSTED. <https://redhat.com/trusted>

7 25

oVirt node not installed
by Spickiy Nikita 17 Jul '18

17 Jul '18

Hi, i try install oVirt node, but getting errors on step post-install script. Screen error in attachment. [cid:944CCD96-B8FF-4ABA-AF17-FA6A7DC184BB@digital-ecosystems.ru] [cid:8D77635B-AF62-4894-A9E2-F57E9F290DE5@digital-ecosystems.ru]

2 1

Disk Statistics API in oVirt
by Hari Prasanth Loganathan 17 Jul '18

17 Jul '18

Hi Team, We are using the following API to collect the disk statistics, https://X.X.X.2/ovirt-engine/api/ *disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda/statistics* <https://X.X.X.2/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda…> I found one issue in the disk statistics. In case If the Virtual Machine has this disk (*2331bad7-71ec-4fad-95bb-2b3449f3dbda*) attached to it and I perform some read / write operation in the VM and it increases the corresponding disk level Read data rate / Write data rate / disk.read.latency / disk.write.latency. *Example*, I received the following values for this disk, But the problem is even when I bring down the VM still the last known value is received continuously. *Is it a known issue Or any workaround is available? * *Expected : All values should go to Zero* *Actual : All values retains the last known values when the VM was in UP state. * { "statistic": [ { "kind": "gauge", "type": "decimal", "unit": "bytes_per_second", "values": { "value": [ { "datum": 2184 } ] }, "disk": { "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda", "id": "2331bad7-71ec-4fad-95bb-2b3449f3dbda" }, "name": "data.current.read", "description": "Read data rate", "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda/statistics/33b9212b-f9cb-3fd0-b364-248fb61e1272", "id": "33b9212b-f9cb-3fd0-b364-248fb61e1272" }, { "kind": "gauge", "type": "decimal", "unit": "bytes_per_second", "values": { "value": [ { "datum": 41202005 } ] }, "disk": { "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda", "id": "2331bad7-71ec-4fad-95bb-2b3449f3dbda" }, "name": "data.current.write", "description": "Write data rate", "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda/statistics/2f23addd-4ebd-3d82-a449-c28778bc33eb", "id": "2f23addd-4ebd-3d82-a449-c28778bc33eb" }, { "kind": "gauge", "type": "decimal", "unit": "seconds", "values": { "value": [ { "datum": 0.12 } ] }, "disk": { "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda", "id": "2331bad7-71ec-4fad-95bb-2b3449f3dbda" }, "name": "disk.read.latency", "description": "Read latency", "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda/statistics/3a7b3f72-d035-3bb9-b196-e86a4eb34993", "id": "3a7b3f72-d035-3bb9-b196-e86a4eb34993" }, { "kind": "gauge", "type": "decimal", "unit": "seconds", "values": { "value": [ { "datum": 1.4 } ] }, "disk": { "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda", "id": "2331bad7-71ec-4fad-95bb-2b3449f3dbda" }, "name": "disk.write.latency", "description": "Write latency", "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda/statistics/b1e75c7b-cea4-37d2-8459-f7d68efc69a3", "id": "b1e75c7b-cea4-37d2-8459-f7d68efc69a3" }, { "kind": "gauge", "type": "decimal", "unit": "seconds", "values": { "value": [ { "datum": 0 } ] }, "disk": { "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda", "id": "2331bad7-71ec-4fad-95bb-2b3449f3dbda" }, "name": "disk.flush.latency", "description": "Flush latency", "href": "/ovirt-engine/api/disks/2331bad7-71ec-4fad-95bb-2b3449f3dbda/statistics/9c17ad7b-9ef1-3e8d-ad0a-ff8bee3925f0", "id": "9c17ad7b-9ef1-3e8d-ad0a-ff8bee3925f0" } ] } Thanks, Hari -- DISCLAIMER - *MSysTechnologies LLC* This email message, contents and its attachments may contain confidential, proprietary or legally privileged information and is intended solely for the use of the individual or entity to whom it is actually intended. If you have erroneously received this message, please permanently delete it immediately and notify the sender. If you are not the intended recipient of the email message,you are notified strictly not to disseminate,distribute or copy this e-mail.E-mail transmission cannot be guaranteed to be secure or error-free as Information could be intercepted, corrupted, lost, destroyed, incomplete or contain viruses and MSysTechnologies LLC accepts no liability for the contents and integrity of this mail or for any damage caused by the limitations of the e-mail transmission.

1 1

Network storage traffic
by John Nguyen 16 Jul '18

16 Jul '18

Hello, This is more out of curiosity, I was wondering during a migration or import/export does all the storage traffic goes through the SPM server? Thanks John

1 0

ovirt 4.2.4 installation failures
by Vineet Khandpur 16 Jul '18

16 Jul '18

Building a snadbox ovirt environment on CentOS 7.5.1804 Install fails at Creating CA stage: [ INFO ] Configuring PostgreSQL [ INFO ] Creating CA [ ERROR ] Failed to execute stage 'Misc configuration': [Errno 2] No such file or directory [ INFO ] Yum Performing yum transaction rollback [ INFO ] Stage: Clean up Log file is located at /var/log/ovirt-engine/setup/ovirt-engine-setup-20180712081855-efeaj4.log [ INFO ] Generating answer file '/var/lib/ovirt-engine/setup/answers/20180712082036-setup.conf' [ INFO ] Stage: Pre-termination [ INFO ] Stage: Termination [ ERROR ] Execution of setup failed /etc/pki/ovirt-engine missing several files after install (compared to our prod and test systems) Did something change with the installation re. cert creation? Or am I missing something obvious? [note: default answers to installation questions] Thanks. vk -------------------------------- Vineet Khandpur UNIX System Administrator Information Technology Services University of Alberta Libraries +1-780-492-4718

2 5

Jump from a disk to its storage domain from VM disk
by Gianluca Cecchi 16 Jul '18

16 Jul '18

Hello, currently on 4.2.3 I can - Select Storage --> Disks - Select disk link in the line (in the "Alias" column) - In the new disk page select "Storage" tab and I can see the related Domain Name and its information (eg free space if I want to extend the disk) --> it would be nice to have a "link" on domain name so that you can directly jump to Storage --> Domains --> Domain Name It would be nice to have similar behavior also directly starting from Compute --> Virtual Machines Select VM --> Disks Select disk Here I can select "edit" and then in the edit window I can see information about storage domain between the other fields. It would be nice to have a pointer to directly go to the storage domain containing that disk. Gianluca

1 0

oVirt - Scaling out from one to many
by Leo David 16 Jul '18

16 Jul '18

Hello everyone, I have two things that i really need to understand regarding storage scaling using gluster. Basically, I am trying to figure out a way to go from 1 single instance to multiple nodes cluster. 1. Single node SelfHosted Engine HyperConverged setup - scale instance up to 3 nodes: - the gluster volumes are created as distributed type. - is there a procedure to migate this single-host scenario to multiple nodes, considering that the 3 nodes setup is using replica 3 gluster volumes ? 2. 3 Nodes SelfHosted Engine - add more storage nodes - how should I increase the size of the already present replica 3 volumes ? - should the volumes be as distribute-replicated in an environment larger than 3 nodes ? 3. Is there a limit as a maximum number of compute nodes per cluster ? Thank you very much ! Leo -- Best regards, Leo David

3 5

VM stuck in "Migrating to"
by Bruckner, Simone 15 Jul '18

15 Jul '18

Hi all, I have a VM stuck in state "Migrating to". I restarted ovirt-engine and rebooted all hosts, no success. I run ovirt 4.2.4.5-1.el7 on CentOS 7.5 hosts with vdsm-4.20.32-1.el7.x86_64. How can I clean this up? Thank you and all the best, Simone

3 4

ovirt 3.8 to ovirt 4.2 Migration.
by techieim 15 Jul '18

15 Jul '18

Hello Team Ovirt, We are running Ovirt3.8 version in our prod, we want to upgrade to 3.8 to 4.2. At present we have 2 (hyp A & hyp B)physical host ovirt 3.8 is running with self hosted engine with data domain and iso one cluster and data center. What we were thing do this migration in following fashion. Plan A. 1. Attach export domain present infra. 2. Take backup all of running vm as export. 3. Detach export domain 4. Detach hyp B from cluster and data center 5. Install fresh ovirt 4.2 iso on hyp B 6. Install self hosted engine 7. Attach Data Domain 8. Attach Export Domain which was use in ovirt 3.8 9. Import all vm's from there to new ovirt 4.2 10. Once all the vm's got up and running poweroff hyp A 11. Install fresh ovirt 4.2 iso on hyp A and attach cluster. Plan B. 1. Attach export domain present infra. 2. Take backup all of running vm as export. 3. Detach export domain 4. Detach hyp B from cluster and data center 5. Install fresh ovirt 4.2 iso on hyp B 6. Install self hosted engine 7. Attach Data Domain 8. Export from ovirt 3.8 to ovirt 4.2 9. Once all the vm's got up and running poweroff hyp A 10. Install fresh ovirt 4.2 iso on hyp A and attach cluster. Thank a ton in advance we may be wrong with above step help us to win this migration. Regards Techieim

1 0

[ANN] oVirt 4.2.5 Second Release Candidate is now available
by Lev Veyde 15 Jul '18

15 Jul '18

The oVirt Project is pleased to announce the availability of the oVirt 4.2.5 Second Release Candidate, as of July 15th, 2018. This update is a release candidate of the fifth in a series of stabilization updates to the 4.2 series. This is pre-release software. This pre-release should not to be used in production. This release is available now for: * Red Hat Enterprise Linux 7.5 or later * CentOS Linux (or similar) 7.5 or later This release supports Hypervisor Hosts running: * Red Hat Enterprise Linux 7.5 or later * CentOS Linux (or similar) 7.5 or later See the release notes [1] for installation / upgrade instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is available - oVirt Node is available [2] Additional Resources: * Read more about the oVirt 4.2.5 release highlights: http://www.ovirt.org/release/4.2.5/ * Get more oVirt Project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] http://www.ovirt.org/release/4.2.5/ [2] http://resources.ovirt.org/pub/ovirt-4.2-pre/iso/ -- Lev Veyde Software Engineer, RHCE | RHCVA | MCITP Red Hat Israel <https://www.redhat.com> lev(a)redhat.com | lveyde(a)redhat.com <https://red.ht/sig> TRIED. TESTED. TRUSTED. <https://redhat.com/trusted>

1 0

oVirt reports using Grafana
by Karli Sjöberg 15 Jul '18

15 Jul '18

Heya! I've been whishing for reports in oVirt ever since the old 'Jasper Reports' was removed. For an Enterprise, having pretty graphs to look at is a must. Searching the subject, I've found this[*] and have managed to get it installed OK but having issues trying to follow the guide setting it up. First of all, I think the guide should have at least mentioned that 'pg_hba.conf' needs to be edited for the read only user to be able to connect to the database, I scratched my head around that for a while before I got it. When I first type in the query example, I got syntax errors: 'pq: syntax error at or near "$"'. I continued anyways since I figured it would be solved at a later point, which turned out to be true, since the next step is to use the "Templating feature" to add variables. Unfortunately this doesn't go so well, even though I followed the instructions very carefully. After hitting save on the first variable I am rewarded with the error message: 'Template variables could not be initialized: pq: column "en_us" does not exist.' Are the queries stated in the guide still correct? This is for 'user_locale': "SELECT DISTINCT language_code from enum_translator" [*]:https://www.ovirt.org/blog/2018/01/ovirt-report-using-grafana/ TIA /K

5 8

new setup would like some advise on implementetion
by Georgios Vasilopoulos 14 Jul '18

14 Jul '18

Hello! I would like to read your thoughts regarding a new implementation we are about to do at work Our infrastructure is as follows There are 9 servers who will be used for running vm's Network is 2x10G + 4x1G ethernet per server each has 2x 10C xeon processors and 192GB RAM and 2x 300GB 10K Enterprise SAS 6Gbps, Hot Swap HDD There are 3 servers who will be used for storage. Network is 2x10G + 4x1G ethernet per server each has 2x 8c Xeon processors with 128GB RAM 2x 300GB 10000RPM, 2.5", Serial Attached SCSI (SAS), Hot Swap 6x 200GB WesternDigital HGST ultrastar HUSMM1620ASS200 ssd Each server has a jbod box connected to the server through sas interface 12x 4TB The ovirt installation is expected to run 250-200 VM's on maximum load. Expected to run on a big VM there is our mail server which is pretty loaded, has about 50000 registred users and about half of them are pretty active. What I'm currently thinking is : have hosted vm on compute servers storage, as a stand alone non managed volume of about 150GB. but I would like the engine to be stored on more than 3 servers. Any thoughts ? On the vm storage since high availability is a must I will probably set the servers in raid6 with a spare each and then I will do 3 volumes(2 data bricks + 1 arbiter brick on each server) on glusterfs replica 3 arbiter 1. This will give me about 36TB usable per storage server. I'm highly concerned on how glusterfs will perform regarding the email server. Right now email server is on a vm running on KVM and it gets it's storage from an EMC storage. I'm not expecting Gluster to perform as the EMC storage but I would like to know if it can handle it. I'm thinking of dedicating a gluster volume exclusively Is it better to give to the email vm the gluster volume as a disk(s) from ovirt or directly mount it through the vm? ovirt will force the use of gfapi if I set it on the engine. on the other hand if I use this, how sharding will perform. On the other hand, If I mount it as a glusterfs volume directly on the vm how will it perform through fuse? I have 6x200gb ssd's per storage server. Will it do any good to add these as a tiering volume? What should the shard block size be in that case should it be smaller to utilise the ssd's better ? Will performance be better if I use ceph through iscsi with multipath? I read that ceph needs more nodes to perform suitably and that iscsi adds considerable overhead. I'd love to read your thoughts on this.

1 0

Problem with following host link for vm list using Java SDK.
by dchambers＠bugfixer.net 13 Jul '18

13 Jul '18

When trying to do VM list using the 4.2.4 Java SDK against a 4.2.4 engine, I am getting an error while trying to follow the host link to get host info. Any suggestions on fixing this? List<Vm> vms = vmsService.list() .follow("host") .send().vms(); Exception in thread "main" org.ovirt.engine.sdk4.Error: Failed to send request at org.ovirt.engine.sdk4.internal.HttpConnection.send(HttpConnection.java:255) at org.ovirt.engine.sdk4.internal.HttpConnection.send(HttpConnection.java:229) at org.ovirt.engine.sdk4.internal.services.VmsServiceImpl$ListRequestImpl.send(VmsServiceImpl.java:563) at org.ovirt.engine.sdk4.internal.services.VmsServiceImpl$ListRequestImpl.send(VmsServiceImpl.java:477) at com.foo.ovirt.test.VMList.main(VMList.java:59) Caused by: org.ovirt.engine.sdk4.Error: The response content type 'text/html;charset=UTF-8' isn't the expected XML at org.ovirt.engine.sdk4.internal.HttpConnection.checkContentType(HttpConnection.java:287) at org.ovirt.engine.sdk4.internal.HttpConnection.send(HttpConnection.java:251) ... 4 more

2 2

Host reboot failed
by Nicolas Ecarnot 13 Jul '18

13 Jul '18

Hello, [oVirt 4.2.4.5-1.el7] Sequence : - Among 7 active UP hosts, one of them runs zero VM - On this (still in UP state) host, I run a SSH-restart via the web GUI - The host gracefully shuts down then reboots, with no issue - In the web GUI, as in real life, the host stays in Reboot state forever A this point, the engine can ping it, can ssh-connect to it, the host seems to have zero issue. In the web GUI, I can not put it into active state because it is not in maintenance state. It stays in reboot state. I can not either put it in maintenance state because it stays in reboot state. This state lasts long enough to allow me type this mail, look into logs, and as I was about to send logs, I see the host is returning to life (its states comes back as UP). I don't type fast, so after the host has finished rebooting, maybe 5 or 10 minutes have passed before the engine links again to the host. Before posting additional logs and comments, does anybody know if this is a know bug or behavior, or do I have to open a BZ? Regards, -- Nicolas ECARNOT

1 0

Re: NFS Mount on EMC VNXe3200 / User - Group 36:36 / Permission issue
by Karli Sjöberg 12 Jul '18

12 Jul '18

2 1

ovirt 3.5 fail to start on centOS 6.9
by dinushawww＠gmail.com 12 Jul '18

12 Jul '18

Hi, After installing ovirt 3.5 on centOS6.9 the ovirt-engine has stopped. while restarting the engine the error comes "/usr/share/jboss-as" not found. I installed jboss-as7.7.7final and again restart ovirt-engine. now it says ovirt-engine started, but when i checj the status, it shows ovirt-engine stopped, but PID file exist. Please help me to solve this. because i want to crate a lab using 3.5 for my exam. Thank You Dinusha

1 0

Installing ovirt 3.6 on centOS 6.9 error
by dinushawww 12 Jul '18

12 Jul '18

Hi, After install ovirt 3.5 on centOS 6.9, the ovirt engine has stopped. while trying to start ovirt-engine it will say /usr/share/jboss-as not found. i manually download jboss 7.1.1 final and installed in /usr/share and again start the oviert-engine, this time it will start and then run the command service ovirt-engine status, ovirt-engine stopped, pid file exist. please help me to solve. i need to crate a lab using ovirt 3.5. Thank You Dinusha

1 0

VDI - SPICE zero clients
by cmcl＠dneg.com 12 Jul '18

12 Jul '18

Hi, I gt hold of a 10zig V1200-P for testing VDI under ovirt/RHEV, as I'd read that they support SPICE. However, I haven't found how to connect it successfully to a VM as yet. Has anyone had any experience with these using ovirt/RHEV? I haven't been able to find any manuals or support info on the 10zig website regarding these V1200-P zero clients. I've read that they are discontinuing SPICE support in the future, but I just need to be able to demonstrate it working for now. Thanks for any help, Cam

2 2

Console issues in a distributed environment over NAT
by shailigum＠gmail.com 11 Jul '18

11 Jul '18

Hi all, i'm trying to deploy oVirt to manage multiple 'data centers' (really just very basic deployments of single hosts using local storage that are deployed in varying geographic locations), where each host/resource pool is (unfortunately) only accessible via NAT. I've setup port-forwards for all functions, including SPICE/VNC, but am running into issues with the 'console' button in the GUI. When I initially added the host I added it using the NAT IP, however when trying to connect to console the console.vv file generated from the GUI references the local (private) IP of the host, instead of the NAT IP of the upstream firewall - so I have to manually open the file to change it to the NAT IP in order to connect to a VM's console. This is a minor annoyance for me, but it does ultimately the tool will be used by others who are less comfortable with steps like these. Is there a way around this, to have the console.vv generate with the IP oVirt is using to connect to the host, instead of its discovered local IP? Also if you can think of any other concerns I may encounter in a NAT deployment like this, please share! Thanks!

1 0

NFS Mount on EMC VNXe3200 / User - Group 36:36 / Permission issue
by jeanbaptiste.coupiac＠nfrance.com 11 Jul '18

11 Jul '18

Hello, I try to mount an NFS Data share from a EMC VNXe3200 export. Unfortunately, NFS share cannot be mount, there is permission error. (Indeed, after the same issue on another NFS ISO repo, I've change exported directory user/group to 36:36, and O-Virt NFS mount was great). So, I think issue with my VNXe3200 is regarding UID / GID owner on VNXe3200 side. After webex with EMC support, change owner / permission on VNXe side seems not possible / supported. Can I mount the NFS share with some options to avoid vdsm:kvm mounting issue ? Can I force mount with root ? Regards, Jean-Baptiste COUPIAC

1 0

Engine Error
by Sakhi Hadebe 11 Jul '18

11 Jul '18

Hi, I have just re-installed centOS 7 in 3 servers and have configured gluster volumes following this documentation: https://www.ovirt.org/blog/2016/03/up-and-running-with-ovirt-3-6/, But I have installed http://resources.ovirt.org/pub/yum-repo/ovirt-release42.rpm package. Hosted-engine --deploy is failing with this error: "rhel7", "--virt-type", "kvm", "--memory", "16384", "--vcpus", "4", "--network", "network=default,mac=00:16:3e:09:5e:5d,model=virtio", "--disk", "/var/tmp/localvm0nnJH9/images/eacac30d-0304-4c77-8753-6965e4b8c2e7/d494577e-027a-4209-895b-6132e6fc6b9a", "--import", "--disk", "path=/var/tmp/localvm0nnJH9/seed.iso,device=cdrom", "--noautoconsole", "--rng", "/dev/random", "--graphics", "vnc", "--video", "vga", "--sound", "none", "--controller", "usb,model=none", "--memballoon", "none", "--boot", "hd,menu=off", "--clock", "kvmclock_present=yes"], "delta": "0:00:00.979003", "end": "2018-07-10 17:55:11.308555", "msg": "non-zero return code", "rc": 1, "start": "2018-07-10 17:55:10.329552", "stderr": "ERROR unsupported configuration: CPU mode 'custom' for x86_64 kvm domain on x86_64 host is not supported by hypervisor\nDomain installation does not appear to have been successful.\nIf it was, you can restart your domain by running:\n virsh --connect qemu:///system start HostedEngineLocal\notherwise, please restart your installation.", "stderr_lines": ["ERROR unsupported configuration: CPU mode 'custom' for x86_64 kvm domain on x86_64 host is not supported by hypervisor", "Domain installation does not appear to have been successful.", "If it was, you can restart your domain by running:", " virsh --connect qemu:///system start HostedEngineLocal", "otherwise, please restart your installation."], "stdout": "\nStarting install...", "stdout_lines": ["", "Starting install..."]} I added the root user to the kvm group. but it ddn't work. Can you please help me out. I have been struggling to deploy the hosted engine. -- Regards, Sakhi

2 3

PXE LOCALBOOT issue
by Michael Deffenbaugh 11 Jul '18

11 Jul '18

Hey all, Provisioning a host with Foreman 1.17.1/Katello 3.6. The host kickstarts fine but when it goes to reboot, iPXE fails to load the local disk when the Foreman local boot kickstart menu ( https://github.com/theforeman/community-templates/blob/develop/provisioning…, line 4-10) sends the command "LOCALBOOT 0". It simply fails and says "No more network devices. No bootable device." Is this a bug in iPXE? Any input would be greatly appreciated! Regards, Mike

1 1

upload disk using python sdk
by 董青龙 11 Jul '18

11 Jul '18

Hi all, I want to upload an disk using python sdk instead of web. Which class should I use? I could not find a "upload" method in "class Disk" an "class Disks" in "brokers.py" Anyone can help? Thanks!

2 1

Re: hosted-engine install fails (was: Engine Error)
by Yedidyah Bar David 11 Jul '18

11 Jul '18

On Tue, Jul 10, 2018 at 11:32 PM, Sakhi Hadebe <sakhi(a)sanren.ac.za> wrote: > Hi, > > I did not select any CPU architecture. It doenst gove me the option to > select one. It only states the number of virtual CPUs and the memory for > the engine VM. > > Looking at the documentation of installing ovirt-release36.rpm....it does > allow you to select te CPU, but not when installing ovirt-release42.rpm > > On Tuesday, July 10, 2018, Alastair Neil <ajneil.tech(a)gmail.com> wrote: > >> what did you select as your CPU architecture when you created the >> cluster? It looks like the VM is trying to use a CPU type of "Custom", how >> many nodes in your cluster? I suggest you specify the lowest common >> denominator of CPU architecture (e.g. Sandybridge) of the nodes as the CPU >> architecture of the cluster.. >> >> On Tue, 10 Jul 2018 at 12:01, Sakhi Hadebe <sakhi(a)sanren.ac.za> wrote: >> >>> Hi, >>> >>> I have just re-installed centOS 7 in 3 servers and have configured >>> gluster volumes following this documentation: >>> https://www.ovirt.org/blog/2016/03/up-and-running-with-ovirt-3-6/, But >>> I have installed >>> >>> http://resources.ovirt.org/pub/yum-repo/ovirt-release42.rpm >>> >>> package. >>> Hosted-engine --deploy is failing with this error: >>> >>> "rhel7", "--virt-type", "kvm", "--memory", "16384", "--vcpus", "4", >>> "--network", "network=default,mac=00:16:3e:09:5e:5d,model=virtio", >>> "--disk", "/var/tmp/localvm0nnJH9/images/eacac30d-0304-4c77-8753- >>> 6965e4b8c2e7/d494577e-027a-4209-895b-6132e6fc6b9a", "--import", >>> "--disk", "path=/var/tmp/localvm0nnJH9/seed.iso,device=cdrom", >>> "--noautoconsole", "--rng", "/dev/random", "--graphics", "vnc", "--video", >>> "vga", "--sound", "none", "--controller", "usb,model=none", "--memballoon", >>> "none", "--boot", "hd,menu=off", "--clock", "kvmclock_present=yes"], >>> "delta": "0:00:00.979003", "end": "2018-07-10 17:55:11.308555", "msg": >>> "non-zero return code", "rc": 1, "start": "2018-07-10 17:55:10.329552", >>> "stderr": "ERROR unsupported configuration: CPU mode 'custom' for x86_64 >>> kvm domain on x86_64 host is not supported by hypervisor\nDomain >>> installation does not appear to have been successful.\nIf it was, you can >>> restart your domain by running:\n virsh --connect qemu:///system start >>> HostedEngineLocal\notherwise, please restart your installation.", >>> "stderr_lines": ["ERROR unsupported configuration: CPU mode 'custom' for >>> x86_64 kvm domain on x86_64 host is not supported by hypervisor", "Domain >>> installation does not appear to have been successful.", "If it was, you can >>> restart your domain by running:", " virsh --connect qemu:///system start >>> HostedEngineLocal", "otherwise, please restart your installation."], >>> "stdout": "\nStarting install...", "stdout_lines": ["", "Starting >>> install..."]} >>> >> This seems to be in the phase where we create a local vm for the engine. We do this with plain virt-install, nothing fancy. Searching the net for "unsupported configuration: CPU mode 'custom'" finds other relevant reports, you might want to check them. You can see the command in bootstrap_local_vm.yml . Please check/share versions of relevant packages (libvirt*, qemu*, etc) and relevant logs (libvirt). Also updating the subject line and adding Simone. Best regards, -- Didi

1 0