- Users - oVirt List Archives

Virtual Machine looses connectivity with no clear explanation
by FERNANDO FREDIANI 03 Jul '17

03 Jul '17

This is a multi-part message in MIME format. --------------CA6FA101A23C7121C82BF9C5 Content-Type: text/plain; charset=utf-8; format=flowed Content-Transfer-Encoding: 7bit I have a rather strange issue which is affecting one of my last deployed Hypervisors. It is a CentOS 7 (not a oVirt Node) which runs only 3 Virtual Machines. One of these VMs have a reasonable output traffic at peaks (500 - 700Mbps) and the hypervisor underneath is connected to the switch via a bonding (mode=2) which in turn creates bond0.XX interfaces which are connected to different bridges for each network. The VM in question is connected to bridge "ovirtmgmt". When the problem happens the VM stops passing traffic and cannot reach even the router or other VMs in the same Layer 2. Seems the bridge stop passing traffic for that particular VM. Other VMs work fine since they were created. When this problem happens I just need to go to its Console and run a reboot (Ctrl-Alt-Del), don't even need to Power Off and Power On again using oVirt Engine. I have even re-installed this VMs operating system from scratch but the problem persists. Have also changed the vNic mac address in the case (already check) of conflicted mac addresses somewhere in that Layer 2. Last, my hypervisor machine (due a mistake) has been running with SElinux disabled, not sure if it could have anything to do with this behavior. Anyway, anyone has ever seen any behavior like that ? Thanks Fernando --------------CA6FA101A23C7121C82BF9C5 Content-Type: text/html; charset=utf-8 Content-Transfer-Encoding: 7bit <html> <head> <meta http-equiv="content-type" content="text/html; charset=utf-8"> </head> <body bgcolor="#FFFFFF" text="#000000"> <font face="arial, helvetica, sans-serif">I have a rather strange issue which is affecting one of my last deployed Hypervisors. It is a CentOS 7 (not a oVirt Node) which runs only 3 Virtual Machines.<br> <br> One of these VMs have a reasonable output traffic at peaks (500 - 700Mbps) and the hypervisor underneath is connected to the switch via a bonding (mode=2) which in turn creates bond0.XX interfaces which are connected to different bridges for each network. The VM in question is connected to bridge "ovirtmgmt".<br> <br> When the problem happens the VM stops passing traffic and cannot reach even the router or other VMs in the same Layer 2. Seems the bridge stop passing traffic for that particular VM. Other VMs work fine since they were created. When this problem happens I just need to go to its Console and run a reboot (Ctrl-Alt-Del), don't even need to Power Off and Power On again using oVirt Engine.<br> I have even re-installed this VMs operating system from scratch but the problem persists. Have also changed the vNic mac address in the case (already check) of conflicted mac addresses somewhere in that Layer 2.<br> <br> Last, my hypervisor machine (due a mistake) has been running with SElinux disabled, not sure if it could have anything to do with this behavior.<br> <br> Anyway, anyone has ever seen any behavior like that ?<br> <br> Thanks<br> Fernando<br> </font> </body> </html> --------------CA6FA101A23C7121C82BF9C5--

1 0

Re: [ovirt-users] Recovering hosted-engine
by Andrew Dent 03 Jul '17

03 Jul '17

--------=_MB15379295-79C3-4E7D-BA3E-C6F662EE3B38 Content-Type: text/plain; format=flowed; charset=utf-8 Content-Transfer-Encoding: quoted-printable Has anyone successfully completed a hosted-engine recovery on a multiple=20 host setup with production VMs? Kind regards Andrew ------ Original Message ------ From: "Andrew Dent" <adent(a)ctcroydon.com.au> To: "users" <users(a)ovirt.org> Sent: 2/07/2017 2:22:16 PM Subject: [ovirt-users] Recovering hosted-engine >Hi > >A couple of questions about hosted-engine recovery. >Part way through this URL, in the section "Workflow for Restoring the=20 >Self-Hosted Engine Environment" >http://www.ovirt.org/documentation/self-hosted/chap-Backing_up_and_Restori= ng_an_EL-Based_Self-Hosted_Environment/ >it looks like once the hosted-engine is recovered on Host 1, the VMs on=20 >Host 2 and 3 will be running, but not accessible to the recovered=20 >Hosted Engine. >Is that correct? >If so, how to you remove host 2 and host 3 from the environment, then=20 >add back in again while keeping the VMs running? > >Host 2 and Host 3 are not recoverable in their current state. These=20 >hosts need to be removed from the environment, and then added again to=20 >the environment using the hosted-engine deployment script. For more=20 >information on these actions, see the Removing Non-Operational Hosts=20 >from a Restored Self-Hosted Engine Environment section below and=20 >Chapter 7: Installing Additional Hosts to a Self-Hosted Environment=20 ><http://www.ovirt.org/documentation/self-hosted/chap-Backing_up_and_Restor= ing_an_EL-Based_Self-Hosted_Environment/chap-Installing_Additional_Hosts_to= _a_Self-Hosted_Environment>. > >BTW: The link referring to chapter 7 is broken. > >Kind regards > > > >Andrew > > --------=_MB15379295-79C3-4E7D-BA3E-C6F662EE3B38 Content-Type: text/html; charset=utf-8 Content-Transfer-Encoding: quoted-printable <?xml version=3D"1.0" encoding=3D"utf-16"?><html><head> <style id=3D"signatureStyle" type=3D"text/css"></style><style type=3D"text/css"></style> <style type=3D"text/css"></style> </head> <body><div>Has anyone successfully completed a hosted-engine recovery on a= multiple host setup with production VMs?</div><div><br /></div><div id=3D"s= ignature_old"><div id=3D"xb62ca86bd62b482"><div style=3D"font-family: Tahom= a;"><span id=3D"x89c8d9902b0345bca5fb60b10010a8ea"><font> <div id=3D"x136253a26533439c817a2d4cd93dbb00"><div id=3D"signature_old"><di= v id=3D"xea120d60c95044d"><div class=3D"WordSection1"><div id=3D"xb71224f92= 0234978acc74f4d23143069"><div class=3D"WordSection1"><p class=3D"MsoNormal"= ><font size=3D"4" style=3D"font-size: 14pt;">Kind regards</font></p><p clas= s=3D"MsoNormal"><font size=3D"4" style=3D"font-size: 14pt;"><br /></font></= p><p class=3D"MsoNormal"><font size=3D"4" style=3D"font-size: 14pt;">Andrew= =C2=A0</font></p></div></div></div></div></div></div></font></span></div></= div></div><div><br /></div><div><br /></div> <div>------ Original Message ------</div> <div>From: "Andrew Dent" <<a href=3D"mailto:adent@ctcroydon.com.au">aden= t(a)ctcroydon.com.au</a>></div> <div>To: "users" <<a href=3D"mailto:users@ovirt.org">users(a)ovirt.org</a>= ></div> <div>Sent: 2/07/2017 2:22:16 PM</div> <div>Subject: [ovirt-users] Recovering hosted-engine</div><div><br /></div> <div id=3D"xa03d74168c5b47d"><blockquote cite=3D"a55544f993c0aef5fbfa13e1ed= 78ca048e629118@localhost" type=3D"cite" class=3D"cite2"> <div>Hi</div><div><br /></div><div>A couple of questions about hosted-engin= e recovery.</div><div>Part way through this URL, in the section "Workflow f= or Restoring the Self-Hosted Engine Environment"=C2=A0</div><div><a href=3D= "http://www.ovirt.org/documentation/self-hosted/chap-Backing_up_and_Restori= ng_an_EL-Based_Self-Hosted_Environment/">http://www.ovirt.org/documentation= /self-hosted/chap-Backing_up_and_Restoring_an_EL-Based_Self-Hosted_Environm= ent/</a></div><div>it looks like once the hosted-engine is recovered on Hos= t 1, the VMs on Host 2 and 3 will be running, but not accessible to the rec= overed Hosted Engine.=C2=A0</div><div>Is that correct?</div><div>If so, how = to you remove host 2 and host 3 from the environment, then add back in aga= in while keeping the VMs running?</div><div><br /></div><div><div> <code style=3D"box-sizing: border-box; font-family: Menlo, Monaco, Consolas= , 'Courier New', monospace; font-size: 14.4px; padding: 2px 4px; color: rgb= (199, 37, 78); border-radius: 4px; font-variant-ligatures: normal; orphans: = 2; widows: 2; background-color: rgb(249, 242, 244);">Host 2</code><span st= yle=3D"color: rgb(51, 51, 51); font-family: 'Source Sans Pro', 'Open Sans', = 'Helvetica Neue', Helvetica, Arial, sans-serif; font-variant-ligatures: no= rmal; orphans: 2; widows: 2; background-color: rgb(255, 255, 255);">=C2=A0a= nd=C2=A0</span><code style=3D"box-sizing: border-box; font-family: Menlo, M= onaco, Consolas, 'Courier New', monospace; font-size: 14.4px; padding: 2px= 4px; color: rgb(199, 37, 78); border-radius: 4px; font-variant-ligatures: n= ormal; orphans: 2; widows: 2; background-color: rgb(249, 242, 244);">Host 3= </code><span style=3D"color: rgb(51, 51, 51); font-family: 'Source Sans Pro= ', 'Open Sans', 'Helvetica Neue', Helvetica, Arial, sans-serif; font-varian= t-ligatures: normal; orphans: 2; widows: 2; background-color: rgb(255, 255, = 255);">=C2=A0are not recoverable in their current state. These hosts need= to be removed from the environment, and then added again to the environment = using the hosted-engine deployment script. For more information on these a= ctions, see the Removing Non-Operational Hosts from a Restored Self-Hosted= Engine Environment section below and=C2=A0</span><a href=3D"http://www.ovir= t.org/documentation/self-hosted/chap-Backing_up_and_Restoring_an_EL-Based_S= elf-Hosted_Environment/chap-Installing_Additional_Hosts_to_a_Self-Hosted_En= vironment" style=3D"box-sizing: border-box; color: rgb(97, 182, 14); text-d= ecoration: none; font-family: 'Source Sans Pro', 'Open Sans', 'Helvetica Ne= ue', Helvetica, Arial, sans-serif; font-variant-ligatures: normal; orphans: = 2; widows: 2; background-color: rgb(255, 255, 255);">Chapter 7: Installing = Additional Hosts to a Self-Hosted Environment</a><span style=3D"color: rgb= (51, 51, 51); font-family: 'Source Sans Pro', 'Open Sans', 'Helvetica Neue'= , Helvetica, Arial, sans-serif; font-variant-ligatures: normal; orphans: 2; = widows: 2; background-color: rgb(255, 255, 255);">.</span></div></div><div= ><br /></div><div>BTW: The link referring to chapter 7 is broken.=C2=A0</di= v><div><br /></div><div id=3D"signature_old"><div id=3D"x75154ce80e9e4bf"> <div class=3D"WordSection1"> <div id=3D"xb71224f920234978acc74f4d23143069"><div class=3D"WordSection1"><= p class=3D"MsoNormal"><font face=3D"Tahoma"><font size=3D"3" style=3D"font-= size: 12pt;">Kind r</font><span style=3D"font-size: 12pt;">egards</span></f= ont></p><p class=3D"MsoNormal"><font size=3D"3" style=3D"font-size: 12pt;"= face=3D"Tahoma"><br /></font></p><p class=3D"MsoNormal"><font size=3D"3" st= yle=3D"font-size: 12pt;" face=3D"Tahoma">Andrew=C2=A0</font></p></div></div= > </div> </div></div><div><br /></div> </blockquote></div> </body></html> --------=_MB15379295-79C3-4E7D-BA3E-C6F662EE3B38--

2 1

Gluster issue with /var/lib/glusterd/peers/<ip> file
by Mike DePaulo 03 Jul '17

03 Jul '17

Hi everyone, I have ovirt 4.1.1/4.1.2 running on 3 hosts with a gluster hosted engine. I was working on setting up a network for gluster storage and migration. The addresses for it will be 10.0.20.x, rather than 192.168.1.x for the management network. However, I switched gluster storage and migration back over to the management network. I updated and rebooted one of my hosts (death-star, 10.0.20.52) and on reboot, the glusterd service would start, but wouldn't seem to work. The engine webgui reported that its bricks were down, and commands like this would fail: [root@death-star glusterfs]# gluster pool list pool list: failed [root@death-star glusterfs]# gluster peer status peer status: failed Upon further investigation, I had under /var/lib/glusterd/peers/ the 2 existing UUID files, plus a new 3rd one: [root@death-star peers]# cat 10.0.20.53 uuid=00000000-0000-0000-0000-000000000000 state=0 hostname1=10.0.20.53 I moved that file out of there, restarted glusterd, and now gluster is working again. I am guessing that this is a bug. Let me know if I should attach other log files; I am not sure which ones. And yes, 10.0.20.53 is the IP of one of the other hosts. -Mike

4 3

Other portals work, user portal experiences console errors
by Sophia Valentine 03 Jul '17

03 Jul '17

Hi all! I installed the nightly from the repo on CentOS 7.0. I currently have an issue where visiting the user portal triggers the following errors in the browser console. I believe that I will need to compile the engine from source due to the current source being compacted, thus obscuring the stacktrace. If that is needed, can I generate an RPM with the debug build I create (might need some help with this, if that's okay)? I'm hoping it's a "known error" and that there's a simple fix. Would love to get to the bottom of this! Thanks. Stacktrace below: Mon Jul 03 09:13:51 GMT+100 2017 com.gwtplatform.mvp.client.presenter.slots.LegacySlotConvertor SEVERE: Warning: You're using an untyped slot! Untyped slots are dangerous! Please upgrade your slots using the Arcbee's easy upgrade tool at https://arcbees.github.io/gwtp-slot-upgrader uGc @ userportal-0.js:12779 userportal-0.js:12779 Mon Jul 03 09:13:51 GMT+100 2017 SEVERE: Uncaught exception com.google.web.bindery.event.shared.UmbrellaException: 2 exceptions caught: Adding non GroupedTabData; Adding non GroupedTabData at Unknown.lp(userportal-0.js) at Unknown.xp(userportal-0.js) at Unknown.dQ(userportal-0.js) at Unknown.EP(userportal-0.js) at Unknown.HP(userportal-0.js) at Unknown.YP(userportal-0.js) at Unknown.Omd(userportal-0.js) at Unknown.Und(userportal-28.js) at Unknown.bmd(userportal-0.js) at Unknown.mnd(userportal-28.js) at Unknown.amd(userportal-0.js) at Unknown.Rqo(userportal-2.js) at Unknown.dro(userportal-2.js) at Unknown.yq(userportal-0.js) at Unknown.Dq(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(userportal-2.js) at Unknown.userportal.__installRunAsyncCode(https://vmengine.x.com/ovirt-engin… at Unknown.__gwtInstallCode(userportal-0.js) at Unknown.mr(userportal-0.js) at Unknown.Kr(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(https://vmengine.x.com/ovirt-engine/userportal/deferredjs… Suppressed: java.lang.RuntimeException: Adding non GroupedTabData at Unknown.kp(userportal-0.js) at Unknown.up(userportal-0.js) at Unknown.wp(userportal-0.js) at Unknown.XLk(userportal-2.js) at Unknown.w2j(userportal-28.js) at Unknown.Rnd(userportal-28.js) at Unknown.znd(userportal-28.js) at Unknown.Bnd(userportal-28.js) at Unknown.EP(userportal-0.js) at Unknown.HP(userportal-0.js) at Unknown.YP(userportal-0.js) at Unknown.Omd(userportal-0.js) at Unknown.Und(userportal-28.js) at Unknown.bmd(userportal-0.js) at Unknown.mnd(userportal-28.js) at Unknown.amd(userportal-0.js) at Unknown.Rqo(userportal-2.js) at Unknown.dro(userportal-2.js) at Unknown.yq(userportal-0.js) at Unknown.Dq(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(userportal-2.js) at Unknown.userportal.__installRunAsyncCode(https://vmengine.x.com/ovirt-engin… at Unknown.__gwtInstallCode(userportal-0.js) at Unknown.mr(userportal-0.js) at Unknown.Kr(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(https://vmengine.x.com/ovirt-engine/userportal/deferredjs… Caused by: java.lang.RuntimeException: Adding non GroupedTabData at Unknown.kp(userportal-0.js) at Unknown.up(userportal-0.js) at Unknown.wp(userportal-0.js) at Unknown.XLk(userportal-2.js) at Unknown.w2j(userportal-28.js) at Unknown.Rnd(userportal-28.js) at Unknown.znd(userportal-28.js) at Unknown.Bnd(userportal-28.js) at Unknown.EP(userportal-0.js) at Unknown.HP(userportal-0.js) at Unknown.YP(userportal-0.js) at Unknown.Omd(userportal-0.js) at Unknown.Und(userportal-28.js) at Unknown.bmd(userportal-0.js) at Unknown.mnd(userportal-28.js) at Unknown.amd(userportal-0.js) at Unknown.Rqo(userportal-2.js) at Unknown.dro(userportal-2.js) at Unknown.yq(userportal-0.js) at Unknown.Dq(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(userportal-2.js) at Unknown.userportal.__installRunAsyncCode(https://vmengine.x.com/ovirt-engin… at Unknown.__gwtInstallCode(userportal-0.js) at Unknown.mr(userportal-0.js) at Unknown.Kr(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(https://vmengine.x.com/ovirt-engine/userportal/deferredjs… uGc @ userportal-0.js:12779 userportal-0.js:12779 Mon Jul 03 09:13:51 GMT+100 2017 remote SEVERE: Uncaught exception com.google.web.bindery.event.shared.UmbrellaException: 2 exceptions caught: Adding non GroupedTabData; Adding non GroupedTabData at Unknown.lp(userportal-0.js) at Unknown.xp(userportal-0.js) at Unknown.dQ(userportal-0.js) at Unknown.EP(userportal-0.js) at Unknown.HP(userportal-0.js) at Unknown.YP(userportal-0.js) at Unknown.Omd(userportal-0.js) at Unknown.Und(userportal-28.js) at Unknown.bmd(userportal-0.js) at Unknown.mnd(userportal-28.js) at Unknown.amd(userportal-0.js) at Unknown.Rqo(userportal-2.js) at Unknown.dro(userportal-2.js) at Unknown.yq(userportal-0.js) at Unknown.Dq(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(userportal-2.js) at Unknown.userportal.__installRunAsyncCode(https://vmengine.x.com/ovirt-engin… at Unknown.__gwtInstallCode(userportal-0.js) at Unknown.mr(userportal-0.js) at Unknown.Kr(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(https://vmengine.x.com/ovirt-engine/userportal/deferredjs… Suppressed: java.lang.RuntimeException: Adding non GroupedTabData at Unknown.kp(userportal-0.js) at Unknown.up(userportal-0.js) at Unknown.wp(userportal-0.js) at Unknown.XLk(userportal-2.js) at Unknown.w2j(userportal-28.js) at Unknown.Rnd(userportal-28.js) at Unknown.znd(userportal-28.js) at Unknown.Bnd(userportal-28.js) at Unknown.EP(userportal-0.js) at Unknown.HP(userportal-0.js) at Unknown.YP(userportal-0.js) at Unknown.Omd(userportal-0.js) at Unknown.Und(userportal-28.js) at Unknown.bmd(userportal-0.js) at Unknown.mnd(userportal-28.js) at Unknown.amd(userportal-0.js) at Unknown.Rqo(userportal-2.js) at Unknown.dro(userportal-2.js) at Unknown.yq(userportal-0.js) at Unknown.Dq(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(userportal-2.js) at Unknown.userportal.__installRunAsyncCode(https://vmengine.x.com/ovirt-engin… at Unknown.__gwtInstallCode(userportal-0.js) at Unknown.mr(userportal-0.js) at Unknown.Kr(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(https://vmengine.x.com/ovirt-engine/userportal/deferredjs… Caused by: java.lang.RuntimeException: Adding non GroupedTabData at Unknown.kp(userportal-0.js) at Unknown.up(userportal-0.js) at Unknown.wp(userportal-0.js) at Unknown.XLk(userportal-2.js) at Unknown.w2j(userportal-28.js) at Unknown.Rnd(userportal-28.js) at Unknown.znd(userportal-28.js) at Unknown.Bnd(userportal-28.js) at Unknown.EP(userportal-0.js) at Unknown.HP(userportal-0.js) at Unknown.YP(userportal-0.js) at Unknown.Omd(userportal-0.js) at Unknown.Und(userportal-28.js) at Unknown.bmd(userportal-0.js) at Unknown.mnd(userportal-28.js) at Unknown.amd(userportal-0.js) at Unknown.Rqo(userportal-2.js) at Unknown.dro(userportal-2.js) at Unknown.yq(userportal-0.js) at Unknown.Dq(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(userportal-2.js) at Unknown.userportal.__installRunAsyncCode(https://vmengine.x.com/ovirt-engin… at Unknown.__gwtInstallCode(userportal-0.js) at Unknown.mr(userportal-0.js) at Unknown.Kr(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.Zq(userportal-0.js) at Unknown.ar(userportal-0.js) at Unknown.eval(userportal-0.js) at Unknown.anonymous(https://vmengine.x.com/ovirt-engine/userportal/deferredjs… uGc @ userportal-0.js:12779 -- Sophia Valentine System administrator https://apertron.net

4 6

Gluster storage network not being used for Gluster
by Mike DePaulo 03 Jul '17

03 Jul '17

Hi, I configured a "Gluster storage" network, but it doesn't look like it is being used for Gluster. Specifically, the switch's LEDs are not blinking, and the hosts' "Total Tx" and "Total Rx" counts are not changing (and they're tiny, under 1 MB.) The management network must still be being used. I have 3 hosts running oVirt Node 4.1.x. I set them up via the gluster hosted engine. The gluster storage network is 10.0.20.x. These are the contents of /var/lib/glusterd/peers: [root@centerpoint peers]# cat 8a83fddd-df7e-4e3b-9fc7-ca1c9bf9deaa uuid=8a83fddd-df7e-4e3b-9fc7-ca1c9bf9deaa state=3 hostname1=death-star.ad.depaulo.org hostname2=death-star hostname3=192.168.1.52 hostname4=10.0.20.52 [root@centerpoint peers]# cat b6b96427-a0dd-47ff-b3e0-038eb0967fb9 uuid=b6b96427-a0dd-47ff-b3e0-038eb0967fb9 state=3 hostname1=starkiller-base.ad.depaulo.org hostname2=starkiller-base hostname3=192.168.1.53 Thanks in advance, -Mike

2 1

Best way of doing complete stop of HCI environment?
by Gianluca Cecchi 03 Jul '17

03 Jul '17

Any recommendations in case I have to take down a site for maintenance? Thanks, Gianluca

2 1

vdsm changing disk scheduler when starting, configurable?
by Darrell Budic 03 Jul '17

03 Jul '17

It seems vdsmd under 4.1.x (or something under it’s control) changes the disk schedulers when it starts or a host node is activated, and I’d like to avoid this. Is it preventable? Or configurable anywhere? This was probably happening under earlier version, but I just noticed it while upgrading some converged boxes today. It likes to set deadline, which I understand is the RHEL default for centos 7 on non SATA disks. But I’d rather have NOOP on my SSDs because SSDs, and NOOP on my SATA spinning platters because ZFS does it’s own scheduling, and running anything other than NOOP can cause increased CPU utilization for no gain. It’s also fighting ZFS, which tires to set NOOP on whole disks it controls, and my kernel command line setting. Thanks, -Darrell

2 1

vdsm (4.1) restarts glusterd when activating a node, even if it's already running
by Darrell Budic 02 Jul '17

02 Jul '17

Upgrading some nodes today, and noticed that vdsmd restarts glusterd on a node when it activates it. This is causing a short break in healing when the shd gets disconnected, forcing some extra healing when the healing process reports “Transport Endpoint Disconnected” (N/A in the ovirt gui). This is on a converged cluster (3 nodes, gluster replica volume across all 3, ovirt-engine running elsewhere). Centos 7 install, just upgraded to Ovirt 4.1.2, running cluster 3.10 from the Centos SIG. The process I’m observing: Place a node into maintenance via GUI Update node from command line Reboot node (kernel update) Watch gluster heal itself after reboot Activate node in GUI gluster is completely stopped on this node gluster is started on this node healing begins again, but isn’t working “gluster vol heal XXXX info” reports this node’s information not available because “Transport endpoint not connected”. This clears up in 5-10 minutes, then volume heals normally Someone with a similar setup want to check this and see if it’s something specific to my nodes, or just a general problem with the way it’s restarting gluster? Looking for a little confirmation before I file a bug report on it. Or a dev want to comment on why it stops and starts gluster, instead of a restart which would presumably leave the brick processes and shd running and not causing this effect? Thanks, -Darrell

1 0

Storage, extend or new lun ?
by Enrico Becchetti Gmail 02 Jul '17

02 Jul '17

Dear All, I've oVirt 3.5.3-1-1.el6 with two kind of storage , NFS and Fibre Channel. Each Hypervisor has HBA controller and Data CLutser has four Storage named: DATA_FC, DATA_NFS, EXPORT and ISO-DOMAIN. Anybody know how can I extend a DATA_FC ? Which is the best practies ? Extend LUN from HP MSA controller or adding a new lun ? if I extend lun inside HP MSA oVirt see the new size ? Enrico Thanks a lot. Best Regards

2 3

Cannot find master domain
by Iman Darabi 02 Jul '17

02 Jul '17

hi. i moved my host to maintenance mode and upgrade it. then restarted server. after restarting, i activated server but the data domain is inactive and i get the following error: "Cannot find master domain: u'spUUID=9a1584cf-81bb-4ce8-975f-659e643a14b5, msdUUID=193072f2-9c4a-405c-86a8-c4b036413171'", 'code': 304 The output of "multipath -v2" is as follows: Jul 01 12:38:34 | sdb: emc prio: path not correctly configured for failover Jul 01 12:38:34 | sdc: emc prio: path not correctly configured for failover Jul 01 12:38:34 | 3600508b1001cbeb7dc20cfc250a2e506: ignoring map Jul 01 12:38:34 | sdb: emc prio: path not correctly configured for failover Jul 01 12:38:34 | sdc: emc prio: path not correctly configured for failover Jul 01 12:38:34 | DM message failed [fail_if_no_path] reject: 3600601604d003a00036edddd268de611 undef DGC ,VNX5400WDVR size=2.0T features='0' hwhandler='1 emc' wp=undef |-+- policy='service-time 0' prio=0 status=undef | |- 12:0:0:16384 sdb 8:16 undef faulty running | `- 12:0:1:16384 sdc 8:32 undef faulty running |-+- policy='service-time 0' prio=50 status=undef | `- 11:0:1:0 sde 8:64 undef ready running `-+- policy='service-time 0' prio=10 status=undef `- 11:0:0:0 sdd 8:48 undef ready running thanks. -- R&D expert at Ferdowsi University of Mashhadhttps://ir.linkedin.com/in/ imandarabi <https://www.linkedin.com/profile/public-profile-settings?trk=prof-edit-edit…>

2 1

import data domain
by Iman Darabi 02 Jul '17

02 Jul '17

hi. what happen if we destroy a data domain and then again import it? do we lost all vm's and it's configurations? -- R&D expert at Ferdowsi University of Mashhad https://ir.linkedin.com/in/imandarabi <https://www.linkedin.com/profile/public-profile-settings?trk=prof-edit-edit…>

2 1

Recovering hosted-engine
by Andrew Dent 02 Jul '17

02 Jul '17

--------=_MB617458AF-4FCC-4AB6-8A34-3338D99C6BB8 Content-Type: text/plain; format=flowed; charset=utf-8 Content-Transfer-Encoding: quoted-printable Hi A couple of questions about hosted-engine recovery. Part way through this URL, in the section "Workflow for Restoring the=20 Self-Hosted Engine Environment" http://www.ovirt.org/documentation/self-hosted/chap-Backing_up_and_Restorin= g_an_EL-Based_Self-Hosted_Environment/ it looks like once the hosted-engine is recovered on Host 1, the VMs on=20 Host 2 and 3 will be running, but not accessible to the recovered Hosted=20 Engine. Is that correct? If so, how to you remove host 2 and host 3 from the environment, then=20 add back in again while keeping the VMs running? Host 2 and Host 3 are not recoverable in their current state. These=20 hosts need to be removed from the environment, and then added again to=20 the environment using the hosted-engine deployment script. For more=20 information on these actions, see the Removing Non-Operational Hosts=20 from a Restored Self-Hosted Engine Environment section below and Chapter=20 7: Installing Additional Hosts to a Self-Hosted Environment=20 <http://www.ovirt.org/documentation/self-hosted/chap-Backing_up_and_Restori= ng_an_EL-Based_Self-Hosted_Environment/chap-Installing_Additional_Hosts_to_= a_Self-Hosted_Environment>. BTW: The link referring to chapter 7 is broken. Kind regards Andrew --------=_MB617458AF-4FCC-4AB6-8A34-3338D99C6BB8 Content-Type: text/html; charset=utf-8 Content-Transfer-Encoding: quoted-printable <?xml version=3D"1.0" encoding=3D"utf-16"?><html><head> <style id=3D"signatureStyle"></style> <style></style> </head> <body><div>Hi</div><div><br /></div><div>A couple of questions about hosted= -engine recovery.</div><div>Part way through this URL, in the section "Work= flow for Restoring the Self-Hosted Engine Environment"=C2=A0</div><div><a h= ref=3D"http://www.ovirt.org/documentation/self-hosted/chap-Backing_up_and_R= estoring_an_EL-Based_Self-Hosted_Environment/">http://www.ovirt.org/documen= tation/self-hosted/chap-Backing_up_and_Restoring_an_EL-Based_Self-Hosted_En= vironment/</a></div><div>it looks like once the hosted-engine is recovered= on Host 1, the VMs on Host 2 and 3 will be running, but not accessible to t= he recovered Hosted Engine.=C2=A0</div><div>Is that correct?</div><div>If s= o, how to you remove host 2 and host 3 from the environment, then add back= in again while keeping the VMs running?</div><div><br /></div><div><div> <code style=3D"box-sizing: border-box; font-family: Menlo, Monaco, Consolas= , 'Courier New', monospace; font-size: 14.4px; padding: 2px 4px; color: rgb= (199, 37, 78); border-radius: 4px; font-variant-ligatures: normal; orphans: = 2; widows: 2; background-color: rgb(249, 242, 244);">Host 2</code><span st= yle=3D"color: rgb(51, 51, 51); font-family: 'Source Sans Pro', 'Open Sans', = 'Helvetica Neue', Helvetica, Arial, sans-serif; font-variant-ligatures: no= rmal; orphans: 2; widows: 2; background-color: rgb(255, 255, 255);">=C2=A0a= nd=C2=A0</span><code style=3D"box-sizing: border-box; font-family: Menlo, M= onaco, Consolas, 'Courier New', monospace; font-size: 14.4px; padding: 2px= 4px; color: rgb(199, 37, 78); border-radius: 4px; font-variant-ligatures: n= ormal; orphans: 2; widows: 2; background-color: rgb(249, 242, 244);">Host 3= </code><span style=3D"color: rgb(51, 51, 51); font-family: 'Source Sans Pro= ', 'Open Sans', 'Helvetica Neue', Helvetica, Arial, sans-serif; font-varian= t-ligatures: normal; orphans: 2; widows: 2; background-color: rgb(255, 255, = 255);">=C2=A0are not recoverable in their current state. These hosts need= to be removed from the environment, and then added again to the environment = using the hosted-engine deployment script. For more information on these a= ctions, see the Removing Non-Operational Hosts from a Restored Self-Hosted= Engine Environment section below and=C2=A0</span><a href=3D"http://www.ovir= t.org/documentation/self-hosted/chap-Backing_up_and_Restoring_an_EL-Based_S= elf-Hosted_Environment/chap-Installing_Additional_Hosts_to_a_Self-Hosted_En= vironment" style=3D"box-sizing: border-box; color: rgb(97, 182, 14); text-d= ecoration: none; font-family: 'Source Sans Pro', 'Open Sans', 'Helvetica Ne= ue', Helvetica, Arial, sans-serif; font-variant-ligatures: normal; orphans: = 2; widows: 2; background-color: rgb(255, 255, 255);">Chapter 7: Installing = Additional Hosts to a Self-Hosted Environment</a><span style=3D"color: rgb= (51, 51, 51); font-family: 'Source Sans Pro', 'Open Sans', 'Helvetica Neue'= , Helvetica, Arial, sans-serif; font-variant-ligatures: normal; orphans: 2; = widows: 2; background-color: rgb(255, 255, 255);">.</span></div></div><div= ><br /></div><div>BTW: The link referring to chapter 7 is broken.=C2=A0</di= v><div><br /></div><div id=3D"signature_old"><div id=3D"x75154ce80e9e4bf"> <div class=3D"WordSection1"> <div id=3D"xb71224f920234978acc74f4d23143069"><div class=3D"WordSection1"><= p class=3D"MsoNormal"><font face=3D"Tahoma"><font size=3D"3" style=3D"font-= size: 12pt;">Kind r</font><span style=3D"font-size: 12pt;">egards</span></f= ont></p><p class=3D"MsoNormal"><font size=3D"3" style=3D"font-size: 12pt;"= face=3D"Tahoma"><br /></font></p><p class=3D"MsoNormal"><font size=3D"3" st= yle=3D"font-size: 12pt;" face=3D"Tahoma">Andrew=C2=A0</font></p></div></div= > </div> </div></div><div><br /></div> </body></html> --------=_MB617458AF-4FCC-4AB6-8A34-3338D99C6BB8--

1 0

oVirt Node update not updating kernel, glibc, etc
by Mike DePaulo 02 Jul '17

02 Jul '17

Hi, I installed 3 ovirt 4.1.1 nodes in early May. Today used oVirt's webgui to update ("Upgrade") 2 of them. They are both reporting oVirt Node 4.1.2 & vdsm-4.19.15-1.el7.centos now. However, it appears that the kernel was not updated: [root@death-star peers]# uname -a Linux death-star 3.10.0-514.16.1.el7.x86_64 #1 SMP Wed Apr 12 15:04:24 UTC 2017 x86_64 x86_64 x86_64 GNU/Linux And neither was glibc The installed version is still 2.17-157.el7_3.1 rather than 2.17-157.el7_3.4 . The following lines were appended to /var/log/yum.log: Jul 01 18:47:49 Installed: ovirt-node-ng-image-4.1.2-1.el7.centos.noarch Jul 01 18:50:27 Installed: ovirt-node-ng-image-update-4.1.2-1.el7.centos.noarch Jul 01 18:50:27 Erased: ovirt-node-ng-image-update-placeholder-4.1.1.1-1.el7.centos.noarch Thanks in advance, -Mike

1 0

Re: [ovirt-users] [ovirt-devel] problem about vm in ovirt node can ping node, but cannot ping gateway or the third host in LAN
by Edward Haas 01 Jul '17

01 Jul '17

If I understood correctly, you are using a nested solution where the node is itself a VM. If this is the case, you may have a security feature active on the physical host/node. In oVirt we have the default filter which allows only a single source mac to exit the vNIC, but you disabled it. I guess you should have something similar on the upper node. Please note that such topics fit the user list, not devel. Thanks, Edy. On Fri, Jun 30, 2017 at 1:46 PM, pengyixiang <yxpengi386(a)163.com> wrote: > hi, everyone > > I am a new bird in ovirt, and I transplate ovirt node to debian > jessie(customed) system, it's work well now, then we create vm, use default > nic1, like this: > > in vm, we ping node, it's ok; and in node, we ping vm, it's ok too; > then in node, we ping gatway or other computer in the lan, it's ok too; > > but when in vm, we ping gatway or other computer in the lan, it's not ok, > why is this? > > > >>> next is some test infomation: > > 1) after vm up, vnet0 is created, and use : > > # brctl show ovirtmgmt > > we get this: > > bridge name bridge id STP enabled interfaces > ovirtmgmt 8000.000c29e3037e no eth0 > > vnet0 > > > 2) then we test network in three host in the same time > > in vm > > # tcpdump -i eth0 arp > > vm send request > > vm not recv reply > > # ping hostA > > > in node(vm in) > > # tcpdump -i vnet0 arp > > vnet0 send request > > vnet0 not recv reply > > > in third host in the lan(hostA) > > # tcpdump -i eth0 arp > > eth0 recv request > > eth0 send reply > > > problem like this: > > > why is this, do I lost some configurations ? > > > ovirtmgmt configuration: > > > vnet info:(node installed in ESXI) > > > > > Look forward to your reply > > > Have a nice day > > -- > > > _______________________________________________ > Devel mailing list > Devel(a)ovirt.org > http://lists.ovirt.org/mailman/listinfo/devel >

1 0

HostedEngine VM not visible, but running
by cmc 30 Jun '17

30 Jun '17

Hi, I've migrated from a bare-metal engine to a hosted engine. There were no errors during the install, however, the hosted engine did not get started. I tried running: hosted-engine --status on the host I deployed it on, and it returns nothing (exit code is 1 however). I could not ping it either. So I tried starting it via 'hosted-engine --vm-start' and it returned: Virtual machine does not exist But it then became available. I logged into it successfully. It is not in the list of VMs however. Any ideas why the hosted-engine commands fail, and why it is not in the list of virtual machines? Thanks for any help, Cam

7 46

Sound Device Custom Property
by Mauricio Perez 30 Jun '17

30 Jun '17

This is a multipart message in MIME format. ------=_NextPart_000_0063_01D2F1A4.D9A2A050 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Hello Everyone, I am trying to modify a VM sound device sub element to <codec type='micro'/>. I understand the only way to perform this is by using a before vm start vdsm hook to define custom property. Can someone please guide to setting this up. * How would I define it in the engine config? * How do I create the hooking module? * Is there a source to find pre created hooking modules? Thank You All!! ------=_NextPart_000_0063_01D2F1A4.D9A2A050 Content-Type: text/html; charset="us-ascii" Content-Transfer-Encoding: quoted-printable <html xmlns:v=3D"urn:schemas-microsoft-com:vml" = xmlns:o=3D"urn:schemas-microsoft-com:office:office" = xmlns:w=3D"urn:schemas-microsoft-com:office:word" = xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml" = xmlns=3D"http://www.w3.org/TR/REC-html40"><head><META = HTTP-EQUIV=3D"Content-Type" CONTENT=3D"text/html; = charset=3Dus-ascii"><meta name=3DGenerator content=3D"Microsoft Word 15 = (filtered medium)"><style></style></head><body lang=3DEN-US = link=3D"#0563C1" vlink=3D"#954F72"><div class=3DWordSection1><p = class=3DMsoNormal>Hello Everyone,<o:p></o:p></p><p = class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>I am trying = to modify a VM sound device sub element to  <codec = type=3D'micro'/>. I understand the only way to perform this is by = using a before vm start vdsm hook to define custom property. Can someone = please guide to setting this up.<o:p></o:p></p><p = class=3DMsoListParagraph style=3D'text-indent:-.25in;mso-list:l0 level1 = lfo1'><![if !supportLists]><span style=3D'font-family:Symbol'><span = style=3D'mso-list:Ignore'>·<span style=3D'font:7.0pt "Times New = Roman"'>         = </span></span></span><![endif]>How would I define it in the engine = config?<o:p></o:p></p><p class=3DMsoListParagraph = style=3D'text-indent:-.25in;mso-list:l0 level1 lfo1'><![if = !supportLists]><span style=3D'font-family:Symbol'><span = style=3D'mso-list:Ignore'>·<span style=3D'font:7.0pt "Times New = Roman"'>         = </span></span></span><![endif]>How do I create the hooking = module?<o:p></o:p></p><p class=3DMsoListParagraph = style=3D'text-indent:-.25in;mso-list:l0 level1 lfo1'><![if = !supportLists]><span style=3D'font-family:Symbol'><span = style=3D'mso-list:Ignore'>·<span style=3D'font:7.0pt "Times New = Roman"'>         = </span></span></span><![endif]>Is there a source to find pre created = hooking modules?<o:p></o:p></p><p = class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>Thank You = All!!<o:p></o:p></p></div></body></html> ------=_NextPart_000_0063_01D2F1A4.D9A2A050--

1 0

moVirt 2.0 released!
by Filip Krepinsky 30 Jun '17

30 Jun '17

Hello everyone, moVirt 2.0 has just been released and should arrive to your devices soon! You can also get the apk from our GitHub [1]. The main feature of this release is managing multiple oVirt installations + many other cool features [2]. Thanks everybody who helped with testing and especially big thanks to Shira who gave us lots of valuable input. Have a nice day Filip [1]: https://github.com/oVirt/moVirt/releases/tag/v2.0 [2]: https://github.com/oVirt/moVirt/wiki/Changelog

1 0

Help! No VMs start after reboot of cluster
by cmc 30 Jun '17

30 Jun '17

Hi, I restarted my 3 host cluster after setting it into global maintenance mode and then shutting down all of the nodes and then bringing them up again. I moved it out of global maintenance mode and no VM is running, including the hosted engine. Any help greatly appreciated! Thanks, Cam

3 5

Re: [ovirt-users] Frustration defines the deployment of Hosted Engine
by Karli Sjöberg 30 Jun '17

30 Jun '17

11 16

vm shutdown long delay is a problem for users of pools
by Paul 30 Jun '17

30 Jun '17

This is a multipart message in MIME format. ------=_NextPart_000_0079_01D2EB83.89CE5690 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Hi, Shutting down VM's in the portal with the red downfacing arrow takes quite some time (about 90 seconds). I read this is mainly due to a 60 second delay in the ovirt-guest-agent. I got used to right-click and use "power off" instead of "shutdown", which is fine. My users make use of VM in a VM-pool. They get assigned a VM and after console disconnect the VM shuts down (default recommended behavior). My issue is that the users stays assigned to this VM for the full 90 seconds and cannot do "power off". Suppose he disconnected by accident, he has to wait 90 seconds until he is assigned to the pool again until he can connect to another VM. My questions are: - Is it possible to decrease the time delay of a VM shutdown? 90 seconds is quite a lot, 10 seconds should be enough - Is it possible for normal users to use "power off"? - Is it possible to "unallocate" the user from a VM if it is powering down? So he can allocate another VM Kind regards, Paul ------=_NextPart_000_0079_01D2EB83.89CE5690 Content-Type: text/html; charset="us-ascii" Content-Transfer-Encoding: quoted-printable <html xmlns:v=3D"urn:schemas-microsoft-com:vml" = xmlns:o=3D"urn:schemas-microsoft-com:office:office" = xmlns:w=3D"urn:schemas-microsoft-com:office:word" = xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml" = xmlns=3D"http://www.w3.org/TR/REC-html40"><head><meta = http-equiv=3DContent-Type content=3D"text/html; = charset=3Dus-ascii"><meta name=3DGenerator content=3D"Microsoft Word 15 = (filtered medium)"><style></style></head><body lang=3DNL = link=3D"#0563C1" vlink=3D"#954F72"><div class=3DWordSection1><p = class=3DMsoNormal><span lang=3DEN-US = style=3D'color:#1F497D'>Hi,<o:p></o:p></span></p><p = class=3DMsoNormal><span lang=3DEN-US style=3D'color:#1F497D'>Shutting = down VM’s in the portal with the red downfacing arrow takes quite = some time (about 90 seconds). I read this is mainly due to a 60 second = delay in the ovirt-guest-agent. I got used to right-click and use = “power off” instead of “shutdown”, which is = fine.<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-US = style=3D'color:#1F497D'><o:p> </o:p></span></p><p = class=3DMsoNormal><span lang=3DEN-US style=3D'color:#1F497D'>My users = make use of VM in a VM-pool. They get assigned a VM and after console = disconnect the VM shuts down (default recommended behavior). My issue is = that the users stays assigned to this VM for the full 90 seconds and = cannot do “power off”. Suppose he disconnected by accident, = he has to wait 90 seconds until he is assigned to the pool again until = he can connect to another VM. <o:p></o:p></span></p><p = class=3DMsoNormal><span lang=3DEN-US = style=3D'color:#1F497D'><o:p> </o:p></span></p><p = class=3DMsoNormal><span lang=3DEN-US style=3D'color:#1F497D'>My = questions are:<o:p></o:p></span></p><p class=3DMsoListParagraph = style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo1'><![if = !supportLists]><span lang=3DEN-US style=3D'color:#1F497D'><span = style=3D'mso-list:Ignore'>-<span style=3D'font:7.0pt "Times New = Roman"'>          = </span></span></span><![endif]><span lang=3DEN-US = style=3D'color:#1F497D'>Is it possible to decrease the time delay of a = VM shutdown? 90 seconds is quite a lot, 10 seconds should be = enough<o:p></o:p></span></p><p class=3DMsoListParagraph = style=3D'text-indent:-18.0pt;mso-list:l0 level1 lfo1'><![if = !supportLists]><span lang=3DEN-US style=3D'color:#1F497D'><span = style=3D'mso-list:Ignore'>-<span style=3D'font:7.0pt "Times New = Roman"'>          = </span></span></span><![endif]><span lang=3DEN-US = style=3D'color:#1F497D'>Is it possible for normal users to use = “power off”?<o:p></o:p></span></p><p = class=3DMsoListParagraph style=3D'text-indent:-18.0pt;mso-list:l0 level1 = lfo1'><![if !supportLists]><span lang=3DEN-US = style=3D'color:#1F497D'><span style=3D'mso-list:Ignore'>-<span = style=3D'font:7.0pt "Times New = Roman"'>          = </span></span></span><![endif]><span lang=3DEN-US = style=3D'color:#1F497D'>Is it possible to “unallocate” the = user from a VM if it is powering down? So he can allocate another = VM<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-US = style=3D'color:#1F497D'><o:p> </o:p></span></p><p = class=3DMsoNormal><span lang=3DEN-US style=3D'color:#1F497D'>Kind = regards,<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-US = style=3D'color:#1F497D'><o:p> </o:p></span></p><p = class=3DMsoNormal><span lang=3DEN-US = style=3D'color:#1F497D'>Paul<o:p></o:p></span></p></div></body></html> ------=_NextPart_000_0079_01D2EB83.89CE5690--

3 3

Unable to rename disks via REST API
by Bruno Rodriguez 30 Jun '17

30 Jun '17

Hello everyone, I'm having some problems about renaming some disks (setting a different alias, name or description) for VMs disks created from a template. When I get this URL https://ovirt-manager/ovirt-engine/api/disks/0123 I can see are the methods sparsify, export, move and copy. I tried to POST the following XML to the previous URL with no result (as expected, it won't work) <disk> <alias>my_machine_Disk1</alias> </disk> I'm quite sure I'm thinking about it in a wrong way (as usual). Any help would be welcome... Thank you in advance -- Bruno Rodríguez Rodríguez *Port d'Informació Científica (PIC)*

3 9

[ANN] oVirt 4.1.3 Third Release Candidate is now available
by Sandro Bonazzola 29 Jun '17

29 Jun '17

The oVirt Project is pleased to announce the availability of the Third Release Candidate of oVirt 4.1.3 for testing, as of June 22nd, 2017 This is pre-release software. Please take a look at our community page[1] to know how to ask questions and interact with developers and users. All issues or bugs should be reported via oVirt Bugzilla[2]. This pre-release should not to be used in production. This update is the first release candidate of the third in a series of stabilization updates to the 4.1 series. 4.1.3 brings more than 45 enhancements and more than 220 bugfixes, including more than 120 high or urgent severity fixes, on top of oVirt 4.1 series This release is available now for: * Fedora 24 (tech preview) * Red Hat Enterprise Linux 7.3 or later * CentOS Linux (or similar) 7.3 or later This release supports Hypervisor Hosts running: * Red Hat Enterprise Linux 7.3 or later * CentOS Linux (or similar) 7.3 or later * oVirt Node 4.1 * Fedora 24 (tech preview) See the release notes draft [3] for installation / upgrade instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is already available - oVirt Live is already available[4] - oVirt Node is already available[4] We are addressing compose issues for above components which are missing ansible 2.3 and latest fluentd builds from CentOS SIGs. Additional Resources: * Read more about the oVirt 4.1.3 release highlights: http://www.ovirt.org/release/4.1.3/ * Get more oVirt Project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] https://www.ovirt.org/community/ [2] https://bugzilla.redhat.com/enter_bug.cgi?classification=oVirt [3] http://www.ovirt.org/release/4.1.3/ [4] resources.ovirt.org/pub/ovirt-4.1-pre/iso/ -- SANDRO BONAZZOLA ASSOCIATE MANAGER, SOFTWARE ENGINEERING, EMEA ENG VIRTUALIZATION R&D Red Hat EMEA <https://www.redhat.com/> <https://red.ht/sig> TRIED. TESTED. TRUSTED. <https://redhat.com/trusted>

2 2

moVirt 2.0 RC 1 released!
by Filip Krepinsky 29 Jun '17

29 Jun '17

Hia, the first RC of moVirt 2.0 has been released! You can get it from our GitHub [1]; the play store will be upgraded after considered stable. The main feature of this release is a support for managing multiple oVirt installations from one moVirt. Other changes: - actions/lists/dashboard are now filtered by selecting accounts/clusters in the left drawer - event lists now correctly working for single vm, host, etc.. - better syncing and network detection - cleaner ui design and connection settings - enhanced security and support for certificates (import from file) - sorting and filtering made more usable - more descriptive errors - other small enhancements and bug fixes We would greatly appreciate if you could try it and share your feedback with us. [2] Let us know about any suggestions you might have; and as usual, patches are also welcome :) Have a great day Filip [1]: https://github.com/oVirt/moVirt/releases/download/v2.0-rc1/moVirt-release.a… [2]: https://github.com/oVirt/moVirt

4 5

Moving thin provisioned disks question
by Gianluca Cecchi 29 Jun '17

29 Jun '17

Hello, I have a storage domain that I have to empty, moving its disks to another storage domain, Both source and target domains are iSCSI What is the behavior in case of preallocated and thin provisioned disk? Are they preserved with their initial configuration? Suppose I have one 500Gb thin provisioned disk Why can I indirectly see that the actual size is 300Gb only in Snapshots tab --> Disks of its VM ? Thanks, Gianluca

4 10

Ovirt installation planning question
by Alan Bunch 28 Jun '17

28 Jun '17

--_000_C46E817F004EDF47A188C55D2DB37A84031354DcExchMX3Altourlo_ Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: base64 SGVsbG8gYWxsLA0KDQpJIGhhdmUgYSBxdWVzdGlvbiBhYm91dCB0aGUgaW5pdGlhbCBzZXR1cCBm b3Igb3ZpcnQuIEkgaGF2ZSAzIG5vZGVzDQp0aGF0IEkgYW0gYWJvdXQgcmVhZHkgdG8gaW5zdGFs bCBhIGh5cGVyIGNvbnZlcmdlZCBzZXR1cCB1c2luZyBHbHVzdGVyDQpmb3Igc3RvcmFnZSBhbmQg aG9zdGVkLWVuZ2luZS4NCg0KTXkgcXVlc3Rpb24gaXMgdGhpczoNCg0KV2hhdCBkb2VzIHRoZSBu ZXR3b3JraW5nIHNldHVwIG5lZWQgdG8gbG9vayBsaWtlIGF0IGluc3RhbGwgdGltZSA/IERvDQpJ IG5lZWQgdG8gc2V0dXAgYWxsIG9mIHRoZSBib25kcywgdmxhbnMgYW5kIGJyaWRnZXMgYmVmb3Jl IEkgc3RhcnQgdGhlIGluc3RhbGwNCm9yIHNob3VsZCBJIGp1c3Qgc2V0IGFuIG92aXJ0bWdtdCBi b25kL3ZsYW4vYnJpZGdlIGFuZCBzZXR1cCB0aGUgcmVzdCBvZiB0aGUNCm5ldHdvcmtpbmcgaW5z aWRlIG9mIG92aXJ0LiBJIGV4cGVjdCB0byBuZWVkIDMgb3IgNCBuZXR3b3Jrcy92bGFuIHRvIG1h dGNoDQpteSBleGlzdGluZyBuZXR3b3JrcyB0byBhdHRhY2ggdm0ncyB0by4NCg0KQW55IGhlbHAg b3IgcG9pbnRlcnMgd291bGQgYmUgYXBwcmVjaWF0ZWQuDQoNClRoYW5rIFlvdQ0K77u/DQo= --_000_C46E817F004EDF47A188C55D2DB37A84031354DcExchMX3Altourlo_ Content-Type: text/html; charset=UTF-8 Content-Transfer-Encoding: base64 PGh0bWw+DQo8aGVhZD4NCjxtZXRhIGh0dHAtZXF1aXY9IkNvbnRlbnQtVHlwZSIgY29udGVudD0i dGV4dC9odG1sOyBjaGFyc2V0PXV0Zi04Ij4NCjxtZXRhIG5hbWU9IkdlbmVyYXRvciIgY29udGVu dD0iTWljcm9zb2Z0IFdvcmQgMTUgKGZpbHRlcmVkIG1lZGl1bSkiPg0KPHN0eWxlPjwhLS0NCi8q IEZvbnQgRGVmaW5pdGlvbnMgKi8NCkBmb250LWZhY2UNCgl7Zm9udC1mYW1pbHk6SGVsdmV0aWNh Ow0KCXBhbm9zZS0xOjIgMTEgNiA0IDIgMiAyIDIgMiA0O30NCkBmb250LWZhY2UNCgl7Zm9udC1m YW1pbHk6IkNhbWJyaWEgTWF0aCI7DQoJcGFub3NlLTE6MiA0IDUgMyA1IDQgNiAzIDIgNDt9DQpA Zm9udC1mYWNlDQoJe2ZvbnQtZmFtaWx5OkNhbGlicmk7DQoJcGFub3NlLTE6MiAxNSA1IDIgMiAy IDQgMyAyIDQ7fQ0KQGZvbnQtZmFjZQ0KCXtmb250LWZhbWlseTpUYWhvbWE7DQoJcGFub3NlLTE6 MiAxMSA2IDQgMyA1IDQgNCAyIDQ7fQ0KLyogU3R5bGUgRGVmaW5pdGlvbnMgKi8NCnAuTXNvTm9y bWFsLCBsaS5Nc29Ob3JtYWwsIGRpdi5Nc29Ob3JtYWwNCgl7bWFyZ2luOjBpbjsNCgltYXJnaW4t Ym90dG9tOi4wMDAxcHQ7DQoJZm9udC1zaXplOjExLjBwdDsNCglmb250LWZhbWlseToiQ2FsaWJy aSIsc2Fucy1zZXJpZjt9DQphOmxpbmssIHNwYW4uTXNvSHlwZXJsaW5rDQoJe21zby1zdHlsZS1w cmlvcml0eTo5OTsNCgljb2xvcjojMDU2M0MxOw0KCXRleHQtZGVjb3JhdGlvbjp1bmRlcmxpbmU7 fQ0KYTp2aXNpdGVkLCBzcGFuLk1zb0h5cGVybGlua0ZvbGxvd2VkDQoJe21zby1zdHlsZS1wcmlv cml0eTo5OTsNCgljb2xvcjojOTU0RjcyOw0KCXRleHQtZGVjb3JhdGlvbjp1bmRlcmxpbmU7fQ0K c3Bhbi5FbWFpbFN0eWxlMTcNCgl7bXNvLXN0eWxlLXR5cGU6cGVyc29uYWwtY29tcG9zZTsNCglm b250LWZhbWlseToiQ2FsaWJyaSIsc2Fucy1zZXJpZjsNCgljb2xvcjp3aW5kb3d0ZXh0O30NCi5N c29DaHBEZWZhdWx0DQoJe21zby1zdHlsZS10eXBlOmV4cG9ydC1vbmx5Ow0KCWZvbnQtZmFtaWx5 OiJDYWxpYnJpIixzYW5zLXNlcmlmO30NCkBwYWdlIFdvcmRTZWN0aW9uMQ0KCXtzaXplOjguNWlu IDExLjBpbjsNCgltYXJnaW46MS4waW4gMS4waW4gMS4waW4gMS4waW47fQ0KZGl2LldvcmRTZWN0 aW9uMQ0KCXtwYWdlOldvcmRTZWN0aW9uMTt9DQotLT48L3N0eWxlPjwhLS1baWYgZ3RlIG1zbyA5 XT48eG1sPg0KPG86c2hhcGVkZWZhdWx0cyB2OmV4dD0iZWRpdCIgc3BpZG1heD0iMTAyNiIgLz4N CjwveG1sPjwhW2VuZGlmXS0tPjwhLS1baWYgZ3RlIG1zbyA5XT48eG1sPg0KPG86c2hhcGVsYXlv dXQgdjpleHQ9ImVkaXQiPg0KPG86aWRtYXAgdjpleHQ9ImVkaXQiIGRhdGE9IjEiIC8+DQo8L286 c2hhcGVsYXlvdXQ+PC94bWw+PCFbZW5kaWZdLS0+DQo8L2hlYWQ+DQo8Ym9keSBsYW5nPSJFTi1V UyIgbGluaz0iIzA1NjNDMSIgdmxpbms9IiM5NTRGNzIiPg0KPGRpdiBjbGFzcz0iV29yZFNlY3Rp b24xIj4NCjxwIGNsYXNzPSJNc29Ob3JtYWwiPjxzcGFuIHN0eWxlPSJmb250LXNpemU6MTAuNXB0 O2ZvbnQtZmFtaWx5OiZxdW90O0hlbHZldGljYSZxdW90OyxzYW5zLXNlcmlmO2JhY2tncm91bmQ6 d2hpdGUiPkhlbGxvIGFsbCw8L3NwYW4+PHNwYW4gc3R5bGU9ImZvbnQtc2l6ZToxMC41cHQ7Zm9u dC1mYW1pbHk6JnF1b3Q7SGVsdmV0aWNhJnF1b3Q7LHNhbnMtc2VyaWYiPjxicj4NCjxicj4NCjxz cGFuIHN0eWxlPSJiYWNrZ3JvdW5kOndoaXRlIj5JIGhhdmUgYSBxdWVzdGlvbiBhYm91dCB0aGUg aW5pdGlhbCBzZXR1cCBmb3Igb3ZpcnQuIEkgaGF2ZSAzIG5vZGVzPC9zcGFuPjxicj4NCjxzcGFu IHN0eWxlPSJiYWNrZ3JvdW5kOndoaXRlIj50aGF0IEkgYW0gYWJvdXQgcmVhZHkgdG8gaW5zdGFs bCBhIGh5cGVyIGNvbnZlcmdlZCBzZXR1cCB1c2luZyBHbHVzdGVyPC9zcGFuPjxicj4NCjxzcGFu IHN0eWxlPSJiYWNrZ3JvdW5kOndoaXRlIj5mb3Igc3RvcmFnZSBhbmQgaG9zdGVkLWVuZ2luZS48 L3NwYW4+PGJyPg0KPGJyPg0KPHNwYW4gc3R5bGU9ImJhY2tncm91bmQ6d2hpdGUiPk15IHF1ZXN0 aW9uIGlzIHRoaXM6PC9zcGFuPjxicj4NCjxicj4NCjxzcGFuIHN0eWxlPSJiYWNrZ3JvdW5kOndo aXRlIj5XaGF0IGRvZXMgdGhlIG5ldHdvcmtpbmcgc2V0dXAgbmVlZCB0byBsb29rIGxpa2UgYXQg aW5zdGFsbCB0aW1lID8gRG88L3NwYW4+PGJyPg0KPHNwYW4gc3R5bGU9ImJhY2tncm91bmQ6d2hp dGUiPkkgbmVlZCB0byBzZXR1cCBhbGwgb2YgdGhlIGJvbmRzLCB2bGFucyBhbmQgYnJpZGdlcyBi ZWZvcmUgSSBzdGFydCB0aGUgaW5zdGFsbDwvc3Bhbj48YnI+DQo8c3BhbiBzdHlsZT0iYmFja2dy b3VuZDp3aGl0ZSI+b3Igc2hvdWxkIEkganVzdCBzZXQgYW4gb3ZpcnRtZ210IGJvbmQvdmxhbi9i cmlkZ2UgYW5kIHNldHVwIHRoZSByZXN0IG9mIHRoZTwvc3Bhbj48YnI+DQo8c3BhbiBzdHlsZT0i YmFja2dyb3VuZDp3aGl0ZSI+bmV0d29ya2luZyBpbnNpZGUgb2Ygb3ZpcnQuIEkgZXhwZWN0IHRv IG5lZWQgMyBvciA0IG5ldHdvcmtzL3ZsYW4gdG8gbWF0Y2g8L3NwYW4+PGJyPg0KPHNwYW4gc3R5 bGU9ImJhY2tncm91bmQ6d2hpdGUiPm15IGV4aXN0aW5nIG5ldHdvcmtzIHRvIGF0dGFjaCB2bSdz IHRvLjwvc3Bhbj48YnI+DQo8YnI+DQo8c3BhbiBzdHlsZT0iYmFja2dyb3VuZDp3aGl0ZSI+QW55 IGhlbHAgb3IgcG9pbnRlcnMgd291bGQgYmUgYXBwcmVjaWF0ZWQuPC9zcGFuPjxicj4NCjxicj4N CjxzcGFuIHN0eWxlPSJiYWNrZ3JvdW5kOndoaXRlIj5UaGFuayBZb3U8L3NwYW4+PGJyPg0KPC9z cGFuPjxzcGFuIHN0eWxlPSJmb250LXNpemU6MTAuNXB0O2ZvbnQtZmFtaWx5OiZxdW90O1RhaG9t YSZxdW90OyxzYW5zLXNlcmlmO2JhY2tncm91bmQ6d2hpdGUiPu+7vzwvc3Bhbj48bzpwPjwvbzpw PjwvcD4NCjwvZGl2Pg0KPC9ib2R5Pg0KPC9odG1sPg0K --_000_C46E817F004EDF47A188C55D2DB37A84031354DcExchMX3Altourlo_--

1 0