- Users - oVirt List Archives

node IPs can't be pingued on a fresh 4.4.4 installation
by Nathanaël Blanchet 04 Mar '21

04 Mar '21

Hello On a fresh installation of a 4.4.4 node, I configured network so as to get dhcp delivered IP for gluster and migration services. After IPs have been delivered, they can't be pingued and vms migrations fail. All work as expected once I reactivate each bridge with nmcli/nmtui... This bug is present on each new node installation. -- Nathanaël Blanchet Supervision réseau SIRE 227 avenue Professeur-Jean-Louis-Viala 34193 MONTPELLIER CEDEX 5 Tél. 33 (0)4 67 54 84 55 Fax 33 (0)4 67 54 84 14 blanchet(a)abes.fr

2 1

Right Glusterfs Config on HA Server
by Marcel d'Heureuse 04 Mar '21

04 Mar '21

Hi Guys or Girls, I have a problem in a productive system. We use three Servers which have a Raid 5 with four Harddrives SATA 8 TB 7200 rpms. The Systems are interconnected for Glusterfs with 1 GB/s. The Network Load between all three servers are between 5 and 8 % of the network. The Glusterfs has a separate VLAN which complete isolated from other networks. Find attached a small drawing. On that server we rum as HA and there are 8 VMs installed. Most of the VMs working well but if there is high load on the system some of the VM can't write the Data in a "good" speed on the disks. The Glusterfs is configured as Replica on the Raid5 disk which is as Jbob in Glusterfs defined. If i take a look on the iostats i can see that the Harddisk have round 50 open connections some of the glusterfs and a lot of the vms. In side the VMs i can see long iowaiting times from 300 up to 600 ms. With is on case of a Posgresql database very long. Should we configure the Raid5 controller out that the controller only should 4 disks with 8 TB and Glusterfs should connect directly to the /dev/sd[b-e]? What do you think? Will SSD HDD will help on performance but the same config with Raid5 and Jbod could be the bigger problem. Thanks Marcel

2 1

4.5 compatibility cluster
by Nathanaël Blanchet 03 Mar '21

03 Mar '21

2 1

Newly uploaded disk stuck in 'Finalizing Failure' status
by n.bouwhuis＠speakup.nl 03 Mar '21

03 Mar '21

Hey there, A few days ago, I tried to create a new template using one of the Ansible playbooks I frequently use. This time, the upload of the disk failed, possibly due to an unrelated error. The disk is now stuck in Ovirt. It has the status 'Finalizing Failure' and it's locked, thus I cannot remove it. Trying to unlock the disk with the 'unlock_entity.sh' helper utility does not help. The utility says it has completed it task successfully but the disk remains in this state. I decided to check the logs, and see that `engine.log` gets spammed with these lines every 10 seconds ``` 2021-03-03 09:05:38,335Z WARN [org.ovirt.engine.core.bll.storage.disk.image.TransferDiskImageCommand] (EE-ManagedScheduledExecutorService-engineScheduledThreadPool-Thread-45) [redacted] Failed to stop image transfer session. Ticket does not exist for image '[disk uuid]' ``` How can I force Ovirt to remove this disk? I presume the upload failure itself is a different error, possibly related to our setup. Hence this is not the topic of this thread. I just want to know how I can remove these disks. Thanks, Nick

3 3

SHE upgrade from 4.3 to 4.4 doubts
by Gianluca Cecchi 03 Mar '21

03 Mar '21

Hello, I would like to get some clarifications about the SHE environment upgrade from 4.3.10 to 4.4.4. Example scenario two hosts, both configured as HE hosts. Interested both in iSCSI environment and in FC environment. Going through here: https://www.ovirt.org/documentation/upgrade_guide/#Upgrading_the_Manager_to… I have some doubts: 1) general one between step 5 and 6 in section 4.4, actually the current 4.3 engine VM is still running its OS (even if with ovirt-engine service stopped) and the VM is running on the host you are going to scratch. So I think before scratching the host and reinstalling it (step 6), it should be clarified some step like - shutdown engine VM - shutdown host (is it ok in clean way or do I have to simply power off it....?) - install from scratch ovirt-ng node 4.4.4 on host 2) general one why in external engine upgrade guide it is not specified to stop ovirt-engine service before executing the backup, while in SHE it is specified? See steps on section 2.3 here: https://www.ovirt.org/documentation/upgrade_guide/#Upgrading_from_4-3 expected different behaviour? Or any change needed in the doc? 3) SHE when iSCSI and FC It is clear that one new domain is to be provided, intended for the new engine 4.4 VM It is clear that during install of the new host in 4.4 it is safe to have shared LUNs masked / not accessible so that you don't risk to corrupt current 4.3 data It is not clear in my opinion what to do before running the step 8 of 4.4 section: hosted-engine --deploy --restore-from-file=backup.bck a) iSCSI in general the configured iSCSI sessions are activated only when the host is being activated. So for example when you put host into maintenance, they are logged off. In this stage of upgrade what is expected I execute before running the hosted-engine --deploy command? Will the command log in into iSCSI sessions during itsmexecution (because of the restore) or do I have to create / log in the connections before running it? b) FC what should I have on host before running the command? Only the current LUns (+ the new one intended for new hosted engine VM) visible, so that I see all of them as output of "multipath -l" command and then the hosted-engine --deploy command would mount the related filesystems and so on..? Possibly it would be nice to have an example output of the hosted-engine --deploy --restore-from-file=backup.bck command inside the doc page.... to see its expected workflow Thanks for reading, Gianluca

1 0

Upgrade from 4.3.5 to 4.3.10 HE Host issue
by Vrgotic, Marko 03 Mar '21

03 Mar '21

Hi oVirt, Yesterday I upgraded one of my oVIrt platform from 4.3.5 to 4.3.10. Platform has 10Hosts with 3Hosts as Hosts for HA. Before upgrade, all three Hosts were acknowledged Hosts for HE (little happy crown). Pre upgrade: Host1 – HE available host Host2 – HE current host Host3 – HE available host Upgraded first HE to 4.3.10, than started with HE Hosts – post upgrade of Host2, the crown disappeared and did not show up. This happens sometimes, and I usually reinstall the host, than execute HE UNDEPLOY and DEPLOY, which fixes the state. However, this time, after such actions, the server is still not an acknowledged HE host – no crown. However, if I try to remove it, oVIrt says that looks like HE is deploy on it and need to be removed, but command “hosted-engine –vm-status” says you must deploy first. I removed the Host, reinstalled the OS on it, deployed it again as new, synced all networks, than deploy once more with HE Deploy, still same issue. Any suggestions? ----- kind regards/met vriendelijke groeten Marko Vrgotic Sr. System Engineer @ System Administration ActiveVideo o: +31 (35) 6774131 m: +31 (65) 5734174 e: m.vrgotic(a)activevideo.com<mailto:m.vrgotic@activevideo.com> w: www.activevideo.com<http://www.activevideo.com> ActiveVideo Networks BV. Mediacentrum 3745 Joop van den Endeplein 1.1217 WJ Hilversum, The Netherlands. The information contained in this message may be legally privileged and confidential. It is intended to be read only by the individual or entity to whom it is addressed or by their designee. If the reader of this message is not the intended recipient, you are on notice that any distribution of this message, in any form, is strictly prohibited. If you have received this message in error, please immediately notify the sender and/or ActiveVideo Networks, LLC by telephone at +1 408.931.9200 and delete or destroy any copy of this message.

1 0

Multipath flapping with SAS via FCP
by Benoit Chatelain 02 Mar '21

02 Mar '21

Hi, I have some troubles with multipath. When I add SAS disk over FCP as Storage Domain via oVirt WebUI, The first link as active, but the second is stuck as failed. Volum disk is provided from Dell Compellent via FCP, and disk is transported in SAS. multipath is flapping in all hypervisor from the same domain disk: [root@isildur-adm ~]# tail -f /var/log/messages Feb 25 11:48:21 isildur-adm kernel: device-mapper: multipath: 253:3: Failing path 8:32. Feb 25 11:48:24 isildur-adm multipathd[659460]: 36000d31003d5c2000000000000000010: sdc - tur checker reports path is up Feb 25 11:48:24 isildur-adm multipathd[659460]: 8:32: reinstated Feb 25 11:48:24 isildur-adm multipathd[659460]: 36000d31003d5c2000000000000000010: remaining active paths: 2 Feb 25 11:48:24 isildur-adm kernel: device-mapper: multipath: 253:3: Reinstating path 8:32. Feb 25 11:48:24 isildur-adm kernel: sd 1:0:1:2: alua: port group f01c state S non-preferred supports toluSNA Feb 25 11:48:24 isildur-adm kernel: sd 1:0:1:2: alua: port group f01c state S non-preferred supports toluSNA Feb 25 11:48:24 isildur-adm kernel: device-mapper: multipath: 253:3: Failing path 8:32. Feb 25 11:48:25 isildur-adm multipathd[659460]: sdc: mark as failed Feb 25 11:48:25 isildur-adm multipathd[659460]: 36000d31003d5c2000000000000000010: remaining active paths: 1 --- [root@isildur-adm ~]# multipath -ll 36000d31003d5c2000000000000000010 dm-3 COMPELNT,Compellent Vol size=1.5T features='1 queue_if_no_path' hwhandler='1 alua' wp=rw `-+- policy='service-time 0' prio=25 status=active |- 1:0:0:2 sdb 8:16 active ready running `- 1:0:1:2 sdc 8:32 failed ready running --- VDSM generate multipath.conf like this ( I have remove commented lines for read confort ) : [root@isildur-adm ~]# cat /etc/multipath.conf # VDSM REVISION 2.0 # This file is managed by vdsm. defaults { polling_interval 5 no_path_retry 16 user_friendly_names no flush_on_last_del yes fast_io_fail_tmo 5 dev_loss_tmo 30 max_fds 4096 } blacklist { protocol "(scsi:adt|scsi:sbp)" } no_path_retry 16 } Have you some idea why this link is flapping on my two hypervisor? Thanks a lot in advance. - Benoit Chatelain

4 5

How to enable nested virtualization
by miguel.garcia＠toshibagcs.com 02 Mar '21

02 Mar '21

Hi all, We are trying to run virtual box in a vm that is running over ovirt platform. I had followed the instruction to enable nested virtualization on host as described in this document https://ostechnix.com/how-to-enable-nested-virtualization-in-kvm-in-linux/ However I was not able to enable nested virtualization to the vm since nothing is listed from virsh console. Also tryed to edit vm configuration lookig up for "cpu mode" or "copy cpu configuration as host" Also from oVirt admin portal I had enabled host for nested virtualization through Compute > Host > selected Host > edit > Kernel Nested virtualization checked. But the host still returns: $ cat /sys/module/kvm_intel/parameters/nested N

4 5

kvm host becomes non operational after breaking a bonding interface
by LS CHENG 02 Mar '21

02 Mar '21

Hi I have created a couple of bonding interfaces in the administrator portal, due to some miss configuration I had to break the bond interfaces, what I observe is that after breaking the bonding interfaces the KVM host becomes non operational and it stays in such state unless I add the bonding interfaces back. Anyone have observed this behaviour? Thanks

2 6

2 Node oVirt Cluster
by justin.lamp96＠gmail.com 01 Mar '21

01 Mar '21

Hey there, I tried using oVirt for some time now and like to convert my main Proxmox Cluster (2 Nodes + RPI for Quorum) to oVirt. But I obvioulsy need three servers to do HA. Now I am asking myself: can't I just use the PI as an arbiter node for the Selfhosted-Engine on gluster? I tried running the playbook already, but it's always failing and even if the gluster deployment would go through, it would most likely fail aftwards, right? Before I waste too much energy and time into that, does anyone of you guys use a 2 node cluster? And no I can't add another node (energy + space + money)! Also I know with doing that I'm totally on my own etcetera Thanks!

3 6