- Users - oVirt List Archives

Replace bad Host from a 9 Node hyperconverged setup 4.3.3
by adrianquintero＠gmail.com 10 Jun '19

10 Jun '19

Anybody have had to replace a failed host from a 3, 6, or 9 node hyperconverged setup with gluster storage? One of my hosts is completely dead, I need to do a fresh install using ovirt node iso, can anybody point me to the proper steps? thanks,

6 15

Re: run ovirt without firewalld
by Strahil 10 Jun '19

10 Jun '19

Then ... You have no choice , but to enable firewalld via a cron job or systemd service. I think Sahina and/or Sandro can hint you how to proceed . Best Regards, Strahil Nikolov On Jun 10, 2019 20:02, Chris Boon <cpjboon(a)gmail.com> wrote: > > yeah i noticed the same, HostedEngine doesn't want to migrate or start due to disabled firewalld. > But some organizations have a company policy not to run firewalls on servers, only edge firewalls. > So automation tools disable firewalld :( > > best regards, > Chris > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/JQOROLNXKSQHT…

1 0

Re: Replace bad Host from a 9 Node hyperconverged setup 4.3.3
by Strahil 10 Jun '19

10 Jun '19

Hi Adrian, Did you fix the issue with the gluster and the missing brick? If yes, try to set the 'old' host in maintenance and then forcefully remove it from oVirt. If it succeeds (and it should), then you can add the server back and then check what happens. Best Regards, Strahil NikolovOn Jun 10, 2019 18:12, Adrian Quintero <adrianquintero(a)gmail.com> wrote: > > Ok I have tried reinstalling the server from scratch with a different name and IP address and when trying to add it to cluster I get the following error: > > Event details > ID: 505 > Time: Jun 10, 2019, 10:00:00 AM > Message: Host myshost2.virt.iad3p installation failed. Host myhost2.mydomain.com reports unique id which already registered for myhost1.mydomain.com > > I am at a loss here, I don't have a brand new server to do this and in need to re-use what I have. > > > From the oVirt engine log (/var/log/ovirt-engine/engine.log): > 2019-06-10 10:57:59,950-04 ERROR [org.ovirt.engine.core.dal.dbbroker.auditloghandling.AuditLogDirector] (EE-ManagedThreadFactory-engine-Thread-37744) [9b88055] EVENT_ID: VDS_INSTALL_FAILED(505), Host myhost2.mydomain.com installation failed. Host myhost2.mydomain.com reports unique id which already registered for myhost1.mydomain.com > > So in the /var/log/ovirt-engine/host-deploy/ovirt-host-deploy-20190610105759-myhost2.mydomain.com-9b88055.log of the ovirt engine I see that the host deploy is running the following command to identify the system, if this is the case then it will never work :( because it identifies each host using the system uuid. > > dmidecode -s system-uuid > b64d566e-055d-44d4-83a2-d3b83f25412e > > > Any suggestions? > > Thanks > > On Sat, Jun 8, 2019 at 11:23 AM Adrian Quintero <adrianquintero(a)gmail.com> wrote: >> >> Leo, >> I did try putting it under maintenance and checking to ignore gluster and it did not work. >> Error while executing action: >> -Cannot remove host. Server having gluster volume. >> >> Note: the server was already reinstalled so gluster will never see the volumes or bricks for this server. >> >> I will rename the server to myhost2.mydomain.com and try to replace the bricks hopefully that might work, however it would be good to know that you can re-install from scratch an existing cluster server and put it back to the cluster. >> >> Still doing research hopefully we can find a way. >> >> thanks again >> >> Adrian >> >> >> >> >> On Fri, Jun 7, 2019 at 2:39 AM Leo David <leoalex(a)gmail.com> wrote: >>> >>> You will need to remove the storage role from that server first ( not being part of gluster cluster ). >>> I cannot test this right now on production, but maybe putting host although its already died under "mantainance" while checking to ignore guster warning will let you remove it. >>> Maybe I am wrong about the procedure, can anybody input an advice helping with this situation ? >>> Cheers, >>> >>> Leo >>> >>> >>> >>> >>> On Thu, Jun 6, 2019 at 9:45 PM Adrian Quintero <adrianquintero(a)gmail.com> wrote: >>>> >>>> I tried removing the bad host but running into the following issue , any idea?

2 1

Re: run ovirt without firewalld
by Strahil 10 Jun '19

10 Jun '19

I remember a case where my HostedEngine couldn't start due to disqbled firewalld. I'd recommend you to keep it running , as it will only be benefitial . Best Regards, Strahil NikolovOn Jun 8, 2019 13:38, Chris Boon <cpjboon(a)gmail.com> wrote: > > Hello, > > When i deploy and use oVirt 4.3, is firewalld really needed on hypervisors or can oVirt 4.3 run and function with a disabled firewalld? > > Regards, > Chris > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/7G4KQQCEVIXCK…

2 1

Erro seabios ovirt
by LIONS TECNOLOGIA 10 Jun '19

10 Jun '19

Please! I am a beginner in ovirt and I installed a single server, I am with the following problem, when I open the virtual machine console screen, it shows this black screen attached, I would like to know how to solve this problem.

2 1

Re: Failed to activate Storage Domain --- ovirt 4.2
by Eyal Shenitzky 10 Jun '19

10 Jun '19

Nir, can you please have a look? On Mon, Jun 10, 2019 at 2:29 PM Aminur Rahman <aminur.rahman(a)iongroup.com> wrote: > Hi Eyal > > > > We’re using: > > > > ovirt-engine-4.2.8.2-1.el7.noarch > > vdsm-client-4.20.46-1.el7.noarch > > > > Thanks > > *Aminur Rahman* > > aminur.rahman(a)iongroup.com > > *t* > > +44 20 7398 0243 <+44%2020%207398%200243> > > *m* > > +44 7825 780697 <+44%207825%20780697%3c> > > iongroup.com <https://www.iongroup.com> > > > > *From:* Eyal Shenitzky <eshenitz(a)redhat.com> > *Sent:* 10 June 2019 07:20 > *To:* Aminur Rahman <aminur.rahman(a)iongroup.com>; Nir Soffer < > nsoffer(a)redhat.com> > *Cc:* users <users(a)ovirt.org> > *Subject:* Re: [ovirt-users] Failed to activate Storage Domain --- ovirt > 4.2 > > > > Hi Aminur, > > > > Can you please send the engine and vdsm versions? > > > > > > On Fri, Jun 7, 2019 at 5:03 PM <aminur.rahman(a)iongroup.com> wrote: > > Hi > Has anyone experiencing the following issue with Storage Domain - > > Failed to activate Storage Domain cLUN-R940-DC2-dstore01 -- > VDSM command ActivateStorageDomainVDS failed: Storage domain does not > exist: (u'1b0ef853-fd71-45ea-8165-cc6047a267bc',) > > Currently, the storge Domain is Inactive and strangely, the VMs are > running as normal. We can't manage or extend the volume size of this > storage domain. The pvscan shows as: > [root@uk1-ion-ovm-18 pvscan > /dev/mapper/36000d310056978000000000000000014: Checksum error at offset > 4397954425856 > Couldn't read volume group metadata from > /dev/mapper/36000d310056978000000000000000014. > Metadata location on /dev/mapper/36000d310056978000000000000000014 at > 4397954425856 has invalid summary for VG. > Failed to read metadata summary from > /dev/mapper/36000d310056978000000000000000014 > Failed to scan VG from /dev/mapper/36000d310056978000000000000000014 > > I have tired the following steps: > 1. Restarted ovirt-engine.service > 2. tried to restore the metadata using vgcfgrestore but it failed with the > following error: > > [root@uk1-ion-ovm-19 backup]# vgcfgrestore > 36000d310056978000000000000000014 > Volume group 36000d310056978000000000000000014 has active volume: . > WARNING: Found 1 active volume(s) in volume group > "36000d310056978000000000000000014". > Restoring VG with active LVs, may cause mismatch with its metadata. > Do you really want to proceed with restore of volume group > "36000d310056978000000000000000014", while 1 volume(s) are active? [y/n]: y > /dev/mapper/36000d310056978000000000000000014: Checksum error at offset > 4397954425856 > Couldn't read volume group metadata from > /dev/mapper/36000d310056978000000000000000014. > Metadata location on /dev/mapper/36000d310056978000000000000000014 at > 4397954425856 has invalid summary for VG. > Failed to read metadata summary from > /dev/mapper/36000d310056978000000000000000014 > Failed to scan VG from /dev/mapper/36000d310056978000000000000000014 > /etc/lvm/backup/36000d310056978000000000000000014: stat failed: No such > file or directory > Couldn't read volume group metadata from file. > Failed to read VG 36000d310056978000000000000000014 from > /etc/lvm/backup/36000d310056978000000000000000014 > Restore failed. > > Please let me know if anyone knows any possible resolution. > > -AMinur > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > <https://nam05.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.ovirt…> > oVirt Code of Conduct: > https://www.ovirt.org/community/about/community-guidelines/ > <https://nam05.safelinks.protection.outlook.com/?url=https%3A%2F%2Fwww.ovirt…> > List Archives: > https://lists.ovirt.org/archives/list/users@ovirt.org/message/W2JP7ZO5XMV66… > <https://nam05.safelinks.protection.outlook.com/?url=https%3A%2F%2Flists.ovi…> > > > > > -- > > Regards, > > Eyal Shenitzky > -- Regards, Eyal Shenitzky

1 0

oVirt survey - May 2019
by Sandro Bonazzola 10 Jun '19

10 Jun '19

As we continue to develop oVirt 4.3 and future releases, the Development and Integration teams at Red Hat would value insights on how you are deploying the oVirt environment. Please help us to hit the mark by completing this short survey. Survey will close on June 7th. If you're managing multiple oVirt deployments with very different use cases or very different deployments you can consider answering this survey multiple times. Please note the answers to this survey will be publicly accessible. This survey is under oVirt Privacy Policy available at https://www.ovirt.org/site/privacy-policy.html The survey is available here: https://forms.gle/8uzuVNmDWtoKruhm8 -- Sandro Bonazzola MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV Red Hat EMEA <https://www.redhat.com/> sbonazzo(a)redhat.com <https://red.ht/sig> <https://redhat.com/summit>

1 1

Re: [ovirt-devel] cannot add host (oVirt 4.3.3.7)
by Nir Soffer 10 Jun '19

10 Jun '19

On Sun, Jun 9, 2019 at 9:15 PM Hetz Ben Hamo <hetz(a)hetz.biz> wrote: Moving to users list, devel list is for discussion about oVirt development, not troubleshooting. I'm trying to add a new host to oVirt. The main host is Xeon E5 while the > new host is AMD Ryzen 5. > > The main host is running oVirt 4.3.3 and the new node is a minimal install > of CentOS 7.6 (1810) with all the latest updates. > Which engine version? on which OS? I'm enclosing the log files. it complains that it cannot get the oVirt > packages, perhaps wrong channel(?). Looking at the log, it's trying to use > minidnf. I don't think CentOS 7 supports DNF.. > Did you install ovirt-release43 rpm before adding the host? https://ovirt.org/download/ Nir

3 4

Re: Clusters run virtual machines or Red Hat Gluster Storage Servers
by Strahil 10 Jun '19

10 Jun '19

OVirt + Gluster is called 'Hyperconverged' setup and it supports only replica3 or a 'replica3 arbiter1' volumes. Vmware VSAN is another popular Hyperconverged Setup but requires a lot of licenses. The CPU and Disk resources are plenty on virtualization Hosts and this setup allows you to save space by removal of the iSCSI/NFS/SAN dedicated system. The setup is quite popular and it works quite well, but requires a 10G network (as load balancing smaller NICs is very hard ) - if performance is required, while even a 1 gbit/s NIC is possible to be used. Note: 1gbit/s will provide no more than 87 MB/s on gluster level for all your VMs , which is very poor. If you have 4 hosts -> one of them will not be in the gluster setup, or you will have 2 separate gluster volumes like this: oVirt1- Replica for volume A oVirt2- Replica for volume A , arbiter for volume B oVirt3 - Replica for volume B,arbiter for volume A oVirt4 - Replica for volume B Then you add them as hosts in your oVirt setup. Best Regards, Strahil NikolovOn Jun 10, 2019 05:29, xilazz(a)126.com wrote: > > Hi, everybody. When I was looking at the administrator's manual, it prompted Clusters run virtual machines or Red Hat Gluster Storage Servers. These two purposes are mad exclusive: > Virtualization and storage hosts together. When I configured the cluster, I said that the glusterfs and virt I saw were alternatives to the two checkboxes. > I would like to ask what happens when glusterfs and virt are in the same cluster? > How can I use hosted engine when I have four nodes? > Thank you very much for your reply. > _______________________________________________ > Users mailing list -- users(a)ovirt.org > To unsubscribe send an email to users-leave(a)ovirt.org > Privacy Statement: https://www.ovirt.org/site/privacy-policy/ > oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ > List Archives: https://lists.ovirt.org/archives/list/users@ovirt.org/message/CZR73TNWNRE5L…

2 1

Clusters run virtual machines or Red Hat Gluster Storage Servers
by xilazz＠126.com 10 Jun '19

10 Jun '19

Hi, everybody. When I was looking at the administrator's manual, it prompted Clusters run virtual machines or Red Hat Gluster Storage Servers. These two purposes are mad exclusive: Virtualization and storage hosts together. When I configured the cluster, I said that the glusterfs and virt I saw were alternatives to the two checkboxes. I would like to ask what happens when glusterfs and virt are in the same cluster? How can I use hosted engine when I have four nodes? Thank you very much for your reply.

1 0