January 2021 - Announce - oVirt List Archives

[ANN] oVirt 4.4.5 Third Release Candidate is now available for testing
by Sandro Bonazzola 29 Jan '21

29 Jan '21

oVirt 4.4.5 Third Release Candidate is now available for testing The oVirt Project is pleased to announce the availability of oVirt 4.4.5 Third Release Candidate for testing, as of January 29th, 2021. This update is the fifth in a series of stabilization updates to the 4.4 series. How to prevent hosts entering emergency mode after upgrade from oVirt 4.4.1 Note: Upgrading from 4.4.2 GA or later should not require re-doing these steps, if already performed while upgrading from 4.4.1 to 4.4.2 GA. These are only required to be done once. Due to Bug 1837864 <https://bugzilla.redhat.com/show_bug.cgi?id=1837864> - Host enter emergency mode after upgrading to latest build If you have your root file system on a multipath device on your hosts you should be aware that after upgrading from 4.4.1 to 4.4.5 you may get your host entering emergency mode. In order to prevent this be sure to upgrade oVirt Engine first, then on your hosts: 1. Remove the current lvm filter while still on 4.4.1, or in emergency mode (if rebooted). 2. Reboot. 3. Upgrade to 4.4.5 (redeploy in case of already being on 4.4.5). 4. Run vdsm-tool config-lvm-filter to confirm there is a new filter in place. 5. Only if not using oVirt Node: - run "dracut --force --add multipath” to rebuild initramfs with the correct filter configuration 6. Reboot. Documentation - If you want to try oVirt as quickly as possible, follow the instructions on the Download <https://ovirt.org/download/> page. - For complete installation, administration, and usage instructions, see the oVirt Documentation <https://ovirt.org/documentation/>. - For upgrading from a previous version, see the oVirt Upgrade Guide <https://ovirt.org/documentation/upgrade_guide/>. - For a general overview of oVirt, see About oVirt <https://ovirt.org/community/about.html>. Important notes before you try it Please note this is a pre-release build. The oVirt Project makes no guarantees as to its suitability or usefulness. This pre-release must not be used in production. Installation instructions For installation instructions and additional information please refer to: https://ovirt.org/documentation/ This release is available now on x86_64 architecture for: * Red Hat Enterprise Linux 8.3 or newer * CentOS Linux (or similar) 8.3 or newer This release supports Hypervisor Hosts on x86_64 and ppc64le architectures for: * Red Hat Enterprise Linux 8.3 or newer * CentOS Linux (or similar) 8.3 or newer * oVirt Node 4.4 based on CentOS Linux 8.3 (available for x86_64 only) See the release notes [1] for installation instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is already available for CentOS Linux 8 - oVirt Node NG is already available for CentOS Linux 8 - We found a few issues while testing on CentOS Stream so we are still basing oVirt 4.4.5 Node and Appliance on CentOS Linux. Additional Resources: * Read more about the oVirt 4.4.5 release highlights: http://www.ovirt.org/release/4.4.5/ * Get more oVirt project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] http://www.ovirt.org/release/4.4.5/ [2] http://resources.ovirt.org/pub/ovirt-4.4-pre/iso/ -- Sandro Bonazzola MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV Red Hat EMEA <https://www.redhat.com/> sbonazzo(a)redhat.com <https://www.redhat.com/> *Red Hat respects your work life balance. Therefore there is no need to answer this email out of your office hours.*

1 0

[ANN] oVirt 4.4.5 Second Release Candidate is now available for testing
by Sandro Bonazzola 22 Jan '21

22 Jan '21

oVirt 4.4.5 Second Release Candidate is now available for testing The oVirt Project is pleased to announce the availability of oVirt 4.4.5 Second Release Candidate for testing, as of January 21st, 2021. This update is the fifth in a series of stabilization updates to the 4.4 series. How to prevent hosts entering emergency mode after upgrade from oVirt 4.4.1 Note: Upgrading from 4.4.2 GA or later should not require re-doing these steps, if already performed while upgrading from 4.4.1 to 4.4.2 GA. These are only required to be done once. Due to Bug 1837864 <https://bugzilla.redhat.com/show_bug.cgi?id=1837864> - Host enter emergency mode after upgrading to latest build If you have your root file system on a multipath device on your hosts you should be aware that after upgrading from 4.4.1 to 4.4.5 you may get your host entering emergency mode. In order to prevent this be sure to upgrade oVirt Engine first, then on your hosts: 1. Remove the current lvm filter while still on 4.4.1, or in emergency mode (if rebooted). 2. Reboot. 3. Upgrade to 4.4.5 (redeploy in case of already being on 4.4.5). 4. Run vdsm-tool config-lvm-filter to confirm there is a new filter in place. 5. Only if not using oVirt Node: - run "dracut --force --add multipath” to rebuild initramfs with the correct filter configuration 6. Reboot. Documentation - If you want to try oVirt as quickly as possible, follow the instructions on the Download <https://ovirt.org/download/> page. - For complete installation, administration, and usage instructions, see the oVirt Documentation <https://ovirt.org/documentation/>. - For upgrading from a previous version, see the oVirt Upgrade Guide <https://ovirt.org/documentation/upgrade_guide/>. - For a general overview of oVirt, see About oVirt <https://ovirt.org/community/about.html>. Important notes before you try it Please note this is a pre-release build. The oVirt Project makes no guarantees as to its suitability or usefulness. This pre-release must not be used in production. Installation instructions For installation instructions and additional information please refer to: https://ovirt.org/documentation/ This release is available now on x86_64 architecture for: * Red Hat Enterprise Linux 8.3 or newer * CentOS Linux (or similar) 8.3 or newer This release supports Hypervisor Hosts on x86_64 and ppc64le architectures for: * Red Hat Enterprise Linux 8.3 or newer * CentOS Linux (or similar) 8.3 or newer * oVirt Node 4.4 based on CentOS Linux 8.3 (available for x86_64 only) See the release notes [1] for installation instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is already available for CentOS Linux 8 - oVirt Node NG is already available for CentOS Linux 8 - We found a few issues while testing on CentOS Stream so we are still basing oVirt 4.4.5 Node and Appliance on CentOS Linux. Additional Resources: * Read more about the oVirt 4.4.5 release highlights: http://www.ovirt.org/release/4.4.5/ * Get more oVirt project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] http://www.ovirt.org/release/4.4.5/ [2] http://resources.ovirt.org/pub/ovirt-4.4-pre/iso/ -- Sandro Bonazzola MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV Red Hat EMEA <https://www.redhat.com/> sbonazzo(a)redhat.com <https://www.redhat.com/> *Red Hat respects your work life balance. Therefore there is no need to answer this email out of your office hours.*

1 0

[ANN] oVirt 4.4.5 First Release Candidate is now available for testing
by Lev Veyde 14 Jan '21

14 Jan '21

oVirt 4.4.5 First Release Candidate is now available for testing The oVirt Project is pleased to announce the availability of oVirt 4.4.5 First Release Candidate for testing, as of January 14th, 2021. This update is the fifth in a series of stabilization updates to the 4.4 series. How to prevent hosts entering emergency mode after upgrade from oVirt 4.4.1 Note: Upgrading from 4.4.2 GA or later should not require re-doing these steps, if already performed while upgrading from 4.4.1 to 4.4.2 GA. These are only required to be done once. Due to Bug 1837864 <https://bugzilla.redhat.com/show_bug.cgi?id=1837864> - Host enter emergency mode after upgrading to latest build If you have your root file system on a multipath device on your hosts you should be aware that after upgrading from 4.4.1 to 4.4.5 you may get your host entering emergency mode. In order to prevent this be sure to upgrade oVirt Engine first, then on your hosts: 1. Remove the current lvm filter while still on 4.4.1, or in emergency mode (if rebooted). 2. Reboot. 3. Upgrade to 4.4.5 (redeploy in case of already being on 4.4.5). 4. Run vdsm-tool config-lvm-filter to confirm there is a new filter in place. 5. Only if not using oVirt Node: - run "dracut --force --add multipath” to rebuild initramfs with the correct filter configuration 6. Reboot. Documentation - If you want to try oVirt as quickly as possible, follow the instructions on the Download <https://ovirt.org/download/> page. - For complete installation, administration, and usage instructions, see the oVirt Documentation <https://ovirt.org/documentation/>. - For upgrading from a previous version, see the oVirt Upgrade Guide <https://ovirt.org/documentation/upgrade_guide/>. - For a general overview of oVirt, see About oVirt <https://ovirt.org/community/about.html>. Important notes before you try it Please note this is a pre-release build. The oVirt Project makes no guarantees as to its suitability or usefulness. This pre-release must not be used in production. Installation instructions For installation instructions and additional information please refer to: https://ovirt.org/documentation/ This release is available now on x86_64 architecture for: * Red Hat Enterprise Linux 8.3 or newer * CentOS Linux (or similar) 8.3 or newer This release supports Hypervisor Hosts on x86_64 and ppc64le architectures for: * Red Hat Enterprise Linux 8.3 or newer * CentOS Linux (or similar) 8.3 or newer * oVirt Node 4.4 based on CentOS Linux 8.3 (available for x86_64 only) See the release notes [1] for installation instructions and a list of new features and bugs fixed. Notes: - oVirt Appliance is already available for CentOS Linux 8 - oVirt Node NG is already available for CentOS Linux 8 Additional Resources: * Read more about the oVirt 4.4.5 release highlights: http://www.ovirt.org/release/4.4.5/ * Get more oVirt project updates on Twitter: https://twitter.com/ovirt * Check out the latest project news on the oVirt blog: http://www.ovirt.org/blog/ [1] http://www.ovirt.org/release/4.4.5/ [2] http://resources.ovirt.org/pub/ovirt-4.4-pre/iso/ -- Lev Veyde Senior Software Engineer, RHCE | RHCVA | MCITP Red Hat Israel <https://www.redhat.com> lev(a)redhat.com | lveyde(a)redhat.com <https://red.ht/sig> TRIED. TESTED. TRUSTED. <https://redhat.com/trusted>

1 0

[ANN] Async release for ovirt-engine is now available
by Sandro Bonazzola 08 Jan '21

08 Jan '21

The oVirt Team has just released a new version of ovirt-engine package (4.4.4.7) that fixes a few important bugs: - [BZ 1894454](https://bugzilla.redhat.com/1894454) - VM fails to boot when moved to a cluster with a different chipset - [BZ 1908643](https://bugzilla.redhat.com/1908643) - ovirt-backend contains jar that should not be there - [BZ 1576923](https://bugzilla.redhat.com/1576923) - RFE: Ability to move master role to another domain without putting the domain to maintenance - [BZ 1911597](https://bugzilla.redhat.com/1911597) - Block manually switch master domain for Gluster domains fixes also security issue: CVE-2020-35497 ( https://cve.mitre.org/cgi-bin/cvename.cgi?name=CVE-2020-35497) - Moderate - ovirt-engine: non-admin user is able to access other users public SSH key -- Sandro Bonazzola MANAGER, SOFTWARE ENGINEERING, EMEA R&D RHV Red Hat EMEA <https://www.redhat.com/> sbonazzo(a)redhat.com <https://www.redhat.com/> *Red Hat respects your work life balance. Therefore there is no need to answer this email out of your office hours.*

1 0