August 2017 - Users - oVirt List Archives

Passing VLAN trunk to VM
by Simon Vincent 26 Mar '18

26 Mar '18

Is it possible to pass multiple VLANs to a VM (pfSense) using a single virtual NIC? All my existing oVirt networks are setup as a single tagged VLAN. I know this didn't used to be supported but wondered if this has changed. My other option is to pass each VLAN as a separate NIC to the VM however if I needed to add a new VLAN I would have to add a new interface and reboot the VM as hot-add of NICs is not supported by pfSense.

6 14

HostedEngine with HA
by Carlos Rodrigues 22 Mar '18

22 Mar '18

Hello, I have one cluster with two hosts with power management correctly configured and one virtual machine with HostedEngine over shared storage with FiberChannel. When i shutdown the network of host with HostedEngine VM, it should be possible the HostedEngine VM migrate automatically to another host? What is the expected behaviour on this HA scenario? Regards, -- Carlos Rodrigues Engenheiro de Software Sénior Eurotux Informática, S.A. | www.eurotux.com (t) +351 253 680 300 (m) +351 911 926 110

4 30

oVIRT 4.1 / iSCSI Multipathing
by Devin Acosta 05 Mar '18

05 Mar '18

I am using the latest release of oVIRT 4.1.3, and I am connecting a Dell Compelent SAN that has 2 fault domains each on a separate VLAN that I have attached to oVIRT. From what I understand I am suppose to go into “iSCSI Multipathing” option and add a BOND of the iSCSI interfaces. I have done this selecting the 2 logical networks together for iSCSI. I notice that there is an option below to select Storage Targets but if I select the storage targets below with the logical networks the the cluster goes crazy and appears to be mad. Storage, Nodes, and everything goes offline even thought I have NFS also attached to the cluster. How should this best be configured. What we notice that happens is when the server reboots it seems to log into the SAN correctly but according the the Dell SAN it is only logged into once controller. So only pulls both fault domains from a single controller. Please Advise. Devin

7 10

when creating VMs, I don't want hosted_storage to be an option
by Mike Farnam 09 Feb '18

09 Feb '18

Hi All - Is that a way to mark hosted_storage somehow so that it’s not available to add new VMs to? Right now it’s the default storage domain when adding a VM. At the least, I’d like to make another storage domain the default. Is there a way to do this? Thanks

6 8

Official Hyperconverged Gluster oVirt upgrade procedure?
by Hanson 23 Jan '18

23 Jan '18

Hi Guys, Just wondering if we have an updated manual or whats the current procedure for upgrading the nodes in a hyperconverged ovirt gluster pool? Ie Nodes run 4.0 oVirt, as well as GlusterFS, and hosted-engine running in a gluster storage domain. Put node in maintenance mode and disable glusterfs from ovirt gui, run yum update? Thanks!

4 4

[vdsm] status update: running containers alongside VMs
by Francesco Romani 05 Jan '18

05 Jan '18

Hi everyone, I'm happy to share some progress about the former "convirt"[1] project, which aims to let Vdsm containers alongside VMs, on bare metal. In the last couple of months I kept updating the patch series, which is approaching the readiness to be merged in Vdsm. Please read through this mail to see what the patchset can do now, how you could try it *now*, even before it is merged. Everyone is invited to share thoughts and ideas about how this effort could evolve. This will be a long mail; I will amend, enhance and polish the content and make a blog post (on https://mojaves.github.io) to make it easier to consume and to have some easy-to-find documentation. Later on the same content will appear also on the oVirt blog. Happy hacking! +++ # How to try how the experimental container support for Vdsm. Vdsm is gaining *experimental* support to run containers alongside VMs. Vdsm had since long time the ability to manage VMs which run containers, and recently gained support for [atomic guests](http://www.projectatomic.io/blog/2015/01/running-ovirt-guest-agent-as-privileged-container/). With the new support we are describing, you will be able to manage containers with the same, proven infrastructure that let you manage VMs. This feature is currently being developed and it is still not merged in the Vdsm codebase, so some extra work is needed if you want to try it out. We aiming to merge it in the oVirt 4.1.z cycle. ## What works, aka what to expect The basic features are expected to work: 1. Run any docker image on the public docker registry 2. Make the container accessible from the outside (aka not just from localhost) 3. Use file-based storage for persistent volumes ## What does not yet work, aka what NOT to expect Few things are planned and currently under active development: 1. Monitoring. Engine will not get any update from the container besides "VM" status (Up, Down...) One important drawback is that you will not be told the IP of the container from Engine, you will need to connect to the Vdsm host to discover it using standard docker tools. 2. Proper network integration. Some steps still need manual intervention 3. Stability and recovery - it's pre-alpha software after all! :) ## 1. Introduction and prerequisites Trying out container support affects only the host and the Vdsm. Besides add few custom properties (totally safe and supported since early 3.z), there are zero changes required to the DB and to Engine. Nevertheless, we recommend to dedicate one oVirt 4.y environment, or at least one 4.y host, to try out the container feature. To get started, first thing you need is to setup a vanilla oVirt 4.y installation. We will need to make changes to the Vdsm and to the Vdsm host, so hosted engine and/or oVirt node may add extra complexity, better to avoid them at the moment. The reminder of this tutorial assumes you are using two hosts, one for Vdsm (will be changed) and one for Engine (will require zero changes); furthermore, we assume the Vdsm host is running on CentOS 7.y. We require: - one test host for Vdsm. This host need to have one NIC dedicated to containers. We will use the [docker macvlan driver](https://raesene.github.io/blog/2016/07/23/Docker-MacVLAN/), so this NIC *must not be* part of one bridge. - docker >= 1.12 - oVirt >= 4.0.5 (Vdsm >= 4.18.15) - CentOS >= 7.2 Docker >= 1.12 is avaialable for download [here](https://docs.docker.com/engine/installation/linux/centos/) Caveats: 1. docker from official rpms conflicts con docker from CentOS, and has a different package name: docker-engine vs docker. Please note that the kubernetes package from CentOS, for example, require 'docker', not 'docker-engine'. 2. you may want to replace the default service file [with this one](https://github.com/mojaves/convirt/blob/master/patches/centos72/system… and to use this [sysconfig file](https://github.com/mojaves/convirt/blob/master/patches/centos72/syste…. Here I'm just adding the storage options docker requires, much like the CentOS docker is configured. Configuring docker like this can save you some troubleshooting, especially if you had docker from CentOS installed on the testing box. ## 2. Patch Vdsm to support containers You need to patch and rebuild Vdsm. Fetch [this patch](https://github.com/mojaves/convirt/blob/master/patches/vdsm/4.18.15.… and apply it against Vdsm 4.18.15.1. Vdsm 4.18.15.{1,2,...} are supported as well. Rebuild Vdsm and reinstall on your box. [centos 7.2 packages are here](https://github.com/mojaves/convirt/tree/master/rpms/centos72) Make sure you install the Vdsm command line client (vdsm-cli) Restart *both* Vdsm and Supervdsm, make sure Engine still works flawlessly with patched Vdsm. This ensure that no regression is introduced, and that your environment can run VMs just as before. Now we can proceed adding the container support. start docker: # systemctl start docker-engine (optional) # systemctl enable docker-engine Restart Vdsm again # systemctl restart vdsm Now we can check if Vdsm detects docker, so you can use it: still on the same Vdsm host, run $ vdsClient -s 0 getVdsCaps | grep containers containers = ['docker', 'fake'] This means this Vdsm can run containers using 'docker' and 'fake' runtimes. Ignore the 'fake' runtime; as the name suggests, is a test driver, kinda like /dev/null. Now we need to make sure the host network configuration is fine. ### 2.1. Configure the docker network for Vdsm PLEASE NOTE that the suggested network configuration assumes that * you have one network, `ovirtmgmt` (the default one) you use for everything * you have one Vdsm host with at least two NICs, one bound to the `ovirtmgmt` network, and one spare _This step is not yet automated by Vdsm_, so manual action is needed; Vdsm will take care of this automatically in the future. You can use [this helper script](https://github.com/mojaves/convirt/blob/master/patches/vdsm/cont-se…, which reuses the Vdsm libraries. Make sure you have patched Vdsm to support container before to use it. Let's review what the script needs: # ./cont-setup-net -h usage: cont-setup-net [-h] [--name [NAME]] [--bridge [BRIDGE]] [--interface [INTERFACE]] [--gateway [GATEWAY]] [--subnet [SUBNET]] [--mask [MASK]] optional arguments: -h, --help show this help message and exit --name [NAME] network name to use --bridge [BRIDGE] bridge to use --interface [INTERFACE] interface to use --gateway [GATEWAY] address of the gateway --subnet [SUBNET] subnet to use --mask [MASK] netmask to use So we need to feed --name, --interface, --gateway, --subnet and optionally --mask (default, /24, is often fine). For my case the default mask was indeed fine, so I used the script like this: # ./cont-setup-net --name ovirtmgmt --interface enp3s0 --gateway 192.168.1.1 --subnet 192.168.1.0 Thhis is the output I got: DEBUG:virt.containers.runtime:configuring runtime 'docker' DEBUG:virt.containers.command:* calling ['/bin/docker', 'network', 'inspect', 'ovirtmgmt'] Error: No such network: ovirtmgmt DEBUG:virt.containers.command:* called ['/bin/docker', 'network', 'inspect', 'ovirtmgmt'] DEBUG:virt.containers.runtime.Docker:config: cannot load 'ovirtmgmt', ignored DEBUG:virt.containers.command:* calling ['/bin/docker', 'network', 'create', '-d', 'macvlan', '--subnet=192.168.1.0/24', '--gateway=192.168.1.1', '--ip-range=192.168.1.0/24', '-o', 'parent=enp3s0', 'ovirtmgmt'] DEBUG:virt.containers.command:* called ['/bin/docker', 'network', 'create', '-d', 'macvlan', '--subnet=192.168.1.0/24', '--gateway=192.168.1.1', '--ip-range=192.168.1.0/24', '-o', 'parent=enp3s0', 'ovirtmgmt'] DEBUG:virt.containers.runtime:configuring runtime 'fake' You can clearly see what the script did, and why it needed the root privileges. Let's deoublecheck using the docker tools: # docker network ls NETWORK ID NAME DRIVER SCOPE 91535f3425a8 bridge bridge local d42f7e5561b5 host host local 621ab6dd49b1 none null local f4b88e4a67eb ovirtmgmt macvlan local # docker network inspect ovirtmgmt [ { "Name": "ovirtmgmt", "Id": "f4b88e4a67ebb7886ec74073333d613b1893272530cae4d407c95ab587c5fea1", "Scope": "local", "Driver": "macvlan", "EnableIPv6": false, "IPAM": { "Driver": "default", "Options": {}, "Config": [ { "Subnet": "192.168.1.0/24", "IPRange": "192.168.1.0/24", "Gateway": "192.168.1.1" } ] }, "Internal": false, "Containers": {}, "Options": { "parent": "enp3s0" }, "Labels": {} } ] Looks good! the host configuration is completed. Let's move to the Engine side. ## 3. Configure Engine As mentioned above, we need now to configure Engine. This boils down to: Add a few custom properties for VMs: In case you were already using custom properties, you need to amend the command line to not overwrite your existing ones. # engine-config -s UserDefinedVMProperties='volumeMap=^[a-zA-Z_-]+:[a-zA-Z_-]+$;containerImage=^[a-zA-Z]+(://|)[a-zA-Z]+$;containerType=^(docker|rkt)$' --cver=4.0 It is worth stressing that while the variables are container-specific, the VM custom properties are totally inuntrusive and old concept in oVirt, so this step is totally safe. Now restart Engine to let it use the new variables: # systemctl restart ovirt-engine The next step is actually configure one "container VM" and run it. ## 4. Create the container "VM" To finally run a container, you start creating a VM much like you always did, with few changes 1. most of the hardware-related configuration isn't relevant for container "VMs", besides cpu share and memory limits; this will be better documented in the future; unneeded configuration will just be ignored 2. You need to set some custom properties for your container "VM". Those are actually needed to enable the container flow, and they are documented in the next section. You *need* to set at least `containerType` and `containerImage`. ### 4.2. Custom variables for container support The container support needs some custom properties to be properly configured: 1. `containerImage` (*needed* to enable the container system). Just select the target image you want to run. You can use the standard syntax of the container runtimes. 2. `containerType` (*needed* to enable the container system). Selects the container runtime you want to use. All the available options are always showed. Please note that unavailable container options are not yet grayed out. If you *do not* have rkt support on your host, you still can select it, but it won't work. 3. `volumeMap` key:value like. You can map one "VM" disk (key) to one container volume (value), to have persistent storage. Only file-based storage is supported. Example configuration: `containerImage = redis` `containerType = docker` `volumeMap = vda:data` (this may not be needed, and the volume label is just for illustrative purposes) ### 4.2. A little bit of extra work: preload the images on the Vdsm host This step is not needed by the flow, and will be handled by oVirt in the future. The issue is how the container image are handled. They are stored by the container management system (rkt, docker) on each host, and they are not pre-downloaded. To shorten the duration of the first boot, you are advised to pre-download the image(s) you want to run. For example ## on the Vdsm host you want to use with containers # docker pull redis ## 5. Run the container "VM" You are now all set to run your "VM" using oVirt Engine, just like any existing VM. Some actions doesn't make sense for a container "VM", like live migration. Engine won't stop you to try to do those actions, but they will fail gracefully using the standard errors. ## 6. Next steps What to expect from this project in the future? For the integration with Vdsm, we want to fix the existing known issues, most notably: * add proper monitoring/reporting of the container health * ensure proper integration of the container image store with oVirt storage management * streamline the network configuration What is explicitely excluded yet is any Engine change. This is a Vdsm-only change at the moment, so fixing the following is currently unplanned: * First and foremost, Engine will not distinguish between real VMs and container VMs. Actions unavailable to container will not be hidden from UI. Same for monitoring and configuration data, which will be ignored. * Engine is NOT aware of the volumes one container can use. You must inspect and do the mapping manually. * Engine is NOT aware of the available container runtimes. You must select it carefully Proper integration with Engine may be added in the future once this feature exits from the experimental/provisional stage. Thanks for reading, make sure to share your thoughts on the oVirt mailing lists! +++ [1] we keep calling it that way _only_ internally, because it's a short name we are used to. After the merge/once we release it, we will use a different name, like "vdsm-containers" or something like it. -- Francesco Romani Red Hat Engineering Virtualization R & D Phone: 8261328 IRC: fromani

3 2

Empty cgroup files on centos 7.3 host
by Florian Schmid 18 Dec '17

18 Dec '17

Hi, I wanted to monitor disk IO and R/W on all of our oVirt centos 7.3 hypervisor hosts, but it looks like that all those files are empty. For example: ls -al /sys/fs/cgroup/blkio/machine.slice/machine-qemu\\x2d14\\x2dHostedEngine.scope/ insgesamt 0 drwxr-xr-x. 2 root root 0 30. Mai 10:09 . drwxr-xr-x. 16 root root 0 26. Jun 09:25 .. -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_merged -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_merged_recursive -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_queued -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_queued_recursive -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_service_bytes -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_service_bytes_recursive -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_serviced -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_serviced_recursive -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_service_time -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_service_time_recursive -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_wait_time -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.io_wait_time_recursive -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.leaf_weight -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.leaf_weight_device --w-------. 1 root root 0 30. Mai 10:09 blkio.reset_stats -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.sectors -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.sectors_recursive -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.throttle.io_service_bytes -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.throttle.io_serviced -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.throttle.read_bps_device -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.throttle.read_iops_device -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.throttle.write_bps_device -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.throttle.write_iops_device -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.time -r--r--r--. 1 root root 0 30. Mai 10:09 blkio.time_recursive -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.weight -rw-r--r--. 1 root root 0 30. Mai 10:09 blkio.weight_device -rw-r--r--. 1 root root 0 30. Mai 10:09 cgroup.clone_children --w--w--w-. 1 root root 0 30. Mai 10:09 cgroup.event_control -rw-r--r--. 1 root root 0 30. Mai 10:09 cgroup.procs -rw-r--r--. 1 root root 0 30. Mai 10:09 notify_on_release -rw-r--r--. 1 root root 0 30. Mai 10:09 tasks I thought, I can get my needed values from there, but all files are empty. Looking at this post: http://lists.ovirt.org/pipermail/users/2017-January/079011.html this should work. Is this normal on centos 7.3 with oVirt installed? How can I get those values, without monitoring all VMs directly? oVirt Version we use: 4.1.1.8-1.el7.centos BR Florian

3 12

Reg: Ovirt mouse not responding
by syedquadeer＠ctel.in 05 Dec '17

05 Dec '17

Dear Team, I am using Ovirt 3.x on centos 3 node cluster and in that Ubuntu 14.04 64bit vm's are installed. But the end users, who are using this vm' s are facing some issue daily and issues are mentioned below, 1. Keyboard will not respond in middle automatically and after checking log file in vm, it show pmouse sync issue. 2. If Vm is restarted it is giving black screen, then Vm need to power off and start again. Please provide solution for above issues. Thanks in advance... -- Thanks & Regards, Syed Abdul Qadeer. 7660022818.

1 1

Re: [ovirt-users] iSCSI domain on 4kn drives
by Martijn Grendelman 13 Nov '17

13 Nov '17

--------------DE48748F7C67E1FABE46EEAF Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit Op 7-8-2016 om 8:19 schreef Yaniv Kaul: > > On Fri, Aug 5, 2016 at 4:42 PM, Martijn Grendelman > <martijn.grendelman(a)isaac.nl <mailto:martijn.grendelman@isaac.nl>> wrote: > > Op 4-8-2016 om 18:36 schreef Yaniv Kaul: >> On Thu, Aug 4, 2016 at 11:49 AM, Martijn Grendelman >> <martijn.grendelman(a)isaac.nl >> <mailto:martijn.grendelman@isaac.nl>> wrote: >> >> Hi, >> >> Does oVirt support iSCSI storage domains on target LUNs using >> a block >> size of 4k? >> >> >> No, we do not - not if it exposes 4K blocks. >> Y. > > Is this on the roadmap? > > > Not in the short term roadmap. > Of course, patches are welcome. It's mainly in VDSM. > I wonder if it'll work in NFS. > Y. I don't think I ever replied to this, but I can confirm that in RHEV 3.6 it works with NFS. Best regards, Martijn. --------------DE48748F7C67E1FABE46EEAF Content-Type: text/html; charset="utf-8" Content-Transfer-Encoding: 7bit <html> <head> <meta content="text/html; charset=utf-8" http-equiv="Content-Type"> </head> <body bgcolor="#FFFFFF" text="#000000"> Op 7-8-2016 om 8:19 schreef Yaniv Kaul:<br> <blockquote cite="mid:280cfbd3a16ad1b76cc7de56bda88f45,CAJgorsbJHLV1e3fH4b4AR3GBp1oi44fDhfeii+PQ1iY1RwUStw@mail.gmail.com" type="cite"> <div dir="ltr"><br> <div class="gmail_extra">On Fri, Aug 5, 2016 at 4:42 PM, Martijn Grendelman <span dir="ltr"><<a moz-do-not-send="true" href="mailto:martijn.grendelman@isaac.nl" target="_blank">martijn.grendelman(a)isaac.nl</a>></span> wrote:<br> <div class="gmail_quote"> <blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"> <div bgcolor="#FFFFFF" text="#000000"> Op 4-8-2016 om 18:36 schreef Yaniv Kaul:<br> <blockquote type="cite"> <div dir="ltr"> <div class="gmail_extra"> <div class="gmail_quote"><span class="">On Thu, Aug 4, 2016 at 11:49 AM, Martijn Grendelman <span dir="ltr"><<a moz-do-not-send="true" href="mailto:martijn.grendelman@isaac.nl" target="_blank">martijn.grendelman(a)isaac.nl</a>></span> wrote:<br> </span><span class=""> <blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi,<br> <br> Does oVirt support iSCSI storage domains on target LUNs using a block<br> size of 4k?<br> </blockquote> <div><br> </div> </span><span class=""> <div>No, we do not - not if it exposes 4K blocks.</div> <div>Y.</div> </span></div> </div> </div> </blockquote> <br> Is this on the roadmap?<br> </div> </blockquote> <div><br> </div> <div>Not in the short term roadmap.</div> <div>Of course, patches are welcome. It's mainly in VDSM.</div> <div>I wonder if it'll work in NFS.</div> <div>Y.</div> </div> </div> </div> </blockquote> <br> I don't think I ever replied to this, but I can confirm that in RHEV 3.6 it works with NFS.<br> <br> Best regards,<br> Martijn.<br> </body> </html> --------------DE48748F7C67E1FABE46EEAF--

4 4

Re: [ovirt-users] How to import a qcow2 disk into ovirt
by Martín Follonier 04 Oct '17

04 Oct '17

Hi, I've done all the recommendations in this thread, and I'm still getting the "Paused by System" message just after the transfer starts. Honestly I don't know were else to look at, cause I don't find any log entry or packet capture that give me a hint about what is happening. I'll appreciate any help! Thank you in advance! Regards Martin On Thu, Sep 1, 2016 at 5:01 PM, Amit Aviram <aavi...(a)redhat.com> wrote: > You can do both, > Through the database, the table is "vdc_options". change "option_value" > where "option_name" = 'ImageProxyAddress' . > > On Thu, Sep 1, 2016 at 4:56 PM, Gianluca Cecchi <gianluca.cec...(a)gmail.com > > wrote: > >> On Thu, Sep 1, 2016 at 3:53 PM, Amit Aviram <aavi...(a)redhat.com> wrote: >> >>> You can just replace this value in the DB and change it to the right >>> FQDN, it is a config value named "ImageProxyAddress". replace "localhost" >>> with the right address (notice that the port is there too). >>> >>> If this will keep happen after users will have the latest version, we >>> will have to open a bug and fix whatever causes the URL to be "localhost". >>> >>> >> Do you mean through "engine-config" or directly into database? >> In this second case which is the table involved? >> >> Gianluca >> > > [root@ractorshe bin]# systemctl stop ovirt-imageio-proxy engine=# select * from vdc_options where option_name='ImageProxyAddress'; option_id | option_name | option_value | version -----------+-------------------+-----------------+--------- 950 | ImageProxyAddress | localhost:54323 | general (1 row) engine=# update vdc_options set option_value='ractorshe.mydomain:54323' where option_name='ImageProxyAddress'; UPDATE 1 engine=# select * from vdc_options where option_name='ImageProxyAddress'; option_id | option_name | option_value | version -----------+-------------------+--------------------------------------+--------- 950 | ImageProxyAddress | ractorshe.mydomain:54323 | general (1 row) engine=# engine=# select * from vdc_options where option_name='ImageProxyAddress'; option_id | option_name | option_value | version -----------+-------------------+--------------------------------------+--------- 950 | ImageProxyAddress | ractorshe.mydomain:54323 | general (1 row) systemctl stop ovirt-engine (otherwise it remained localhost) systemctl start ovirt-engine systemctl start ovirt-imageio-proxy Now transfer is ok. I tried a qcow2 disck configured as 40Gb but containing about 1.6Gb of data. I'm going to connect it to a VM and see if all is ok also from a contents point of view. Gianluca _______________________________________________ Users mailing listUsers@ovirt.orghttp://lists.ovirt.org/mailman/listinfo/users

5 6