Out-of-sync networks can only be detached
by Sakhi Hadebe
Hi,
I have a 3-node oVirt cluster. I have configured 2 logical networks:
ovirtmgmt and public. Public logical network is attached in only 2 nodes
and failing to attach on the 3rd node with the below error
Invalid operation, out-of-sync network 'public' can only be detached.
Please have been stuck on this for almost the whole day now. How do I fix
this error?
--
Regards,
Sakhi Hadebe
2 years, 2 months
Network Address Change
by Paul.LKW
Hi All:
I just has a case, I need to change the oVirt host and engine IP address
due to data center decommission I checked in the hosted-engine host
there are some files I could change ;
in ovirt-hosted-engine/hosted-engine.conf
ca_subject="O=simple.com, CN=1.2.3.4"
gateway=1.2.3.254
and of course I need to change the ovirtmgmt interface IP too, I think
just change the above line could do the tick, but where could I change
the other host IP in the cluster ?
I think I have to be lost all the host as once changed the hosted-engine
host IP as it is in diff. sub net.
Does there any command line tools could do that or someone has such
experience could share?
Best Regards,
Paul.LKW
2 years, 4 months
VM HostedEngine is down with error
by souvaliotimaria＠mail.com
Hello everyone,
I have a replica 2 + arbiter installation and this morning the Hosted Engine gave the following error on the UI and resumed on a different node (node3) than the one it was originally running(node1). (The original node has more memory than the one it ended up, but it had a better memory usage percentage at the time). Also, the only way I discovered the migration had happened and there was an Error in Events, was because I logged in the web interface of ovirt for a routine inspection. Βesides that, everything was working properly and still is.
The error that popped is the following:
VM HostedEngine is down with error. Exit message: internal error: qemu unexpectedly closed the monitor:
2020-09-01T06:49:20.749126Z qemu-kvm: warning: All CPU(s) up to maxcpus should be described in NUMA config, ability to start up with partial NUMA mappings is obsoleted and will be removed in future
2020-09-01T06:49:20.927274Z qemu-kvm: -device virtio-blk-pci,iothread=iothread1,scsi=off,bus=pci.0,addr=0x7,drive=drive-ua-d5de54b6-9f8e-4fba-819b-ebf6780757d2,id=ua-d5de54b6-9f8e-4fba-819b-ebf6780757d2,bootindex=1,write-cache=on: Failed to get "write" lock
Is another process using the image?.
Which from what I could gather concerns the following snippet from the HostedEngine.xml and it's the virtio disk of the Hosted Engine:
<disk type='file' device='disk' snapshot='no'>
<driver name='qemu' type='raw' cache='none' error_policy='stop' io='threads' iothread='1'/>
<source file='/var/run/vdsm/storage/80f6e393-9718-4738-a14a-64cf43c3d8c2/d5de54b6-9f8e-4fba-819b-ebf6780757d2/a48555f4-be23-4467-8a54-400ae7baf9d7'>
<seclabel model='dac' relabel='no'/>
</source>
<target dev='vda' bus='virtio'/>
<serial>d5de54b6-9f8e-4fba-819b-ebf6780757d2</serial>
<alias name='ua-d5de54b6-9f8e-4fba-819b-ebf6780757d2'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/>
</disk>
I've tried looking into the logs and the sar command but I couldn't find anything to relate with the above errors and determining the reason for it to happen. Is this a Gluster or a QEMU problem?
The Hosted Engine was manually migrated five days before on node1.
Is there a standard practice I could follow to determine what happened and secure my system?
Thank you very much for your time,
Maria Souvalioti
2 years, 11 months
OVS switch type for hosted-engine
by Devin A. Bougie
Is it possible to setup a hosted engine using the OVS switch type instead of Legacy? If it's not possible to start out as OVS, instructions for switching from Legacy to OVS after the fact would be greatly appreciated.
Many thanks,
Devin
3 years
USB3 redirection
by Rik Theys
Hi,
I'm trying to assign a USB3 controller to a CentOS 7.4 VM in oVirt 4.1
with USB redirection enabled.
I've created the following file in /etc/ovirt-engine/osinfo.conf.d:
01-usb.properties with content
os.other.devices.usb.controller.value = nec-xhci
and have restarted ovirt-engine.
If I disable USB-support in the web interface for the VM, the xhci
controller is added to the VM (I can see it in the qemu-kvm
commandline), but usb redirection is not available.
If I enable USB-support in the UI, no xhci controller is added (only 4
uhci controllers).
Is there a way to make the controllers for usb redirection xhci controllers?
Regards,
Rik
--
Rik Theys
System Engineer
KU Leuven - Dept. Elektrotechniek (ESAT)
Kasteelpark Arenberg 10 bus 2440 - B-3001 Leuven-Heverlee
+32(0)16/32.11.07
----------------------------------------------------------------
<<Any errors in spelling, tact or fact are transmission errors>>
3 years
OVN routing and firewalling in oVirt
by Gianluca Cecchi
Hello,
how do we manage routing between different OVN networks in oVirt?
And between OVN networks and physical ones?
Based on architecture read here:
http://openvswitch.org/support/dist-docs/ovn-architecture.7.html
I see terms for logical routers and gateway routers respectively but how to
apply to oVirt configuration?
Do I have to choose between setting up a specialized VM or a physical one:
is it applicable/advisable to put on oVirt host itself the gateway
functionality?
Is there any security policy (like security groups in Openstack) to
implement?
Thanks,
Gianluca
3 years
Install hosted-engine - Task Get local VM IP failed
by florentl
Hi all,
I try to install hosted-engine on node : ovirt-node-ng-4.2.3-0.20180518.
Every times I get stuck on :
[ ERROR ] fatal: [localhost]: FAILED! => {"attempts": 50, "changed":
true, "cmd": "virsh -r net-dhcp-leases default | grep -i
00:16:3e:6c:5a:91 | awk '{ print $5 }' | cut -f1 -d'/'", "delta":
"0:00:00.108872", "end": "2018-06-01 11:17:34.421769", "rc": 0, "start":
"2018-06-01 11:17:34.312897", "stderr": "", "stderr_lines": [],
"stdout": "", "stdout_lines": []}
I tried with static IP Address and with DHCP but both failed.
To be more specific, I installed three nodes, deployed glusterfs with
the wizard. I'm in a nested virtualization environment for this lab
(Vmware Esxi Hypervisor).
My node IP is : 192.168.176.40 / and I want the hosted-engine vm has
192.168.176.43.
Thanks,
Florent
3 years, 2 months
Host needs to be reinstalled after configuring power management
by Andrew DeMaria
Hi,
I am running ovirt 4.3 and have found the following action item immediately
after configuring power management for a host:
Host needs to be reinstalled as important configuration changes were
applied on it.
The thing is - I've just freshly installed this host and it seems strange
that I need to reinstall it.
Is there a better way to install a host and configure power management
without having to reinstall it after?
Thanks,
Andrew
3 years, 3 months
Import an exported VM using Ansible
by paolo＠airaldi.it
Hello everybody!
I'm trying to automate a copy of a VM from one Datacenter to another using an Ansible.playbook.
I'm able to:
- Create a snapshot of the source VM
- create a clone from the snapshot
- remove the snapshot
- attach an Export Domain
- export the clone to the Export Domain
- remove the clone
- detach the Export domain from the source Datacenter and attach to the destination.
Unfortunately I cannot find a module to:
- import the VM from the Export Domain
- delete the VM image from the Export Domain.
Any hint on how to do that?
Thanks in advance. Cheers.
Paolo
PS: if someone is interested I can share the playbook.
3 years, 3 months
