October 2019 - Devel - oVirt List Archives

How to remove ovirtmgmt network interface in centOS
by Prajith Kesava Prasad 23 Oct '19

23 Oct '19

Hey everyone, Could someone please point me in the right direction?. Im unable to remove network interface ovirtmgmt, commands like ifdown results in a state where the ip is unreachable and a manual network restart had to be done to bring it back to normal. could someone help me with removing ovirtmgmt network in centos? ___________________________________________________________________ 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master ovirtmgmt state UP group default qlen 1000 link/ether 00:1a:4a:16:01:9c brd ff:ff:ff:ff:ff:ff 23: ;vdsmdummy;: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether 66:66:f1:c4:52:c7 brd ff:ff:ff:ff:ff:ff 24: ovs-system: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether fe:aa:a4:0d:7a:31 brd ff:ff:ff:ff:ff:ff 25: br-int: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether ba:fd:da:db:29:44 brd ff:ff:ff:ff:ff:ff 147: ovirtmgmt: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000 link/ether 00:1a:4a:16:01:9c brd ff:ff:ff:ff:ff:ff inet 10.70.43.190/22 brd 10.70.43.255 scope global dynamic ovirtmgmt valid_lft 85952sec preferred_lft 85952sec inet6 2620:52:0:4628:21a:4aff:fe16:19c/64 scope global mngtmpaddr dynamic valid_lft 2591937sec preferred_lft 604737sec inet6 fe80::21a:4aff:fe16:19c/64 scope link valid_lft forever preferred_lft forever _________________________________________________________________________ Thanks, Prajith

3 2

Set host as SPM
by scott.fitzgerald＠oracle.com 23 Oct '19

23 Oct '19

System currently has 1 DC, 1 cluster, 2 active hosts in cluster and 1 domain. Host1 is SPM, through UI I can set Host2 to SPM, Host1 becomes Non-SPM host. Through the SDK I can use SpmBuilder spmBuilder = new SpmBuilder().priority(7); sysService.hostsService().hostService(host.id()).update().host(host().spm(spmBuilder)).send(); to update host SPM priority. I cannot find a way to use the SDK to change the Host to SPM mode directly, despite using spm().status in a similar manner as above for the priority. How can I achieve this? TIA

2 2

Processing Conflict: sos-3.7-6.el7.centos.noarch conflicts vdsm <= 4.30.17
by trunet-ovirt＠wsartori.com 23 Oct '19

23 Oct '19

Hello all, good afternoon. I'm new here, my name is Wagner and I live in The Netherlands. I inherited an old 4.2 oVirt cluster and I'm in process of adding new CentOS hypervisors to it. Sadly this isn't working well due to a conflict in vdsm and sos. I did some research, and found this[1] on RedHat and also this thread[2] and this gerrit review[3]. Looks like the sos package now contains vdsm sos module and this needs to be removed on 4.2 version. Current sos package conflicts[4] with vdsm <= 4.30.17. The way forward (if this is accepted by you and CentOS) would be to release a new 4.2 version, and change the conflict on sos package to accept this new 4.2 vdsm version. I can help with pull requests, building packages (.src.rpm) or whatever. What you guys think about it? [1]: https://bugzilla.redhat.com/show_bug.cgi?id=1714509 [2]: https://lists.ovirt.org/archives/list/devel@ovirt.org/thread/AGIX5H4EJQ66FU… [3]: https://gerrit.ovirt.org/#/c/100576/ [4]: https://git.centos.org/rpms/sos/blob/c7/f/SPECS/sos.spec#_20 Best regards, Wagner Sartori Junior

3 2

SSL: UNKNOWN_PROTOCOL error when running Lago init during System Tests setup.
by raymond.francis＠oracle.com 23 Oct '19

23 Oct '19

Trying to nail down the setup in the System Test Setup guide https://ovirt-system-tests.readthedocs.io/en/latest/general/installation/in… and i come to an issue when i run the suite. lago init /Ray/ovirt-system-tests/deployment-basic-suite-4.3 /Ray/ovirt-system-tests/basic-suite-4.3/LagoInitFile --template-repo-path /Ray/ovirt-system-tests/basic-suite-4.3/template-repo.json @ Initialize and populate prefix: # Initialize prefix: * Create prefix dirs: * Create prefix dirs: Success (in 0:00:00) * Generate prefix uuid: * Generate prefix uuid: Success (in 0:00:00) * Create ssh keys: * Create ssh keys: Success (in 0:00:00) * Tag prefix as initialized: * Tag prefix as initialized: Success (in 0:00:00) # Initialize prefix: Success (in 0:00:00) # Create disks for VM lago-basic-suite-4-3-engine: * Create disk root: - Template phx_repo:el7.6-base-5:v1 not in cache, downloading - Download image el7.6-base-5: - Download image el7.6-base-5: ERROR (in 0:00:00) * Create disk root: ERROR (in 0:00:00) # Create disks for VM lago-basic-suite-4-3-engine: ERROR (in 0:00:00) # Missing current link, setting it to default @ Initialize and populate prefix: ERROR (in 0:00:01) Error occured, aborting Traceback (most recent call last): File "/usr/lib/python2.7/site-packages/lago/cmd.py", line 969, in main cli_plugins[args.verb].do_run(args) File "/usr/lib/python2.7/site-packages/lago/plugins/cli.py", line 184, in do_run self._do_run(**vars(args)) File "/usr/lib/python2.7/site-packages/lago/cmd.py", line 194, in do_init do_build=not skip_build, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1113, in virt_conf_from_stream do_build=do_build File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1228, in virt_conf template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1133, in _prepare_domains_images template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1155, in _prepare_domain_image template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1183, in _create_disks template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 669, in _create_disk template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 798, in _handle_template template_repo=template_repo, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 935, in _handle_lago_template template_store.download(template_version) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 645, in download temp_ver.download(temp_dest) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 528, in download self._source.download_image(self._handle, destination) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 196, in download_image self.open_url(url=handle, dest=dest) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 148, in open_url dest=dest, File "/usr/lib/python2.7/site-packages/lago/templates.py", line 153, in open_url response = urllib.urlopen(full_url) File "/usr/lib64/python2.7/urllib.py", line 87, in urlopen return opener.open(url) File "/usr/lib64/python2.7/urllib.py", line 210, in open return getattr(self, name)(url) File "/usr/lib64/python2.7/urllib.py", line 439, in open_https h.endheaders(data) File "/usr/lib64/python2.7/httplib.py", line 1052, in endheaders self._send_output(message_body) File "/usr/lib64/python2.7/httplib.py", line 890, in _send_output self.send(msg) File "/usr/lib64/python2.7/httplib.py", line 852, in send self.connect() File "/usr/lib64/python2.7/httplib.py", line 1275, in connect server_hostname=sni_hostname) File "/usr/lib64/python2.7/ssl.py", line 348, in wrap_socket _context=self) File "/usr/lib64/python2.7/ssl.py", line 609, in __init__ self.do_handshake() File "/usr/lib64/python2.7/ssl.py", line 831, in do_handshake self._sslobj.do_handshake() IOError: [Errno socket error] [SSL: UNKNOWN_PROTOCOL] unknown protocol (_ssl.c:618)

1 1

ovirt-system-tests network suite
by Miguel Duarte de Mora Barroso 23 Oct '19

23 Oct '19

I'm trying to run OST network suite locally, and it is failing w/ the following error [0]. The build can be found in [1]. Any guidance / clue ? [0] - http://pastebin.test.redhat.com/807736 [1] - https://jenkins.ovirt.org/job/ovirt-system-tests_manual/5835/

2 2

SSL: UNKNOWN_PROTOCOL error when running Lago init during System Tests setup.
by raymond.francis＠oracle.com 21 Oct '19

21 Oct '19

Trying to nail down the setup in the System Test Setup guide https://ovirt-system-tests.readthedocs.io/en/latest/general/installation/in… and i come to an issue when i run the suite. lago init /Ray/ovirt-system-tests/deployment-basic-suite-4.3 /Ray/ovirt-system-tests/basic-suite-4.3/LagoInitFile --template-repo-path /Ray/ovirt-system-tests/basic-suite-4.3/template-repo.json @ Initialize and populate prefix: # Initialize prefix: * Create prefix dirs: * Create prefix dirs: Success (in 0:00:00) * Generate prefix uuid: * Generate prefix uuid: Success (in 0:00:00) * Create ssh keys: * Create ssh keys: Success (in 0:00:00) * Tag prefix as initialized: * Tag prefix as initialized: Success (in 0:00:00) # Initialize prefix: Success (in 0:00:00) # Create disks for VM lago-basic-suite-4-3-engine: * Create disk root: - Template phx_repo:el7.6-base-5:v1 not in cache, downloading - Download image el7.6-base-5: - Download image el7.6-base-5: ERROR (in 0:00:00) * Create disk root: ERROR (in 0:00:00) # Create disks for VM lago-basic-suite-4-3-engine: ERROR (in 0:00:00) # Missing current link, setting it to default @ Initialize and populate prefix: ERROR (in 0:00:01) Error occured, aborting Traceback (most recent call last): File "/usr/lib/python2.7/site-packages/lago/cmd.py", line 969, in main cli_plugins[args.verb].do_run(args) File "/usr/lib/python2.7/site-packages/lago/plugins/cli.py", line 184, in do_run self._do_run(**vars(args)) File "/usr/lib/python2.7/site-packages/lago/cmd.py", line 194, in do_init do_build=not skip_build, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1113, in virt_conf_from_stream do_build=do_build File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1228, in virt_conf template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1133, in _prepare_domains_images template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1155, in _prepare_domain_image template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 1183, in _create_disks template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 669, in _create_disk template_store=template_store, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 798, in _handle_template template_repo=template_repo, File "/usr/lib/python2.7/site-packages/lago/prefix.py", line 935, in _handle_lago_template template_store.download(template_version) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 645, in download temp_ver.download(temp_dest) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 528, in download self._source.download_image(self._handle, destination) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 196, in download_image self.open_url(url=handle, dest=dest) File "/usr/lib/python2.7/site-packages/lago/templates.py", line 148, in open_url dest=dest, File "/usr/lib/python2.7/site-packages/lago/templates.py", line 153, in open_url response = urllib.urlopen(full_url) File "/usr/lib64/python2.7/urllib.py", line 87, in urlopen return opener.open(url) File "/usr/lib64/python2.7/urllib.py", line 210, in open return getattr(self, name)(url) File "/usr/lib64/python2.7/urllib.py", line 439, in open_https h.endheaders(data) File "/usr/lib64/python2.7/httplib.py", line 1052, in endheaders self._send_output(message_body) File "/usr/lib64/python2.7/httplib.py", line 890, in _send_output self.send(msg) File "/usr/lib64/python2.7/httplib.py", line 852, in send self.connect() File "/usr/lib64/python2.7/httplib.py", line 1275, in connect server_hostname=sni_hostname) File "/usr/lib64/python2.7/ssl.py", line 348, in wrap_socket _context=self) File "/usr/lib64/python2.7/ssl.py", line 609, in __init__ self.do_handshake() File "/usr/lib64/python2.7/ssl.py", line 831, in do_handshake self._sslobj.do_handshake() IOError: [Errno socket error] [SSL: UNKNOWN_PROTOCOL] unknown protocol (_ssl.c:618)

1 0

Unable to Build (Unable to find 'org/ovirt/engine/ui/webadmin/WebAdmin.gwt.xml)
by Ritesh Chikatwar 21 Oct '19

21 Oct '19

Hey Guys, Please do let me know what is causing me this issue. *NOTE:* I have not changed anything in this file. info register aspect org.ovirt.engine.ui.gwtaop.DontPrune [INFO] Loading inherited module 'org.ovirt.engine.ui.webadmin.WebAdmin' *[INFO] [ERROR] Unable to find 'org/ovirt/engine/ui/webadmin/WebAdmin.gwt.xml' on your classpath; could be a typo, or maybe you forgot to include a classpath entry for source?* [INFO] ------------------------------------------------------------------------ [INFO] Reactor Summary for WebAdmin 4.4.0-SNAPSHOT: [INFO] [INFO] WebAdmin ........................................... FAILURE [ 1.548 s] [INFO] oVirt Server EAR ................................... SKIPPED [INFO] ovirt-engine maven make ............................ SKIPPED [INFO] ------------------------------------------------------------------------ [INFO] BUILD FAILURE [INFO] ------------------------------------------------------------------------ [INFO] Total time: 1.918 s [INFO] Finished at: 2019-10-21T11:30:20+05:30 [INFO] ------------------------------------------------------------------------ [ERROR] Failed to execute goal org.codehaus.mojo:gwt-maven-plugin:2.8.0:compile (default-cli) on project webadmin: Command [[ [ERROR] /bin/sh -c '/usr/local/jdk-11.0.2/bin/java' '-javaagent:/home/ritesh/.m2/repository/org/aspectj/aspectjweaver/1.9.3.RC1/aspectjweaver-1.9.3.RC1.jar' '-Dgwt.jjs.permutationWorkerFactory=com.google.gwt.dev.ThreadedPermutationWorkerFactory' '-Dgwt.jjs.maxThreads=4' '-Djava.io.tmpdir=/home/ritesh/build/ovirt-engine/frontend/webadmin/modules/webadmin/target/tmp' '-Djava.util.prefs.systemRoot=/home/ritesh/build/ovirt-engine/frontend/webadmin/modules/webadmin/target/tmp' '-Djava.util.prefs.userRoot=/home/ritesh/build/ovirt-engine/frontend/webadmin/modules/webadmin/target/tmp' '-Djava.util.logging.config.class=org.ovirt.engine.ui.gwtaop.JavaLoggingConfig' '-Xms1024M' '-Xmx8192M' '-Dgwt.dontPrune=org\.ovirt\.engine\.core\.(common|compat)\..*' 'com.google.gwt.dev.Compiler' '-logLevel' 'INFO' '-war' '/home/ritesh/build/ovirt-engine/frontend/webadmin/modules/webadmin/target/webadmin-4.4.0-SNAPSHOT' '-localWorkers' '8' '-failOnError' '-XfragmentCount' '-1' '-sourceLevel' 'auto' '-gen' '/home/ritesh/build/ovirt-engine/frontend/webadmin/modules/webadmin/gen' 'org.ovirt.engine.ui.webadmin.WebAdmin' [ERROR] ]] failed with status 1. Thanks And Regards Ritesh Chikatwar

1 0

[oVirt] [CQ weekly status] [20-10-2019]
by Dusan Fodor 20 Oct '19

20 Oct '19

Hi, This mail is to provide the current status of CQ and allow people to review status before and after the weekend. Please refer to below colour map for further information on the meaning of the colours. *CQ-4.3*: GREEN (#1) Last failure was on 17-10 for ovirt-node-ng-image due to an issue with host it was building on. Next run passed well. . *CQ-Master:* YELLOW (#1 Last failure was on 18-10 caused by known, random add storage domain failure (test issue). Current running jobs for 4.3 [1] and master [2] can be found here: [1] https://jenkins.ovirt.org/view/Change%20queue%20jobs/job/ovirt-4.3_change-q… [2] http://jenkins.ovirt.org/view/Change%20queue%20jobs/job/ovirt-master_change… Have a nice week! Dusan ------------------------------------------------------------------------------------------------------------------- COLOUR MAP Green = job has been passing successfully ** green for more than 3 days may suggest we need a review of our test coverage 1. 1-3 days GREEN (#1) 2. 4-7 days GREEN (#2) 3. Over 7 days GREEN (#3) Yellow = intermittent failures for different projects but no lasting or current regressions ** intermittent would be a healthy project as we expect a number of failures during the week ** I will not report any of the solved failures or regressions. 1. Solved job failures YELLOW (#1) 2. Solved regressions YELLOW (#2) Red = job has been failing ** Active Failures. The colour will change based on the amount of time the project/s has been broken. Only active regressions would be reported. 1. 1-3 days RED (#1) 2. 4-7 days RED (#2) 3. Over 7 days RED (#3) _______________________________________________ Devel mailing list -- devel(a)ovirt.org To unsubscribe send an email to devel-leave(a)ovirt.org Privacy Statement: https://www.ovirt.org/site/privacy-policy/ oVirt Code of Conduct: https://www.ovirt.org/community/about/community-guidelines/ List Archives: https://lists.ovirt.org/archives/list/devel@ovirt.org/message/YCNCKRK3G4EJX…

1 0

Add existing Affinity Label to Host
by scott.fitzgerald＠oracle.com 18 Oct '19

18 Oct '19

As the title, have tried to add it using sysService.hostsService().hostService(hostID).affinityLabelsService().add().label(sysService.affinityLabelsService().labelService(labelID).get().send().label()).send(); and similar variants with no luck. TIA

2 2

Retrieve cluster status using the SDK
by Jamie Holohan 18 Oct '19

18 Oct '19

Using the SDK how can I retrieve a clusters (network) status. I am able to retrieve a cluster object using code like this: Cluster cluster = sysService.clustersService().clusterService(DataCenterUtils.getClusterObjectFromName(sysService, DEFAULT_CLUSTER_NAME).id()).get().send().cluster(); However I cannot see any variables associated with this object type that relate to its Network Status. The information i'm referring to can be found on the UI after creating a custom network. Starting on the left panel Navigate to Network -> Networks -> Custom Network -> Clusters Tab

2 1

vdsm has been tagged (v4.30.34)
by Milan Zamazal 17 Oct '19

17 Oct '19

1 0

ovirt-engine has been tagged (ovirt-engine-4.3.7.0)
by Piotr Kliczewski 17 Oct '19

17 Oct '19

1 0

Clarifications on support@
by Marc Dequènes (Duck) 16 Oct '19

16 Oct '19

Quack, We do as a community provide help on the MLs and reply to JIRA tickets but there is no customer support as it is not a product but a community project. Historically, probably for some other purpose, support@ was created, but noone remembers why. Anyway, the alias redirected to postmaster so it was not very useful. There was also a ML which could not receive mails because of the alias but probably got noticed in the new ML UI when we migrated. Recently more people subscribed and posted requests using the UI. After discussing with the infra team, and to avoid confusion and unreplied requests on this channel, we decided to remove it. I thus unsubscribed people from the list so that they would notice it and then purged the list and alias. Regards. \_o<

1 0

Problem with vdsm 'make check'
by Kaustav Majumder 15 Oct '19

15 Oct '19

Hi, I am having an issue running make check on vdsm master. ` if [ -n "$NOSE_WITH_COVERAGE" ]; then \ mv .coverage .coverage-nose-py27; \ fi Traceback (most recent call last): File "../tests/testrunner.py", line 70, in <module> from vdsm import constants File "/home/kmajumde/work/git/vdsm/lib/vdsm/constants.py", line 29, in <module> from vdsm.common.constants import * # NOQA: F401, F403 ` Am I missing something? Do I need to run tests differently? -- Thanks, Kaustav Majumder

5 14

Re: Problem with vdsm 'make check'
by Prajith Kesava Prasad 15 Oct '19

15 Oct '19

hey, even im facing a issue with make check, i have installed all the libraries, the following occurs on fedora 29, IDE:Pycharm could some one help me with this? Thanks, Prajith Kesava Prasad

2 3

Need to install lago plugin but get circular issue with dependancies
by raymond.francis＠oracle.com 15 Oct '19

15 Oct '19

Having setup Lago and wishing to run the system tests ./run_suite.sh basic-suite-4.3 I get the below error which leads to a circular issue... @ Initialize and populate prefix: ERROR (in 0:00:00) Unknown VM type: ovirt-engine, available types: default, maybe you need to install lago plugin + on_exit + [[ 2 -ne 0 ]] + logger.error 'on_exit: Exiting with a non-zero status' + logger.log ERROR 'on_exit: Exiting with a non-zero status' + set +x 2019-10-14 18:09:43.202994574+0100 run_suite.sh::on_exit::ERROR:: on_exit: Exiting with a non-zero status + logger.info 'Dumping lago env status' + logger.log INFO 'Dumping lago env status' + set +x 2019-10-14 18:09:43.207157153+0100 run_suite.sh::on_exit::INFO:: Dumping lago env status + env_status + cd /root/pip-19.2.3/ovirt-system-tests/deployment-basic-suite-4.3 ./run_suite.sh: line 265: cd: /root/pip-19.2.3/ovirt-system-tests/deployment-basic-suite-4.3: No such file or directory + lago status Unable to find workdir in /root/pip-19.2.3/ovirt-system-tests + cd - When i try to install lago, i get this Error: Package: python-lago-0.46.0-1.el7.noarch (lago) Requires: qemu-kvm-rhev >= 2.1.2 Error: Package: python-lago-0.46.0-1.el7.noarch (lago) Requires: qemu-img-rhev >= 2.1.2 Trying to install either gets this [root@dub-mgrfarm113 ovirt-system-tests]# yum install -y qemu-img-rhev Loaded plugins: ulninfo, versionlock Package 10:qemu-img-ev-2.6.0-28.el7_3.3.1.x86_64 is obsoleted by 15:qemu-3.1.0-5.el7.x86_64 which is already installed Nothing to do [root@dub-mgrfarm113 ovirt-system-tests]# yum install -y qemu-kvm-rhev Loaded plugins: ulninfo, versionlock Package 10:qemu-kvm-ev-2.6.0-28.el7_3.3.1.x86_64 is obsoleted by 15:qemu-3.1.0-5.el7.x86_64 which is already installed Nothing to do Chicken and egg issue,any ideas?

2 2

Need to install lago plugin but get circular issue with dependancies
by raymond.francis＠oracle.com 14 Oct '19

14 Oct '19

Having setup Lago and wishing to run the system tests ./run_suite.sh basic-suite-4.3 I get the below error which leads to a circular issue... @ Initialize and populate prefix: ERROR (in 0:00:00) Unknown VM type: ovirt-engine, available types: default, maybe you need to install lago plugin + on_exit + [[ 2 -ne 0 ]] + logger.error 'on_exit: Exiting with a non-zero status' + logger.log ERROR 'on_exit: Exiting with a non-zero status' + set +x 2019-10-14 18:09:43.202994574+0100 run_suite.sh::on_exit::ERROR:: on_exit: Exiting with a non-zero status + logger.info 'Dumping lago env status' + logger.log INFO 'Dumping lago env status' + set +x 2019-10-14 18:09:43.207157153+0100 run_suite.sh::on_exit::INFO:: Dumping lago env status + env_status + cd /root/pip-19.2.3/ovirt-system-tests/deployment-basic-suite-4.3 ./run_suite.sh: line 265: cd: /root/pip-19.2.3/ovirt-system-tests/deployment-basic-suite-4.3: No such file or directory + lago status Unable to find workdir in /root/pip-19.2.3/ovirt-system-tests + cd - When i try to install lago, i get this Error: Package: python-lago-0.46.0-1.el7.noarch (lago) Requires: qemu-kvm-rhev >= 2.1.2 Error: Package: python-lago-0.46.0-1.el7.noarch (lago) Requires: qemu-img-rhev >= 2.1.2 Trying to install either gets this [root@dub-mgrfarm113 ovirt-system-tests]# yum install -y qemu-img-rhev Loaded plugins: ulninfo, versionlock Package 10:qemu-img-ev-2.6.0-28.el7_3.3.1.x86_64 is obsoleted by 15:qemu-3.1.0-5.el7.x86_64 which is already installed Nothing to do [root@dub-mgrfarm113 ovirt-system-tests]# yum install -y qemu-kvm-rhev Loaded plugins: ulninfo, versionlock Package 10:qemu-kvm-ev-2.6.0-28.el7_3.3.1.x86_64 is obsoleted by 15:qemu-3.1.0-5.el7.x86_64 which is already installed Nothing to do Chicken and egg issue,any ideas?

1 0

Checkstyle Java 11 false positives.
by Ales Musil 14 Oct '19

14 Oct '19

Hi, just found out that checkstyle is not completely aware of Java 11 features. Completely valid syntax e.g. "var attachmentsToRemove = new HashSet<Guid>();" is marked with error: "DiamondOperator: Diamond operator should be used" What can we do about this? Thanks. Regards, Ales -- Ales Musil Associate Software Engineer - RHV Network Red Hat EMEA <https://www.redhat.com> amusil(a)redhat.com IM: amusil <https://red.ht/sig>

3 3

[VDSM] CentOS 8 build on Travis - only 3 tests fail
by Nir Soffer 11 Oct '19

11 Oct '19

I added centos-8 docker image: https://hub.docker.com/r/ovirtorg/vdsm-test-centos-8 And centos-8 build in Travis: https://travis-ci.org/nirs/vdsm/jobs/596270609 After fixing 22 tests trying to run /usr/bin/python2, we have only 3 failing tests in lib-py36: lib/hooks_test.py .....................x......F.............. [ 50%] ssl_test.py ...........FF... [100%] Marcin already handled the ssl tests in: https://gerrit.ovirt.org/c/103812/ I'm not sue why the hook test fail. Please review: https://gerrit.ovirt.org/q/topic:py3+is:open+owner:%2522Nir+Soffer+%253Cnso… Nir

3 5

Set host as SPM
by scott.fitzgerald＠oracle.com 11 Oct '19

11 Oct '19

I have managed to set a host SPM priority using SpmBuilder spmBuilder = new SpmBuilder().priority(7); sysService.hostsService().hostService(host.id()).update().host(host().spm(spmBuilder)).send(); However I cannot use similar code to set a Host to SPM. I currently have 2 active hosts in the same cluster in my system. Through the UI I can move SPM back and forth between them, but it is not working in the SDK. Any help appreciated.

1 0

Ovirt SDK: Problems retrieving the storage domain, status null when not in active or unattached state
by donagh.moran＠oracle.com 11 Oct '19

11 Oct '19

Hi as the subject suggests I'm having problems reading the state of the Storage Domain when not in one of two states active or unattached. I am developing in Java an reading the state with the piece of code below StorageDomain sd = sysService.storageDomainsService().list() .search(storageDomainName) .send() .storageDomains() .get(0); sd.status(); Issue when deactivating In the UI it goes from active too inactive. When I recursively get the storage domain and check its status via the SDK the status never gets set to inactive, instead it goes from inactive to null and stays o a null state. Issue when activating In the UI it goes from unattached, locked then active. When I recursively get the storage domain and check its status via the SDK it goes from unattached null then active. As far as I can tell the only two states detected are unattached and active out of the ENUM of possible states listed below, of which non are null. I presume as I can check for two of the eight possible states, that means I am correct in my approach. ACTIVATING("activating"), ACTIVE("active"), DETACHING("detaching"), INACTIVE("inactive"), LOCKED("locked"), MAINTENANCE("maintenance"), MIXED("mixed"), PREPARING_FOR_MAINTENANCE("preparing_for_maintenance"), UNATTACHED("unattached"), UNKNOWN("unknown"), Any help would be much appreciated, on whether this is a potential known or unknown bug or whether I doing something wrong in my approach to retrieving the state of the domain. Regards Donagh

2 2

Creating a custom NON-VM Network using the Ovirt SDK
by Jamie Holohan 10 Oct '19

10 Oct '19

If i'm creating a a custom network on OVM using the UI, one of the options in the pop up is a check box labelled "VM network" for determining if I want a VM network. When using the SDK I am building network with a NetworkBuilder, but I cannot see any methods to toggle the VM network option. How do I create a custom Network with not VM role using the SDK? Can it be done with a NetworkBuilder?

1 0

Ovirt System Test Results View on web not accessible
by raymond.francis＠oracle.com 10 Oct '19

10 Oct '19

https://ovirt-system-tests.readthedocs.io/en/latest/general/running_tests... This contains the following instructions... Once you've located the engine VM's IP, add it to /etc/hosts followed by the name engine. NOTE: any other name than engine will not work. Now, log in to the web-UI at: URL: https://engine/ovirt-engine/webadmin/ Username: admin Password: 123 Profile: internal These instructions, do you read them as A) The input to a curl command? curl --user admin:123 https://engine/ovirt-engine/webadmin/ -v --insecure or B) To use the url in a browser I was thinking B, but that would negate the need to update the hosts file i.e How would the browser know the value of engine? Either way i cant view them, any ideas?

1 0

Change Attach All/Require All checkbox values using SDK
by Jamie Holohan 10 Oct '19

10 Oct '19

Using the SDK is it possible to change the status of the Attach All checkbox for a given network. I have done this to update the status of the Require All checkbox (Java): sysService.clustersService().clusterService(ClusterObject.id()).networksService().networkService(NetworkObject).id()).update().network(network().required(false)).send(); Is it possible to do something similar for Attach All?

2 2

EL8 builds fail to mount loop device - kernel too old?
by Nir Soffer 10 Oct '19

10 Oct '19

I'm trying to run imageio tests on el8 mock, and the tests fail early when trying to create storage for testing: [userstorage] INFO Creating filesystem /var/tmp/imageio-storage/file-512-ext4-mount Suggestion: Use Linux kernel >= 3.18 for improved stability of the metadata and journal checksum features. [userstorage] INFO Creating file /var/tmp/imageio-storage/file-512-ext4-mount/file [userstorage] INFO Creating backing file /var/tmp/imageio-storage/file-512-xfs-backing [userstorage] INFO Creating loop device /var/tmp/imageio-storage/file-512-xfs-loop [userstorage] INFO Creating filesystem /var/tmp/imageio-storage/file-512-xfs-mount mount: /var/tmp/imageio-storage/file-512-xfs-mount: wrong fs type, bad option, bad superblock on /dev/loop4, missing codepage or helper program, or other error. Traceback (most recent call last): File "/usr/local/bin/userstorage", line 10, in <module> sys.exit(main()) File "/usr/local/lib/python3.6/site-packages/userstorage/__main__.py", line 42, in main create(cfg) File "/usr/local/lib/python3.6/site-packages/userstorage/__main__.py", line 52, in create b.create() File "/usr/local/lib/python3.6/site-packages/userstorage/file.py", line 47, in create self._mount.create() File "/usr/local/lib/python3.6/site-packages/userstorage/mount.py", line 53, in create self._mount_loop() File "/usr/local/lib/python3.6/site-packages/userstorage/mount.py", line 94, in _mount_loop ["sudo", "mount", "-t", self.fstype, self._loop.path, self.path]) File "/usr/lib64/python3.6/subprocess.py", line 311, in check_call raise CalledProcessError(retcode, cmd) subprocess.CalledProcessError: Command '['sudo', 'mount', '-t', 'xfs', '/var/tmp/imageio-storage/file-512-xfs-loop', '/var/tmp/imageio-storage/file-512-xfs-mount']' returned non-zero exit status 32. https://jenkins.ovirt.org/job/ovirt-imageio_standard-check-patch/1593//arti… Same code runs fine in Travis: https://travis-ci.org/nirs/ovirt-imageio/jobs/595794863 And also locally on Fedora 29: $ ../jenkins/mock_configs/mock_runner.sh -C ../jenkins/mock_configs -p el8 ... ## Wed Oct 9 23:37:22 IDT 2019 Finished env: el8:epel-8-x86_64 ## took 85 seconds ## rc = 0 My guess is that we run el8 jobs on el7 hosts with old kernels (Suggestion: Use Linux kernel >= 3.18 for improved stability of the metadata and journal checksum features.) This issue will affects vdsm, using similar code to create storage for testing. For vdsm the issue is more tricky, since it requires same host/distro: 49 - tests-py37: 50 runtime-requirements: 51 host-distro: same So I think we need: - make slaves with newer kernel (fc29? fc30?) with the el8 mock env - add el8 slaves for running el8 mock with "host-distro: same" If we don't have a solution we need to disable el8 tests, or continue testing without storage, which will skip about 200 tests. Nir

3 3